RIP实验练习

无妄之灾|

已于 2023-05-02 21:02:27 修改

阅读量55

点赞数

分类专栏： RIP 文章标签：智能路由器网络

于 2023-05-02 20:50:15 首次发布

本文链接：https://blog.csdn.net/2201_75408313/article/details/130465675

版权

RIP 专栏收录该内容

1 篇文章 0 订阅

订阅专栏

该配置过程描述了如何在三个路由器R1、R2和R3上设置RIP版本1，以连接不同的网络段，并通过配置DHCP服务在接口GigabitEthernet0/0/0上提供IP地址分配。所有路由器的链路状态已进入UP，确保了网络通信。

摘要由CSDN通过智能技术生成

1.拓扑图

2.需求分析

路由器上分别配置环回
连接路由器的线路网段为12.1.1.0/24、23.1.1.0/24
R1和R3连接的网络地址分别为192.168.1.0/24、192.168.2.0/24
整个网络使用RIP达到全网可达

3.所有配置内容

[r1]interface GigabitEthernet 0/0/0
[r1-GigabitEthernet0/0/0]ip address 192.168.1.1 24
May  2 2023 20:26:12-08:00 r1 %%01IFNET/4/LINK_STATE(l)[0]:The line protocol IP 
on the interface GigabitEthernet0/0/0 has entered the UP state. 
[r1-GigabitEthernet0/0/0]q

[r1]interface GigabitEthernet 0/0/1
[r1-GigabitEthernet0/0/1]ip address 12.1.1.1 24
May  2 2023 20:26:59-08:00 r1 %%01IFNET/4/LINK_STATE(l)[2]:The line protocol IP 
on the interface GigabitEthernet0/0/1 has entered the UP state. 
[r1-GigabitEthernet0/0/1]q

[r1]interface loopback 1
[r1-LoopBack1]ip address 1.1.1.1 32
[r1-LoopBack1]q

[r1]rip 1
[r1-rip-1]version 1
[r1-rip-1]network 1.0.0.0
[r1-rip-1]network 12.0.0.0
[r1-rip-1]network 192.168.1.0
[r1-rip-1]q

[r1]dhcp enable
Info: The operation may take a few seconds. Please wait for a moment.done.
[r1]ip pool 1
Info: It's successful to create an IP address pool.
[r1-ip-pool-1]network 192.168.1.0 mask 24
[r1-ip-pool-1]gateway-list 192.168.1.1
[r1-ip-pool-1]dns-list 8.8.8.8
[r1-ip-pool-1]q
[r1]interface GigabitEthernet 0/0/0
[r1-GigabitEthernet0/0/0]dhcp select global
[r1-GigabitEthernet0/0/0]q

[r2]interface GigabitEthernet 0/0/0
[r2-GigabitEthernet0/0/0]
[r2-GigabitEthernet0/0/0]ip address 12.1.1.2 24
May  2 2023 20:35:54-08:00 r2 %%01IFNET/4/LINK_STATE(l)[0]:The line protocol IP 
on the interface GigabitEthernet0/0/0 has entered the UP state. 
[r2-GigabitEthernet0/0/0]q

[r2]interface GigabitEthernet 0/0/1
[r2-GigabitEthernet0/0/1]ip address 23.1.1.1 24
May  2 2023 20:36:16-08:00 r2 %%01IFNET/4/LINK_STATE(l)[1]:The line protocol IP 
on the interface GigabitEthernet0/0/1 has entered the UP state. 
[r2-GigabitEthernet0/0/1]q

[r2]interface loopback 1
[r2-LoopBack1]ip address 2.2.2.2 32
[r2-LoopBack1]q

[r2]rip 1
[r2-rip-1]version 1
[r2-rip-1]network 2.0.0.0
[r2-rip-1]network 12.0.0.0
[r2-rip-1]network 23.0.0.0
[r2-rip-1]q

[r3]interface GigabitEthernet 0/0/0
[r3-GigabitEthernet0/0/0]
[r3-GigabitEthernet0/0/0]ip address 23.1.1.2 24
May  2 2023 20:40:03-08:00 r3 %%01IFNET/4/LINK_STATE(l)[0]:The line protocol IP 
on the interface GigabitEthernet0/0/0 has entered the UP state. 
[r3-GigabitEthernet0/0/0]q

[r3]interface GigabitEthernet 0/0/1
[r3-GigabitEthernet0/0/1]ip address 192.168.2.1 24
May  2 2023 20:40:28-08:00 r3 %%01IFNET/4/LINK_STATE(l)[1]:The line protocol IP 
on the interface GigabitEthernet0/0/1 has entered the UP state. 
[r3-GigabitEthernet0/0/1]q

[r3]interface loopback 1
[r3-LoopBack1]ip address 3.3.3.3 32
[r3-LoopBack1]q

[r3]rip 1
[r3-rip-1]version 1
[r3-rip-1]network 3.0.0.0
[r3-rip-1]network 23.0.0.0
[r3-rip-1]network 192.168.2.0
[r3-rip-1]q

[r3]dhcp enable
Info: The operation may take a few seconds. Please wait for a moment.done.
[r3]ip pool 1
Info: It's successful to create an IP address pool.
[r3-ip-pool-1]network 192.168.2.0 mask 24
[r3-ip-pool-1]gateway-list 192.168.2.1
[r3-ip-pool-1]dns-list 8.8.8.8
[r3-ip-pool-1]q
[r3]interface GigabitEthernet 0/0/1
[r3-GigabitEthernet0/0/1]
[r3-GigabitEthernet0/0/1]dhcp select global
[r3-GigabitEthernet0/0/1]q

4.测试结果