蓝牙驱动

/***************************************************************************************************************************

**原创：http://blog.csdn.net/kylin_fire_zeng  ， 欢迎转载分享，共同进步，但请注明出处啊，尊重他人成果。

***************************************************************************************************************************/

蓝牙驱动：

dts配置：

-----------------------

arch/arm/boot/dts/rk3128-box-rk88.dts"

-->

wireless-bluetooth {

                compatible = "bluetooth-platdata";

 

                //wifi-bt-power-toggle;

 

                uart_rts_gpios = <&gpio0GPIO_C1 GPIO_ACTIVE_LOW>;

                pinctrl-names ="default","rts_gpio";

                pinctrl-0 =<&uart0_rts>;

                pinctrl-1 =<&uart0_rts_gpio>;

 

                //BT,power_gpio =<&gpio4 GPIO_D3 GPIO_ACTIVE_HIGH>;

                BT,reset_gpio = <&gpio3GPIO_C5 GPIO_ACTIVE_HIGH>;

                BT,wake_gpio = <&gpio3GPIO_C4 GPIO_ACTIVE_HIGH>;

                BT,wake_host_irq =<&gpio3 GPIO_C6 GPIO_ACTIVE_LOW>;

 

                status = "okay";

        };

 

 &uart0{

                status = "okay";

                dma-names = "!tx","!rx";

        pinctrl-0 = <&uart0_xfer&uart0_cts>;

};

----------------------------

kernel/arch/arm/boot/dts/rk312x.dtsi

正在的uart0 配置在：

 uart0: serial@20060000 {

                compatible ="rockchip,serial";

                reg = <0x20060000 0x100>;

                interrupts = <GIC_SPI 20IRQ_TYPE_LEVEL_HIGH>;

                clock-frequency =<24000000>;

                clocks =<&clk_uart0>, <&clk_gates8 0>;

                clock-names ="sclk_uart", "pclk_uart";

                reg-shift = <2>;

                reg-io-width = <4>;

                dmas = <&pdma 2>,<&pdma 3>;

                #dma-cells = <2>;

                pinctrl-names ="default";

                pinctrl-0 = <&uart0_xfer&uart0_cts &uart0_rts>;

                status = "disabled";

        };

-----------------------------

kernel/arch/arm/boot/dts/rk312x-pinctrl.dtsi

 gpio0_uart0 {

                        uart0_xfer: uart0-xfer{

                                rockchip,pins =<UART0_SIN>,

                                               <UART0_SOUT>;

                                rockchip,pull =<VALUE_PULL_UPDOWN_DISABLE>;

 

 

                        };

 

                        uart0_cts: uart0-cts {

                                rockchip,pins =<UART0_CTSN>;

                        /*      rockchip,pull =<VALUE_PULL_DEFAULT>; */

                                rockchip,pull =<VALUE_PULL_UPDOWN_DISABLE>;

 

 

                        };

 

                        uart0_rts: uart0-rts {

                                rockchip,pins =<UART0_RTSN>;

                        /*      rockchip,pull =<VALUE_PULL_DEFAULT>; */

                                 rockchip,pull= <VALUE_PULL_UPDOWN_DISABLE>;

 

                        };

 

                        uart0_rts_gpio:uart0-rts-gpio {

                                rockchip,pins =<FUNC_TO_GPIO(UART0_RTSN)>;

                       /*       rockchip,pull =<VALUE_PULL_DEFAULT>; */

                                rockchip,pull =<VALUE_PULL_UPDOWN_DISABLE>;

 

                        };

                };

 

------------------

arch/arm/boot/dts/include/dt-bindings/pinctrl/rockchip-rk312x.h

#define UART0_SOUT0x2d22

#define UART0_SIN0x2d32

#define UART0_CTSN0x2d52

 

那上面关系完了。我们就开始讲解驱动了吧。

驱动：net/rfkill/rfkill-bt.c

----->

static int __initrfkill_rk_init(void)

{

    LOG("Enter %s\n", __func__);

returnplatform_driver_register(&rfkill_rk_driver);

}

 

static structplatform_driver rfkill_rk_driver = {

.probe= rfkill_rk_probe,

.remove= rfkill_rk_remove,

.driver= {

.name= "rfkill_bt",

.owner= THIS_MODULE,

.pm= &rfkill_rk_pm_ops,

        .of_match_table = of_match_ptr(bt_platdata_of_match),

},

};

 

static structof_device_id bt_platdata_of_match[] = {

    { .compatible = "bluetooth-platdata"},

    { }

};

这里的这个跟

wireless-bluetooth {

                compatible = "bluetooth-platdata";

………

}

刚好匹配上了。Ok,那就行了。进入rfkill_rk_probe 吧.

 

static intrfkill_rk_probe(struct platform_device *pdev)

{

structrfkill_rk_data *rfkill;

structrfkill_rk_platform_data *pdata = pdev->dev.platform_data;

       pdata = devm_kzalloc(&pdev->dev,sizeof(struct rfkill_rk_platform_data), GFP_KERNEL);

        ret =bluetooth_platdata_parse_dt(&pdev->dev, pdata);----->@1

 

pdata->name= (char*)bt_name;

       pdata->type =RFKILL_TYPE_BLUETOOTH;

 

         rfkill =devm_kzalloc(&pdev->dev, sizeof(*rfkill), GFP_KERNEL);

        rfkill->pdata= pdata;

         rfkill->pdev = pdev;

 g_rfkill = rfkill;

 

bluetooth_dir= proc_mkdir("bluetooth", NULL);

    sleep_dir = proc_mkdir("sleep",bluetooth_dir);

  ent = proc_create("lpm", 0,sleep_dir, &bluesleep_lpm);

  ent = proc_create("btwrite", 0,sleep_dir, &bluesleep_btwrite);

 

---

 注册对应的管脚功能。

    ret = rfkill_rk_setup_gpio(pdev,&pdata->poweron_gpio, pdata->name, "poweron");

    ret = rfkill_rk_setup_gpio(pdev,&pdata->reset_gpio, pdata->name, "reset");

    ret = rfkill_rk_setup_gpio(pdev,&pdata->wake_gpio, pdata->name, "wake");

    ret = rfkill_rk_setup_gpio(pdev,&pdata->rts_gpio, rfkill->pdata->name, "rts");

 

    wake_lock_init(&(rfkill->bt_irq_wl), WAKE_LOCK_SUSPEND,"rfkill_rk_irq_wl");

 

    ret = rfkill_rk_setup_wake_irq(rfkill);

 

  这里进行了注册。

    ret= rfkill_register(rfkill->rfkill_dev);

 

   platform_set_drvdata(pdev,rfkill);

LOG("%sdevice registered.\n", pdata->name);

这里整个

 

}

@1 ：

static intbluetooth_platdata_parse_dt(struct device *dev,

                  structrfkill_rk_platform_data *data)

{

if (of_find_property(node, "wifi-bt-power-toggle", NULL)){}

 

 gpio = of_get_named_gpio_flags(node,"uart_rts_gpios", 0, &flags);

gpio= of_get_named_gpio_flags(node, "BT,power_gpio", 0, &flags);

 gpio = of_get_named_gpio_flags(node,"BT,reset_gpio", 0, &flags);

gpio= of_get_named_gpio_flags(node, "BT,wake_gpio", 0, &flags);

gpio= of_get_named_gpio_flags(node, "BT,wake_host_irq", 0, &flags);

 

自己跟下面的dts配置比较一下吧。

 

----------> 这里可以单独其实就是读取dts文件，然后赋值给 *data 函数。

｝