need to fix

GPM5

声音,关功放

 

rpm -qf /sbin/poweroff 

rpm -qi sysvinit-2.86-18

直接用ftp下载

 

rpm2cpio coreutils-5.2.1-31.8.el4_7.1.src.rpm| cpio -idv

bzip2 -d coreutils-5.2.1.tar.bz2

 

cat

++++++++++++++++++++++++++++++
kfifo机制
del on board sw low layer control, let the upper layer control it
sdhci-s3c里面share就可以,在s3c-keypad.c里面share就不可以。
开关--》ioctl-->打开电源--》(关键是如何走到probe)激活中断
status_wifi初始值,怎么告诉上层
PM_SUSPEND_ENBALE
可能是哪儿,把关了
++++++++++++++++++++++++++++++++
没有背光侧着也能看出来
不是GPIO模式的设置问题
tcon = __raw_readl(S3C_TCON);
tcfg1 = __raw_readl(S3C_TCFG1);
tcfg0 = __raw_readl(S3C_TCFG0);
__raw_read(tcnt, S3C_TCNTB(channel));
__raw_read(tcmp, S3C_TCMPB(channel));
enter s3cfb_set_brightness, val = 50 
tcon = 0x50000a, tcfg0 = 0x6ff, tcfg1 = 0x10, tcnt = 0x1c2, tcmp = 0xfa 
enter s3cfb_set_brightness, val = 30 
tcon = 0x50000a, tcfg0 = 0x6ff, tcfg1 = 0x10, tcnt = 0x1c2, tcmp = 0x96 
enter s3cfb_set_brightness, val = 50 
tcon = 0x50000a, tcfg0 = 0x6ff, tcfg1 = 0x10, tcnt = 0x1c2, tcmp = 0xfa 
enter s3cfb_set_brightness, val = 10 
tcon = 0x50000a, tcfg0 = 0x6ff, tcfg1 = 0x10, tcnt = 0x1c2, tcmp = 0x32 
加上打印后,调剂背光没有反应
???为什么???
SVN有的是一行多个缩进导致不一样
modprobe libertas_sdio helper_name=/lib/firmware/sd8686_helper.bin fw_name=/lib/firmware/sd8686.bin
+++++++++++++++++++++++++++++++++++++++
wifi需要重启么
1.放在init fbmid之后
LCD电源很早开,但是背光之内的都后开
在之后开,也不是很稳定。
可能还是要很早开LCD电源,之后开背光
S3C_LCD clock got enabled :: 133.000 Mhz
LCD TYPE :: L70T84 will be initialized
Window[0] - FB1: map_video_memory: clear ff000000:0012c000
            FB1: map_video_memory: dma=5f200000 cpu=ff000000 size=0012c000
Window[0] - FB2: map_video_memory: clear ff096000:00096000
            FB2: map_video_memory: dma=5f296000 cpu=ff096000 size=00096000
Console: switching to colour frame buffer device 80x30
fb0: s3cfb frame buffer device
Window[1] - FB1: map_video_memory: clear ff12c000:0012c000
            FB1: map_video_memory: dma=5f400000 cpu=ff12c000 size=0012c000
Window[1] - FB2: map_video_memory: clear ff1c2000:00096000
            FB2: map_video_memory: dma=5f496000 cpu=ff1c2000 size=00096000
fb1: s3cfb frame buffer device
Window[2] - FB1: map_video_memory: clear ff258000:00096000
            FB1: map_video_memory: dma=5f600000 cpu=ff258000 size=00096000
fb2: s3cfb frame buffer device
Window[3] - FB1: map_video_memory: clear ff2ee000:00096000
            FB1: map_video_memory: dma=5f700000 cpu=ff2ee000 size=00096000
fb3: s3cfb frame buffer device
enter backlight_power_ctrl, value = 1 
enter lcd_power_ctrl, value = 1 
lcd_power_ctrl: LCD Vcc opened 
lcd_power_ctrl: LCD GPE1 opened 
wifi initial state is off and we switch off wifi 
GPIO-154 autorequested
GPIO for wifi reset excute over~~~ 
GPIO-200 autorequested
GPIO-34 autorequested
3g initial state is on and we switch on 3g
[bdctl_init]: bdctl init success
bdctl实际上还在那之后
所以要把LCD电源打开放到最开始去
50欧姆
gpio is what??
gpio_direction_output(S3C64XX_GPF(14), 1);
gpio_set_value(S3C64XX_GPE(0), 1);
mdelay(20);
gpio_direction_output(S3C64XX_GPE(1), 1);
gpio_direction_output和gpio_set_value之间的区别
1/2
3/2=1
100
129
会花掉,最好改变下
++++++++++++++++++++++++++++++++++++++++
SP6654U
处的POWER进口处,L16去掉后对VDD_IO有较大改善。
去掉后,纹波明显变小,即使LCD的V3.3v不变也很好。
LDO工作状态不对导致锁定。
更换L17无效果
更换L11
R172
4号板子换成10nf
内核更改上电顺序
都不行
悬空装填
lcd modify need verify
//optimise lcd power up sequece
R162要焊掉
L16更换后文件系统不再报错
峰值840ma 3g
800 wifi
+++++++++++++++++++++++++++++++++++++++++++++

  • 0
    点赞
  • 0
    收藏
    觉得还不错? 一键收藏
  • 0
    评论
评论
添加红包

请填写红包祝福语或标题

红包个数最小为10个

红包金额最低5元

当前余额3.43前往充值 >
需支付:10.00
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明:

1.余额是钱包充值的虚拟货币,按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载,可以购买VIP、付费专栏及课程。

余额充值