HICP实验

要求：R1-R2-R3-R4-R5 RIP 100 运行版本2     R6-R7 RIP 200 运行版本1

1.使用合理IP地址规划网络，各自创建环回接口
2.R1创建环回 172.16.1.1/24 172.16.2.1/24 172.16.3.1/24
3.要求R3使用R2访问R1环回
4.减少路由条目数量，R1-R2之间增加路由传递安全性
5.R5创建一个环回模拟运营商，不能通告
6.R1 telnet R2环回实际telnet 到R7上
7.R6-R7路由器不能学习到达R1环回路由
8.全网可达

1.使用合理IP地址规划网络，各自创建环回接口

[r1]interface g0/0/0
[r1-GigabitEthernet0/0/0]ip add 14.1.1.1 24
[r1]interface g0/0/1
[r1-GigabitEthernet0/0/1]ip add 12.1.1.1 24
[r1]interface LoopBack 0
[r1-LoopBack0]ip add 1.1.1.1 24

[r1]rip 100  
[r1-rip-100]version 2  
[r1-rip-100]network 14.0.0.0
[r1-rip-100]network 12.0.0.0
[r1-rip-100]network 1.0.0.0

[r2]interface g0/0/0
[r2-GigabitEthernet0/0/0]ip add 12.1.1.2 24

[r2]interface g0/0/1
[r2-GigabitEthernet0/0/1]ip add 23.1.1.1 24
[r2]interface LoopBack 0
[r2-LoopBack0]ip add 2.2.2.2 24

[r2]rip 100
[r2-rip-100]version 2
[r2-rip-100]network 12.0.0.0
[r2-rip-100]network 23.0.0.0
[r2-rip-100]network 2.0.0.0

[r3]interface g0/0/0
[r3-GigabitEthernet0/0/0]ip add 34.1.1.1 24

[r3]interface g0/0/1
[r3-GigabitEthernet0/0/1]ip add 23.1.1.2 24
[r3]interface LoopBack 0
[r3-LoopBack0]ip add 3.3.3.3 24

[r3]rip 100
[r3-rip-100]version 2
[r3-rip-100]network 34.0.0.0
[r3-rip-100]network 23.0.0.0
[r3-rip-100]network 3.0.0.0

[r4]interface g0/0/0
[r4-GigabitEthernet0/0/0]ip add 14.1.1.2 24
[r4]interface g0/0/1
[r4-GigabitEthernet0/0/1]ip add 34.1.1.2 24
[r4]interface g0/0/2
[r4-GigabitEthernet0/0/2]ip add 45.1.1.1 24
[r4]interface g4/0/0
[r4-GigabitEthernet4/0/0]ip add 46.1.1.1 24

[r4]interface LoopBack 0
[r4-LoopBack0]ip add 4.4.4.4 24

[r4]rip 100
[r4-rip-100]version 2
[r4-rip-100]network 34.0.0.0
[r4-rip-100]network 14.0.0.0
[r4-rip-100]network 45.0.0.0
[r4-rip-100]network 46.0.0.0
[r4-rip-100]network 4.0.0.0

[r5]interface g0/0/0
[r5-GigabitEthernet0/0/0]ip add 45.1.1.2 24
[r5]interface LoopBack 0
[r5-LoopBack0]ip add 5.5.5.5 24

[r5]rip 100
[r5-rip-100]version 2
[r5-rip-100]network 45.0.0.0
[r5-rip-100]network 5.0.0.0

[r6]interface g0/0/0
[r6-GigabitEthernet0/0/0]ip add 46.1.1.2 24
[r6]interface g0/0/1
[r6-GigabitEthernet0/0/1]ip add 67.1.1.1 24
[r6]interface LoopBack 0
[r6-LoopBack0]ip add 6.6.6.6 24

[r6]rip 200
[r6-rip-200]version 1
[r6-rip-200]network 46.0.0.0
[r6-rip-200]network 67.0.0.0
[r6-rip-200]network 6.0.0.0

 [r7]interface g0/0/0
[r7-GigabitEthernet0/0/0]ip add 67.1.1.2 24
[r7]interface LoopBack 0
[r7-LoopBack0]ip add 7.7.7.7 24

[r7]rip 200
[r7-rip-200]version 1
[r7-rip-200]network 67.0.0.0
[r7-rip-200]network 7.0.0.0

 2.R1创建环回 172.16.1.1/24 172.16.2.1/24 172.16.3.1/24

[r1]interface LoopBack 1
[r1-LoopBack1]ip add 172.168.1.1 24
[r1]interface LoopBack 2
[r1-LoopBack2]ip add 172.168.2.1 24
[r1]interface LoopBack 3
[r1-LoopBack3]ip add 172.168.3.1 24
[r1]rip 100
[r1-rip-100]version 2
[r1-rip-100]network 172.16.0.0

 3.要求R3使用R2访问R1环回

[r3]acl 2000
[r3-acl-basic-2000]rule permit source 1.1.1.0 0
[r3-acl-basic-2000]rule permit source 172.16.0.0 0
[r3]interface g0/0/0
[r3-GigabitEthernet0/0/0]rip metricin 2000 2

 4.减少路由条目数量，R1-R2之间增加路由传递安全性

[r1]interface g0/0/0
[r1-GigabitEthernet0/0/0]rip summary-address 172.16.0.0 255.255.252.0
[r1]interface g0/0/1
[r1-GigabitEthernet0/0/1]rip summary-address 172.16.0.0 255.255.252.0

[r1]interface g0/0/0 
[r1-GigabitEthernet0/0/0]rip authentication-mode md5 nonstandard cipher cisco 12
[r2]interface g0/0/0
[r2-GigabitEthernet0/0/0]rip authentication-mode md5 nonstandard cipher cisco 12

 5.R5创建一个环回模拟运营商，不能通告

[r5]interface LoopBack 1
[r5-LoopBack1]ip add 55.5.5.5 32  
[r5-LoopBack1]rip 100
[r5-rip-100]default-route originate 

 6.R1 telnet R2环回实际telnet 到R7上

[r6]interface g0/0/0
[r6-GigabitEthernet0/0/0]rip version 2

[r7]aaa
[r7-aaa]local-user wyy privilege level 15 password  cipher 123
[r7-aaa]local-user wyy service-type telnet
[r7]user-interface vty 0 4
[r7-ui-vty0-4]authentication-mode aaa

 7.R6-R7路由器不能学习到达R1环回路由

[r6]acl 2000
[r6-acl-basic-2000]rule deny source 1.1.1.0 0
[r6-acl-basic-2000]rule deny source 172.16.0.0 0
[r6-acl-basic-2000]rule permit source any
[r6]rip 200
[r6-rip-200]filter-policy 2000 import g0/0/0