MTK平台前后摄使用PMIC供电无法设置不同的DVDD电压

xx项目前后摄DVDD共用PMIC供电，一供后摄DVDD电压设置为1.2V，二供后摄DVDD电压设置为1.1V，一二供前摄DVDD电压设置为1.2V，但实际测试过程中发现二供机器前摄的DVDD电压只有1.1V。

分析过程如下：

1.查看开机camera相关上电log，设置电压时无明显报错，怀疑模组硬件本身影响

2.拆掉前摄模组，DVDD依然是1.1V，达不到1.2V

3.因为此项目前后摄共用PMU的VCAMD给DVDD供电，怀疑后摄影响前摄的供电，将后摄模组拆掉，前摄的DVDD上电依然是1.1V

4.将二供后摄DVDD电压改为1.2V上电，此时前摄DVDD电压可以达到1.2V

5.给MTK提case，MTK提供用adb命令控制PMU输出的方法，发现写adb命令可以让DVDD达到1.2V，说明还是软件问题

6.修改软件，将二供后摄放在一供后摄之前上电，此方案可以在一供机器上实现前摄DVDD达到1.2V，但在二供机器上前摄DVDD还是1.1V

7.在上电过程中打开log开关以及增加log，发现二供机器在设置DVDD电压时设置失败了，log如下：

[    8.890901] (0)[659:camerahalserver][imgsensor][imgsensor_hw_power] sensor_idx 1, power 1 curr_sensor_name fh10_hi846_front_st_mipi_raw, enable list fh10_hi846_front_st_mipi_raw fh10_gc5035_front_lhyx_mipi_raw fh10_hi556_front_st_mipi_raw

[    8.890917] (0)[659:camerahalserver]vcamd: Restricting voltage, 1200000-1100000uV

[    8.890926] (0)[659:camerahalserver][imgsensor][regulator_set] [regulator]fail to regulator_set_voltage, powertype:4 powerId:1200000

追踪代码发现问题出在kernel-4.19/drivers/regulator/core.c中的regulator_check_consumer函数中，进一步在此函数中添加log，log打印如下：

<6>[    8.511500]  (1)[682:camerahalserver][imgsensor][imgsensor_hw_power] sensor_idx 1, power 1 curr_sensor_name fh10_hi846_front_st_mipi_raw, enable list fh10_hi846_front_st_mipi_raw fh10_gc5035_front_lhyx_mipi_raw fh10_hi556_front_st_mipi_raw

<4>[    8.511509]  (1)[682:camerahalserver]3056, zm: voltage->min_uV = 0, min_uv = 1200000, voltage->max_uV = 0, max_uV = 1200000

<4>[    8.511513]  (1)[682:camerahalserver]3081, zm: call regulator_check_voltage

<4>[    8.511518]  (1)[682:camerahalserver]3086, zm: compare min_uV:1200000, max_uV:1200000

<4>[    8.511523]  (1)[682:camerahalserver]3092, zm: compare voltage->min_uV:1200000, voltage->max_uV:1200000

<4>[    8.511528]  (1)[682:camerahalserver]3093, zm: call regulator_check_consumers

<4>[    8.511533]  (1)[682:camerahalserver]332, zm: min_uV:1200000, max_uV:1200000

<4>[    8.511560]  (1)[682:camerahalserver]342, zm: voltage->min_uV:1200000, voltage->max_uV:1200000

<4>[    8.511590]  (1)[682:camerahalserver]342, zm: voltage->min_uV:1100000, voltage->max_uV:1100000

<4>[    8.511597]  (1)[682:camerahalserver]349, zm: max_uV:1100000

<4>[    8.511602]  (1)[682:camerahalserver]357, zm: compare min_uV:1200000, max_uV:1100000

<3>[    8.511614]  (1)[682:camerahalserver]vcamd: Restricting voltage, 1200000-1100000uV

<3>[    8.511627]  (1)[682:camerahalserver][imgsensor][regulator_set] 273, [regulator]fail to regulator_set_voltage, powertype:4 powerId:1200000

添加log后的regulator_check_consumers函数如下：

static int regulator_check_consumers(struct regulator_dev *rdev,

                      int *min_uV, int *max_uV,

                      suspend_state_t state)