redis5集群

前提：

redis环境默认搭建完毕，目录结构如下：

utils,redis-cluster不用在意，后面说。

1,创建目录（redis-cluster） 然后再下面创建6个文件夹，

mkdir 7001 7002 7003 7004 7005 7006

2,创建redis.conf文件

拷贝etc下面的redis.conf,稍作修改，分别放在对应的目录下面(主要是根据端口号)

port 7001  #端口
cluster-enabled yes #启用集群模式
cluster-config-file nodes.conf
cluster-node-timeout 5000 #超时时间
appendonly yes
daemonize yes #后台运行
protected-mode no #非保护模式
pidfile  /var/run/redis_7001.pid

#如果要设置密码需要增加如下配置：
#requirepass xxx (设置redis访问密码)

#masterauth xxx (设置集群节点间访问密码，跟上面一致)

注意如果配置了password，后面使用redis-cli 创建集群的时候需要添加参数./redis-cli -a xxx

3，启动6个节点

./redis-server ../redis-cluster/7001/redis.conf
./redis-server ../redis-cluster/7002/redis.conf
  ……
./redis-server ../redis-cluster/7006/redis.conf

4，启动集群

./redis-cli -a xxx --cluster create 192.168.2.40:7001 192.168.2.40:7002 192.168.2.40:7003 192.168.2.40:7004 192.168.2.40:7005 192.168.2.40:7006 --cluster-replicas 1

启动成功后显示如下信息：

>>> Performing hash slots allocation on 6 nodes...
Master[0] -> Slots 0 - 5460
Master[1] -> Slots 5461 - 10922
Master[2] -> Slots 10923 - 16383
Adding replica 192.168.2.40:7004 to 192.168.2.40:7001
Adding replica 192.168.2.40:7005 to 192.168.2.40:7002
Adding replica 192.168.2.40:7006 to 192.168.2.40:7003
>>> Trying to optimize slaves allocation for anti-affinity
[WARNING] Some slaves are in the same host as their master
M: 191c645200a8b4d267f71e3354c8248dbb533dde 192.168.2.40:7001
   slots:[0-5460] (5461 slots) master
M: 400a08d4e5a534c1b609988105d3e045395fbd12 192.168.2.40:7002
   slots:[5461-10922] (5462 slots) master
M: 684f6aa0fbccda295ce6818a8c01ee7255a7b002 192.168.2.40:7003
   slots:[10923-16383] (5461 slots) master
S: f2701549ae98315b432d73b49d139ee77d5685b4 192.168.2.40:7004
   replicates 684f6aa0fbccda295ce6818a8c01ee7255a7b002
S: 9fdc1e375436767ab815cbddd3df674f3bc2ca99 192.168.2.40:7005
   replicates 191c645200a8b4d267f71e3354c8248dbb533dde
S: e7742888ed85b37cff4a98e861e99bb16e8bae2c 192.168.2.40:7006
   replicates 400a08d4e5a534c1b609988105d3e045395fbd12
Can I set the above configuration? (type 'yes' to accept): yes
>>> Nodes configuration updated
>>> Assign a different config epoch to each node
>>> Sending CLUSTER MEET messages to join the cluster
Waiting for the cluster to join
....
>>> Performing Cluster Check (using node 192.168.2.40:7001)
M: 191c645200a8b4d267f71e3354c8248dbb533dde 192.168.2.40:7001
   slots:[0-5460] (5461 slots) master
   1 additional replica(s)
M: 684f6aa0fbccda295ce6818a8c01ee7255a7b002 192.168.2.40:7003
   slots:[10923-16383] (5461 slots) master
   1 additional replica(s)
S: 9fdc1e375436767ab815cbddd3df674f3bc2ca99 192.168.2.40:7005
   slots: (0 slots) slave
   replicates 191c645200a8b4d267f71e3354c8248dbb533dde
S: e7742888ed85b37cff4a98e861e99bb16e8bae2c 192.168.2.40:7006
   slots: (0 slots) slave
   replicates 400a08d4e5a534c1b609988105d3e045395fbd12
M: 400a08d4e5a534c1b609988105d3e045395fbd12 192.168.2.40:7002
   slots:[5461-10922] (5462 slots) master
   1 additional replica(s)
S: f2701549ae98315b432d73b49d139ee77d5685b4 192.168.2.40:7004
   slots: (0 slots) slave
   replicates 684f6aa0fbccda295ce6818a8c01ee7255a7b002
[OK] All nodes agree about slots configuration.
>>> Check for open slots...
>>> Check slots coverage...
[OK] All 16384 slots covered.

一些集群操作命令：

使用集群方式链接客户端： 

./redis-cli -c -h 127.0.0.1 -p 7002

在集群中查看集群信息：

cluster info
cluster nodes

关闭某个集群：

./redis-cli -c -h 127.0.0.1 -p 7001 shutdown

集群工具：create-cluster

在源码的utils下面 有个create-cluster.可用于集群的关闭与重启。

但是要编写一下里面的命令，因为你的目录与文件名可能和他的demo不一致。

主要修改 路径，文件名端口等信息。