IPv6 over IPv4 6to4 隧道（锐捷）

最新推荐文章于 2024-01-18 11:22:32 发布

HappyAston

最新推荐文章于 2024-01-18 11:22:32 发布

阅读量655

点赞数

文章标签：网络运维服务器

本文链接：https://blog.csdn.net/HappyAston/article/details/132550488

版权

拓扑：

实验目的

R1的Loo0和R5的Loo0接口实现通信

操作步骤

1.路由器配置各接口IP地址及路由

R1(config)#ipv6 unicast-routing 
R1(config)#int g0/1
R1(config-if-GigabitEthernet 0/1)#no switchport 
R1(config-if-GigabitEthernet 0/1)#ipv6 enable 
R1(config-if-GigabitEthernet 0/1)#ipv6 address 2002:1701:102:1::1:/64
R1(config-if-GigabitEthernet 0/1)#exit
R1(config)#ipv6 route ::/0 2002:1701:102:1::254

R2(config)#ipv6 unicast-routing 
R2(config)#int g0/1
R2(config-if-GigabitEthernet 0/1)#no switchport 
R2(config-if-GigabitEthernet 0/1)#ipv6 enable 
R2(config-if-GigabitEthernet 0/1)#ipv6 address 2002:1701:102:1::254/64
R2(config-if-GigabitEthernet 0/1)#exit
R2(config)#int g0/0
R2(config-if-GigabitEthernet 0/0)#no switchport 
R2(config-if-GigabitEthernet 0/0)#ip address 23.1.1.2 255.255.255.0
R2(config-if-GigabitEthernet 0/0)#exit
R2(config)#ip route 0.0.0.0 0.0.0.0 23.1.1.3

R3(config)#int g0/0
R3(config-if-GigabitEthernet 0/0)#no switchport 
R3(config-if-GigabitEthernet 0/0)#ip add 23.1.1.3 255.255.255.0
R3(config-if-GigabitEthernet 0/0)#exit
R3(config)#int g0/1
R3(config-if-GigabitEthernet 0/1)#no switchport 
R3(config-if-GigabitEthernet 0/1)#ip add 34.1.1.3 255.255.255.0
R3(config-if-GigabitEthernet 0/1)#exit

R4(config)#ipv6 unicast-routing 
R4(config)#int g0/0
R4(config-if-GigabitEthernet 0/0)#no switchport 
R4(config-if-GigabitEthernet 0/0)#ipv6 enable 
R4(config-if-GigabitEthernet 0/0)#ipv6 add 2002:2201:104:1::254/64
R4(config-if-GigabitEthernet 0/0)#exit
R4(config)#int g0/1
R4(config-if-GigabitEthernet 0/1)#no switchport 
R4(config-if-GigabitEthernet 0/1)#ip add 34.1.1.4 255.255.255.0
R4(config-if-GigabitEthernet 0/1)#exit
R4(config)#ip route 0.0.0.0 0.0.0.0 34.1.1.3

R5(config)#ipv6 unicast-routing 
R5(config)#int g0/0
R5(config-if-GigabitEthernet 0/0)#no sw
R5(config-if-GigabitEthernet 0/0)#no switchport 
R5(config-if-GigabitEthernet 0/0)#ipv6 enable
R5(config-if-GigabitEthernet 0/0)#ipv6 add 2002:2201:104:1::1/64
R5(config-if-GigabitEthernet 0/0)#exit
R5(config)#ipv6 route ::/0 2002:2201:104:1::254

2.R2和R4配置tunnel口及路由

R2(config)#int tunnel 0
R2(config-if-Tunnel 0)#tunnel mode ipv6ip 6to4
R2(config-if-Tunnel 0)#tunnel source g0/0
R2(config-if-Tunnel 0)#ipv6 enable
R2(config-if-Tunnel 0)#ipv6 address 2002:1701:102::1/64
R2(config-if-Tunnel 0)#exit
R2(config)#ipv6 route 2002::/16 tunnel 0

R4(config)#int tunnel 0
R4(config-if-Tunnel 0)#tunnel mode ipv6ip 6to4
R4(config-if-Tunnel 0)#tunnel source g0/1
R4(config-if-Tunnel 0)#ipv6 enable
R4(config-if-Tunnel 0)#ipv6 address 2002:2201:104::1/64
R4(config-if-Tunnel 0)#exit
R4(config)#ipv6 route 2002::/16 tunnel 0

3.测试连通信

R1#ping 2002:2201:104:1::1 source 2002:1701:102:1::1
Sending 5, 100-byte ICMP Echoes to 2002:2201:104:1::1, timeout is 2 seconds:
  < press Ctrl+C to break >
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 6/8/12 ms.
R1#trace 2002:2201:104:1::1 source 2002:1701:102:1::1
  < press Ctrl+C to break >
Tracing the route to 2002:2201:104:1::1

 1                   2002:1701:102:1::254     1 msec    1 msec   <1 msec
 2                   2002:1701:102:1::254    <1 msec    1 msec
                         2002:2201:104::1     2 msec
 3                     2002:2201:104:1::1     7 msec    6 msec    7 msec

R5#ping 2002:1701:102:1::1 source 2002:2201:104:1::1
Sending 5, 100-byte ICMP Echoes to 2002:1701:102:1::1, timeout is 2 seconds:
  < press Ctrl+C to break >
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 6/11/29 ms.
R5#trace 2002:1701:102:1::1 source 2002:2201:104:1::1 
  < press Ctrl+C to break >
Tracing the route to 2002:1701:102:1::1

 1                   2002:2201:104:1::254     2 msec   <1 msec   <1 msec
 2                   2002:2201:104:1::254    <1 msec   <1 msec   <1 msec
 3                       2002:1701:102::1     6 msec
                       2002:1701:102:1::1     6 msec    7 msec