找了几个ansys命令流，分享一下

/clear
/prep7                      !进入前处理
/PLOPTS,DATE,0            !设置不显示日期和时间
!=====设置单元和材料 
ET,1,BEAM3                !定义单元类型
R,1,2.19E-3,3.83e-6, , , , ,        !定义1号实常数用于顶梁侧梁
R,2,1.185E-3,1.87e-6,0,0,0,0,       !定义2号实常数用于弦杆
R,3,3.031E-3,8.47E-6,0,0,0,0,     !定义3号实常数用于底梁
MP,EX,1,2.1E11              !定义材料弹性模量
MP,PRXY,1,0.30              !定义材料泊松比
MP,DENS,1,,7800             !定义材料密度
!-----定义几何关键点 
K,1,0,0,, $ K,2,4,0,, $ K,3,8,0,, $ K,4,12,0,, $ K,5,16,0,, $ K,6,20,0,, $ K,7,24,0,, $ K,8,28,0,, $ K,9,32,0,, $ K,10,4,5.5,, $ K,11,8,5.5,, $ K,12,12,5.5,, $ K,13,16,5.5,, $ K,14,20,5.5,, $ K,15,24,5.5,, $ K,16,28,5.5,,
!-----通过几何点生成桥底梁的线
L,1,2 $ L,2,3 $ L,3,4 $ L,4,5 $ L,5,6 $ L,6,7 $ L,7,8 $ L,8,9 
!------生成桥顶梁和侧梁的线
L,9,16 $ L,15,16 $ L,14,15 $ L,13,14 $ L,12,13 $ L,11,12 $ L,10,11 $ L,1,10 
!------生成桥身弦杆的线 
L,2,10 $ L,3,10 $ L,3,11 $ L,4,11 $ L,4,12 $ L,4,13 $ L,5,13 $ L,6,13 $ L,6,14 $ L,6,15 $ L,7,15 $ L,7,16 $ L,8,16 
!------选择桥顶梁和侧梁指定单元属性 
LSEL,S,,,9,16,1,
LATT,1,1,1,,,, 
!-----选择桥身弦杆指定单元属性 
LSEL,S,,,17,29,1,
LATT,1,2,1,,,,
!-----选择桥底梁指定单元属性 
LSEL,S,,,1,8,1,
LATT,1,3,1,,,,
!------划分网格 
AllSEL,all                         !再恢复选择所有对象
LESIZE,all,,,1,,,,,1                  !对所有对象进行单元划分前的分段设置 
LMESH,all                        !对所有几何线进行单元划分  
!=====在求解模块中，施加位移约束、外力，进行求解
/solu
NSEL,S,LOC,X,0                    !根据几何位置选择节点 
D,all,,,,,,ALL,,,,,                     !对所选择的节点施加位移约束
AllSEL,all                          !再恢复选择所有对象 
NSEL,S,LOC,X,32                   !根据几何位置选择节点
D,all,,,,,,,UY,,,,                       !对所选择的节点施加位移约束
ALLSEL,all                         !再恢复选择所有对象  
!------基于几何关键点施加载荷
FK,4,FY,-5000  $ FK,6,FY,-5000  $ FK,5,FY,-10000
/replot                             !重画图形
Allsel,all                           !选择所有信息(包括所有节点、单元和载荷等)
solve                              !求解
!=====进入一般的后处理模块 
/post1                             !后处理
PLNSOL, U,Y, 0,1.0                  !显示Y方向位移
PLNSOL, U,X, 0,1.0                 !显示X方向位移
!------显示线单元轴力------
ETABLE,bar_I,SMISC, 1
ETABLE,bar_J,SMISC, 1
PLLS,BAR_I,BAR_J,0.5,1             !画出轴力图 
finish                              !结束
et,1,13,4
et,2,13,4
!==============
mptemp,1,20,500,800,1200,1500
mpdata,ex,1,1,2.09e11,1.72e11,1.33e11,0.84e11,0.45e11
mpplot,ex,1
finish
/clear,start
/title,fff
/prep7
/unit,si
et,1,13,4
et,2,13,4
!==============
mptemp,1,20,500,800,1200,1500
mpdata,ex,1,1,2.09e11,1.72e11,1.33e11,0.84e11,0.45e11
mpplot,ex,1

finish
/clear,start
/title,fff
/prep7
/unit,si
et,1,13,4
et,2,13,4
!=============
mptemp,1,20,500,800,1200,1500
mpdata,ex,1,1,2.09e11,1.72e11,1.33e11,0.84e11,0.45e11
mpdata,ex,2,1,2.16e11,1.78e11,1.42e11,1.04e11,0.68e11
!================
tb,kinh,1,1,5,0    !一个温度点，5个数据点
tbtemp,0
tbpt,,0.0015534,320
tbpt,,0.00288,325
tbpt,,0.00864,370
tbpt,,0.01536,420
tbpt,,0.03866,530
tbplot
!=========================
tb,bkin,2,5    !通过5个温度点，不通过数据点定义
tbtemp,20,1
tbdata,1,315e6,2.09e10
tbtemp,500,2
tbdata,1,212e6,1.72e10
tbtemp,800,3
tbdata,1,153e6,1.33e10
tbtemp,1200,4
tbdata,1,93e6,0.84e10
tbtemp,1500,5
tbdata,1,33e6,0.45e10
TBPLOT

钢球淬火
/clear
/filname,ball_thermal
/prep7
et,1,plane55
keyopt,1,1,0    !设置关键点选项
keyopt,1,3,1
keyopt,1,4,0
keyopt,1,8,0
keyopt,1,9,0
!=====设置材料参数==========
mptemp,1,0        
mpdata,ex,1,,2.2e11
mpdata,prxy,1,,0.28
mpdata,dens,1,,7800
mpdata,alpx,1,,1.3e-6
mpdata,kxx,1,,70
mpdata,c,1,,488
uimp,1,reft,,,0
!========建立模型==============
pcirc,0.1,,,90
lesize,all,,,20
amesh,all
!=========求解================
/solu
antype,4        !选择瞬态分析
time,60
autots,off
deltim,0.4,
outres,all,all
tunif,500        !对所有节点施加一个均布温度
lsel,s,,,1
nsll,s,1
sf,all,conv,650,0    !对曲线上的节点施加对流条件
allsel,all
save
solve
finish
/post26
numvar,200
nsol,2,22,temp    !将中心点的温度定义为一个变量，变量名为2
plvar,2
finish
/post1
plnsol,temp
antime,10,0.5,,1,0,0,0    !生成动画
finish

杯子建模
/clear,start
/prep7
k,1,0,0,0        !创建关键点
k,2,0.0395,0,0
k,3,0.05,0.12,0
k,4,0.047,0.12,0
k,5,0.0367,0.003,0
k,6,0,0.003,0
lstr,1,2        !将关键点连成一条直线
lstr,2,3
lstr,3,4
lstr,4,5
lstr,5,6
lstr,6,1
lfillt,1,2,0.02    !线倒角
lfillt,4,5,0.017
al,all        !将所有线连接构成一个平面
vrotat,all,,,,,,1,6,360    !将面绕1,6关键点连成的轴线旋转360°生成体
k,31,0,0.103,0
k,32,0.078,0.103,0
k,33,0.078,0.046,0
k,34,0,0.0011,0
lstr,31,32
lstr,32,33
lstr,33,34
lfillt,54,55,0.013
lfillt,55,56,0.028
k,41,0,0.105,0.005
k,42,0,0.105,-0.005
k,43,0,0.101,-0.005
k,44,0,0.101,0.005
lstr,41,42
lstr,42,43
lstr,43,44
lstr,44,41
lfillt,59,60,0.001
lfillt,60,61,0.001
lfillt,61,62,0.001
lfillt,62,59,0.001
al,59,63,60,64,61,65,62,66    !将选择的线连接成为一个平面
vdrag,33,,,,,,54,57,55,58,56    !将面33沿着线54,57,55,58,56扫掠生成体
vsel,s,,,5,9,4    !选择编号为5和9的体
asel,s,,,4,28,24    !选择编号为4和28的面
vsba,all,all    !用选择的面来分割选择的体
allsel,all
vdele,10,,,1    !删除体
vdele,13,,,1
/pnum,volu,1    !打开实体编号显示
/number,1    !只显示颜色，不显示编号
/color,volu,yell,all    !将所有实体颜色改为黄色
/replot
finish

刹车盘
/clear
/prep7
!===草图1====
k,1,0,0,0               !生成关键点
k,2,0,8,0
k,3,70,8,0
k,4,70,28,0
k,5,150,28,0
k,6,150,20,0
k,7,80,20,0
k,8,80,0,0
!===========
a,1,2,3,4,5,6,7,8       !生成一个面
vrotat,1,,,,,,1,2,,2    !将面旋转生成体
wprota,,-90             !将工作平面绕x轴逆时针旋转90°
cyl4,,,,,32,360,8       !建立一个半径32厚度为8的圆柱
vadd,1,2                !将1、2实体合并
vsbv,4,3                !用4号实体减去3号实体
!===
wpoffs,,,43             !移动工作平面
cyl4,,,93,0,150,360,8
!===========
wpoffs,,,-15
cyl4,103,0,,90,4,270,15
cyl4,141,0,,-90,4,90,15
blc4,103,-4,38,8,15
vadd,3,4,5
/pnum,volu,1            !打开实体编号显示
/replot
local,11,1,,,,,-90      !建立一个编号11的局部坐标系——柱坐标系
csys,11                 !激活该坐标系
vgen,36,6,,,,10         !将6号实体圆形阵列成36份
!============
csys,0            
wpoffs,,,23
cyl4,,,103,,140,45,7.5
vgen,2,39,,,,-38.5      !将刹车片阵列成2个