浪潮服务器在SUSE下的硬盘和网卡驱动及双网卡绑定

5555,刚写的东西又没了。

1、浪潮服务器下的SCSI硬盘驱动：
    得到驱动程序后，1. 引导后选择manual installation，按F6键，插入驱动软盘
				    2.进入main menu菜单，选择kernel modules(haraware driver)
				    3.选择add driver update
				    4.选择floppy加载驱动
				(注意：如果用户使用usb软驱，需要加载usb floppy 模块)

2、网卡驱动
    服务器：NF280D
    先安装源码和部分开发包。
    接下来就是对驱动程序做make 和make  install，再modprobe e1000，打开yast进往以网络设备就可以看到已经识别到网卡。

3、双网卡绑定

#!/bin/bash

#双网卡绑定使用方法

#将bond脚本复制到/etc/init.d/下，确保权限为755
#确保在Yast里最好不要对需要绑定的网卡作设置,如果有，将设备删除，使之处于未设置的状态。
#根据自身需要修改以下变量，然后用chkconfig命令将bond服务在3,5运行级别启用。
#然后到/etc/init.d/rc3.d,和/etc/init.d/rc5.d/下检查bond服务是否运行在network
#之后,如果不是，则需要手工链接。
#bond_ip    需要设置的IP
#bond_netmask    子网掩码
#bond_gw    缺省网关
#bond_mode    绑定的模式
#host_route_ip    主机路由的IP,如果没有，留空
#host_route_dev    主机路由的设备

#dev_list    需要绑定的设备名称，用空格分开
#primary_eth    主设备名称

bond_ip=192.168.1.18
bond_netmask=255.255.255.0
bond_gw=192.168.1.1
bond_mode=active-backup
#bond_mode=balance_rr
host_route_ip=192.168.2.1
host_route_dev=bond0

dev_list="eth0 eth1"
primary_eth="eth0"
mii_val=100
dev_num=`echo $dev_list | awk '{print NF}'`

function wait_real_interfaces() {
    local max_wait=120
    local wait_count=0
    local chk_dev_count=0
    local dev=""

    while [ 0 ];do
        chk_dev_count=0
        #Check each device in the list
        for dev in $dev_list;do
            chk_eth=`cat /proc/net/dev | awk '{print $1}' | grep "$dev:" | sed 's/:[0-9]*//' | wc -l`
            if [ $chk_eth -eq 1 ];then
                chk_dev_count=$[chk_dev_count+1]
            fi
        done

        if [ $wait_count -eq $max_wait ];then
            echo "Max waits reached,abort to wait real interfaces!"
            exit 1
        fi

        if [ $chk_dev_count -eq $dev_num ];then
            return 0
        fi

        wait_count=$[wait_count+1]
        echo "Bonding network : waiting for real interfaces,retry at $wait_count,max waits is $max_wait"
        sleep 1
    done
}

function check_real_interfaces() {
    local chk_eth=0
    local chk_dev_count=0

    for dev in $dev_list;do
        chk_eth=`ifconfig -a $dev | grep $dev | awk '{print $1}' | wc -l`
        if [ $chk_eth -eq 1 ];then
            chk_dev_count=$[chk_dev_count+1]
        fi
    done

    if [ $chk_dev_count -eq $dev_num ];then
        return 0
    fi

    return 1
}

function check_bond_device() {
    local chk_num=$[dev_num+1]

    chk_bond=`ifconfig | grep "$bond_ip" | wc -l`
    if [ $chk_bond -eq $chk_num ];then
        echo "--------------------------------------------------------------------------------"
        echo "Bond IP : $bond_ip , Netmask : $bond_netmask , Gateway : $bond_gw"
        echo "Bonding network devices are successfully setup!"
        echo "--------------------------------------------------------------------------------"
        return 0
    else
        echo "Bonding network device is NOT setup correctly!"
        return 1
    fi
}

function init_bond_device() {
    local dev=""
    modprobe bonding mode=$bond_mode miimon=$mii_val primary=$primary_eth
    ifconfig bond0 inet $bond_ip netmask $bond_netmask
    if [ -n "$host_route_ip" -a -n "$host_route_dev" ];then
        route add -host $host_route_ip dev $host_route_dev
    fi
    route add default gw $bond_gw

    stop_real_devices

    for dev in $dev_list;do
        ifconfig $dev up
        ifenslave bond0 $dev
    done

    ifconfig bond0 up
}

function start_bond_device() {
    local max_attempt=30
    local attempt_count=0
    local interval=3
    
    while [ 0 ];do
        wait_real_interfaces
        if [ $? -eq 0 ];then
            echo "All real network devices are initialized!"
        fi

        check_real_interfaces
        if [ $? -eq 1 ];then
            continue
        fi

        echo "Wait for $interval seconds to bind real interface..."
        sleep $interval
        init_bond_device

        check_bond_device
        if [ $? -eq 0 ];then
            break
        else
            stop_bond_device
            attempt_count=$[attempt_count+1]
            echo "Binding real interfaces,retry at $attempt_count,max attempts is $max_attempt"
            if [ $attempt_count -eq $max_attempt ];then
                echo "Max attempt retry reached,abort to setup bonding network!"
                exit 1
            fi
            continue
        fi
    done
}

function stop_real_devices() {
    local dev=""

    #stop all devices in the list
    for dev in $dev_list;do
       ifdown $dev 2>&1 > /dev/null
    done

    #stop every real devices that may be configured as the same ip address
    for dev in `cat /proc/net/dev | grep eth | sed 's/:.*//'`;do
        chk_ip=`ifconfig $dev | grep $bond_ip | wc -l`
        if [ $chk_ip -eq 1 ];then
            ifdown $dev 2>&1 > /dev/null
        fi
        chk_ip=0
    done
}

function stop_bond_device() {
    local dev=""

    chk_bond=`ifconfig | grep bond`
    if [ -z "$chk_bond" ];then
        echo "Bonding device is not up,no need to stop"
        return 0
    fi

    echo "Stopping bonding devices..."
    for dev in $dev_list;do
        ifenslave -d bond0 $dev
    done

    stop_real_devices

    ifconfig bond0 down
    rmmod bonding
}


case $1 in
#Initialize bonding device,try every times until everything is OK
    start)
        start_bond_device
        ;;

#Unbind and stop the bonding & real network interfaces
    stop)
        stop_bond_device
        ;;

#Reset the bonding devices
    restart)
        stop_bond_device
        start_bond_device
        ;;
#Show status for bonding device
    status)
        check_bond_device
        ;;
    *)
        echo "Usage:`basename $0` [ start | stop | restart | status]"
        exit 0
        ;;
esac

exit 0