CCIE-01-VLAN-Trunk

实验条件

网络拓朴

逻辑拓扑

物理拓扑

实验目的

1. SW1和SW2之间的E2/0-3配置为trunk，使用802.1q协议，不需要配置捆绑
2. 根据逻辑图和物理图标识，使得R1~R7之间的直连接口彼此都能ping通

开始配置

根据逻辑拓扑图，整理出一共需要配置VLAN14,15,23,24,35,46,57,67. 所以SW1和SW2上需要配置8个VLAN

配置SW1

SW1#conf t
SW1(config)#vlan 14,15,23,24,35,46,57,67
SW1(config-vlan)#exit
// 配置交换机Trunk口
SW1(config)#int range e2/0-3
SW1(config-if-range)#switchport trunk encapsulation dot1q 
SW1(config-if-range)#switchport mode trunk 
SW1(config-if-range)#exit

// 配置所有的接口类型为access,虽然都会默认，但最好都是明确的指定一下类型，不要配成协商的
SW1(config-if)#int range e0/0-3
SW1(config-if-range)#switchport mode access 
SW1(config-if-range)#int range e1/0-3
SW1(config-if-range)#switchport mode access 
SW1(config-if-range)#exit

SW1刷配置:
interface e0/0
switchport access vlan 15		//R1的E0/1
interface e0/1
switchport access vlan 23		//R2的E0/1
interface e0/2
switchport access vlan 23		//R3的E0/1
interface e0/3
switchport access vlan 24		//R4的E0/0
interface e1/0
switchport access vlan 14		//R4的E0/1
interface e1/1
switchport access vlan 15		//R5的E0/1
interface e1/2
switchport access vlan 67		//R6的E0/1
interface e1/3
switchport access vlan 67		//R7的E0/1

配置SW2

SW2#conf t
SW2(config)#vlan 14,15,23,24,35,46,57,67
SW2(config-vlan)#exit
// 配置交换机Trunk口
SW2(config)#int range e2/0-3
SW2(config-if-range)#switchport trunk encapsulation dot1q 
SW2(config-if-range)#switchport mode trunk 
SW2(config-if-range)#exit

// 配置所有的接口类型为access,虽然都会默认，但最好都是明确的指定一下类型，不要配成协商的
SW2(config-if)#int range e0/0-3
SW2(config-if-range)#switchport mode access 
SW2(config-if-range)#int range e1/0-3
SW2(config-if-range)#switchport mode access 
SW2(config-if-range)#exit

SW2刷配置:
interface e0/0
switchport access vlan 14		//R1的E0/2
interface e0/1
switchport access vlan 24		//R2的E0/2
interface e0/2
switchport access vlan 35		//R3的E0/2
interface e0/3
switchport access vlan 46		//R4的E0/2
interface e1/0
switchport access vlan 35		//R5的E0/0
interface e1/1
switchport access vlan 57		//R5的E0/2
interface e1/2
switchport access vlan 46		//R6的E0/2
interface e1/3
switchport access vlan 57		//R7的E0/2

检验证配置结果

R1-----R4

R1#ping 123.10.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 123.10.1.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
R1#

R1-----R5

R1#ping 123.10.1.6
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 123.10.1.6, timeout is 2 seconds:
.!!!!
Success rate is 80 percent (4/5), round-trip min/avg/max = 1/1/1 ms
R1#

R2-----R4

R2#ping 123.10.1.18 
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 123.10.1.18, timeout is 2 seconds:
.!!!!
Success rate is 80 percent (4/5), round-trip min/avg/max = 1/1/1 ms
R2#

R2-----R3

R2#ping 123.10.1.10
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 123.10.1.10, timeout is 2 seconds:
.!!!!
Success rate is 80 percent (4/5), round-trip min/avg/max = 1/1/1 ms
R2#

R3-----R5

R5#ping 123.10.1.13
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 123.10.1.13, timeout is 2 seconds:
.!!!!
Success rate is 80 percent (4/5), round-trip min/avg/max = 1/1/1 ms
R5#

R5-----R7

R5#ping 123.10.1.30
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 123.10.1.30, timeout is 2 seconds:
.!!!!
Success rate is 80 percent (4/5), round-trip min/avg/max = 1/1/1 ms
R5#

R7-----R6

R7#ping 123.10.1.25
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 123.10.1.25, timeout is 2 seconds:
.!!!!
Success rate is 80 percent (4/5), round-trip min/avg/max = 1/1/1 ms
R7#

R6-----R4

R6#ping  123.10.1.21
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 123.10.1.21, timeout is 2 seconds:
.!!!!
Success rate is 80 percent (4/5), round-trip min/avg/max = 1/1/1 ms
R6#

都可以通了、