上个ensp实验只发了配置，这次是命令条目

---

前言

上次没来的及法命令条目，只来得及发了配置，今天补上

一、实验及需求

要求按照拓扑图配置相关命令使得图中所有终端能够网络互通。
（1）MSTP+链路聚合：在SW1和SW2之间配置链路聚合，要求正常情况下有2条链路活跃、一条链路备份。常情况下各VLAN流量路径要求：VLAN10:SW3->SW2->R1；VLAN20:SW3->SW1->R1
（2）VRRP：正常情况下要求VLAN10的Master为SW2；VLAN20的Master为SW1
（3）DHCP：R3为DHCP中继代理，R2为DHCP服务器，为PC4、PC5提供动态分配IP服务。
（4）按照拓扑图中的要求在各三层交换机和路由器上配置路由，使得所有PC终端能够网络互通(10分)。
（5）NAT：使用EasyIp进行转换使得Client1能够使用R1的外网口IP访问外网；并使用NAT-Server使得Client1访问Server1的web服务时能够使用目标网址23.0.0.3/24的8080端口进行访问

二、命令

1、R1

<Huawei>undo terminal monitor 
Info: Current terminal monitor is off.
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]user-interface console 0
[Huawei-ui-console0]idle-timeout 0 0
[Huawei-ui-console0]q
[Huawei]int g0/0/0
[Huawei-GigabitEthernet0/0/0]ip add 10.0.0.1 24
[Huawei-GigabitEthernet0/0/0]int g0/0/1
[Huawei-GigabitEthernet0/0/1]ip add 11.0.0.1 24
[Huawei-GigabitEthernet0/0/1]int g0/0/2
[Huawei-GigabitEthernet0/0/2]ip add 12.0.0.1 24
[Huawei-GigabitEthernet0/0/2]q
[Huawei]ospf
[Huawei-ospf-1]area 0
[Huawei-ospf-1-area-0.0.0.0]net 10.0.0.0 0.0.0.255
[Huawei-ospf-1-area-0.0.0.0]net 11.0.0.0 0.0.0.255
[Huawei-ospf-1-area-0.0.0.0]net 12.0.0.0 0.0.0.255
[Huawei-ospf-1-area-0.0.0.0]q
[Huawei-ospf-1]q
[Huawei]acl number 3000  
[Huawei-acl-adv-3000] rule 5 permit ip source 192.168.10.0 0.0.0.255 
[Huawei-acl-adv-3000]int g0/0/2
[Huawei-GigabitEthernet0/0/2]nat outbound 3000

2、R2

<Huawei>undo terminal monitor 
Info: Current terminal monitor is off.
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]user-interface console 0
[Huawei-ui-console0]idle-timeout 0 0
[Huawei-ui-console0]int g0/0/0
[Huawei-GigabitEthernet0/0/0]ip add 12.0.0.2 24
[Huawei-GigabitEthernet0/0/0]int g0/0/1
[Huawei-GigabitEthernet0/0/1]ip add 23.0.0.2 24
[Huawei-GigabitEthernet0/0/1]int g0/0/2
[Huawei-GigabitEthernet0/0/2]ip add 24.0.0.2 24
[Huawei-GigabitEthernet0/0/2]q
[Huawei]ospf
[Huawei-ospf-1]area 0
[Huawei-ospf-1-area-0.0.0.0]net 12.0.0.0 0.0.0.255
[Huawei-ospf-1-area-0.0.0.0]q
[Huawei-ospf-1]import-route rip 1 type 1 cost 1	
[Huawei-ospf-1]default-route-advertise always
[Huawei-ospf-1]import-route static
[Huawei-ospf-1]q
[Huawei]rip 1
[Huawei-rip-1]v 2
[Huawei-rip-1]undo summary 
[Huawei-rip-1]net 23.0.0.0
[Huawei-rip-1]import-route ospf 1 cost 14
[Huawei-rip-1]default-route originate
[Huawei-rip-1]q
[Huawei]dhcp enable
Info: The operation may take a few seconds. Please wait for a moment.done.
[Huawei]ip pool 1
Info: It's successful to create an IP address pool.
[Huawei-ip-pool-1]gateway-list 192.168.40.1
[Huawei-ip-pool-1]net 192.168.40.0 mask 255.255.255.0
[Huawei-ip-pool-1]dns-list 8.8.8.8
[Huawei-ip-pool-1]lease day 10
[Huawei-ip-pool-1]int g0/0/1
[Huawei-GigabitEthernet0/0/1]dhcp select glo
[Huawei-GigabitEthernet0/0/1]q
[Huawei]ip route-static 192.168.30.0 24 24.0.0.4
[Huawei]ip route-static 192.168.40.0 24 23.0.0.1

3、R3

<Huawei>undo terminal monitor 
Info: Current terminal monitor is off.
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]user-interface console 0
[Huawei-ui-console0]idle-timeout 0 0
[Huawei-ui-console0]int g0/0/0
[Huawei-GigabitEthernet0/0/0]ip add 23.0.0.1 24
[Huawei-GigabitEthernet0/0/0]int g0/0/1
[Huawei-GigabitEthernet0/0/1]ip add 192.168.40.1 24
[Huawei-GigabitEthernet0/0/1]int g0/0/2
[Huawei-GigabitEthernet0/0/2]ip add 192.168.50.1 24
[Huawei-GigabitEthernet0/0/2]q
[Huawei]rip
[Huawei-rip-1]version 2
[Huawei-rip-1]undo summary 
[Huawei-rip-1]net 23.0.0.0
[Huawei-rip-1]net 192.168.40.0 
[Huawei-rip-1]net 192.168.50.0
[Huawei-rip-1]default-route originate
[Huawei-rip-1]q
[Huawei]dhcp enable
Info: The operation may take a few seconds. Please wait for a moment.done.
[Huawei]int g0/0/1
[Huawei-GigabitEthernet0/0/1]dhcp select relay
[Huawei-GigabitEthernet0/0/1]dhcp relay server-ip 23.0.0.2
[Huawei-GigabitEthernet0/0/1]q
[Huawei]int g0/0/0
[Huawei-GigabitEthernet0/0/0] nat server protocol tcp global 23.0.0.3 8080 insid
e 192.168.50.100 www

4、R4

<Huawei>undo terminal monitor 
Info: Current terminal monitor is off.
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]user-interface console 0
[Huawei-ui-console0]idle-timeout 0 0
[Huawei-ui-console0]int g0/0/0
[Huawei-GigabitEthernet0/0/0]ip add 192.168.30.1 24
[Huawei-GigabitEthernet0/0/0]int g0/0/2
[Huawei-GigabitEthernet0/0/2]ip add 24.0.0.4 24
[Huawei-GigabitEthernet0/0/2]q
[Huawei]ip route-static 0.0.0.0 0 24.0.0.2

5、LSW1

<Huawei>undo terminal monitor 
Info: Current terminal monitor is off.
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]user-interface console 0
[Huawei-ui-console0]idle-timeout 0 0
[Huawei-ui-console0]q
[Huawei]vlan bat 10 20 100
Info: This operation may take a few seconds. Please wait for a moment...done.
[Huawei]int g0/0/1
[Huawei-GigabitEthernet0/0/1]port link-type access
[Huawei-GigabitEthernet0/0/1]port default vlan20
[Huawei-GigabitEthernet0/0/1]int g0/0/5
[Huawei-GigabitEthernet0/0/5]port link-type access
[Huawei-GigabitEthernet0/0/5]port default vlan 20
[Huawei-GigabitEthernet0/0/5]q
[Huawei]stp mode mstp
[Huawei]stp region-configuration
[Huawei-mst-region]region-name huawei
[Huawei-mst-region]revision-level 1
[Huawei-mst-region]instance 1 vlan 10
[Huawei-mst-region]instance 2 vlan 20
[Huawei-mst-region]active region-configuration
Info: This operation may take a few seconds. Please wait for a moment...done.
[Huawei-mst-region]q
[Huawei]stp instance 2 root primary
[Huawei]stp instance 1 root secondary
[Huawei]int vlan 20
[Huawei-Vlanif20]vrrp vrid 20 virtual-ip 192.168.20.1
[Huawei-Vlanif20]vrrp vrid 20 priority 105
[Huawei-Vlanif20]vrrp vrid 20 track int g0/0/5
[Huawei-Vlanif20]int vlan 10
[Huawei-Vlanif10]vrrp vrid 10 virtual-ip 192.168.10.1
[Huawei-Vlanif10]q
[Huawei]int vlan 20
[Huawei-Vlanif20]ip add 192.168.20.10 24
[Huawei-Vlanif20]int vlan 10
[Huawei-Vlanif10]ip add 192.168.10.10 24
[Huawei-Vlanif10]int vlan 100
[Huawei-Vlanif100]ip add 10.0.0.10 24
[Huawei-Vlanif100]q
[Huawei]lacp priority 1000
[Huawei]int Eth-Trunk1
[Huawei-Eth-Trunk1]bpdu enable	
[Huawei-Eth-Trunk1]mode lacp-static
[Huawei-Eth-Trunk1]q
[Huawei]int g0/0/2
[Huawei-GigabitEthernet0/0/2]eth-trunk 1
Info: This operation may take a few seconds. Please wait for a moment...done.
[Huawei-GigabitEthernet0/0/2]int g0/0/3
[Huawei-GigabitEthernet0/0/3]eth-trunk 1
Info: This operation may take a few seconds. Please wait for a moment...done.
[Huawei-GigabitEthernet0/0/3]int g0/0/4
[Huawei-GigabitEthernet0/0/4]eth-trunk 1
Info: This operation may take a few seconds. Please wait for a moment...done.
[Huawei-GigabitEthernet0/0/4]int eth-trunk 1
[Huawei-Eth-Trunk1]max active-linknumber 2
[Huawei-Eth-Trunk1]port link-type trunk
[Huawei-Eth-Trunk1]port trunk allow-pass vlan all
[Huawei-Eth-Trunk1]q
[Huawei]ospf
[Huawei-ospf-1]area 0
[Huawei-ospf-1-area-0.0.0.0]net 10.0.0.0 0.0.0.255
[Huawei-ospf-1-area-0.0.0.0]net 192.168.10.0 0.0.0.255
[Huawei-ospf-1-area-0.0.0.0]net 192.168.20.0 0.0.0.255

6、LSW2

<Huawei>undo terminal monitor 
Info: Current terminal monitor is off.
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]user-interface console 0
[Huawei-ui-console0]idle-timeout 0 0
[Huawei-ui-console0]q
[Huawei]vlan bat 10 20 100
Info: This operation may take a few seconds. Please wait for a moment...done.
[Huawei]int g0/0/1
[Huawei-GigabitEthernet0/0/1]port link-type access
[Huawei-GigabitEthernet0/0/1]port default vlan 10
[Huawei-GigabitEthernet0/0/1]int g0/0/5
[Huawei-GigabitEthernet0/0/5]port link-type access
[Huawei-GigabitEthernet0/0/5]port default vlan 100
[Huawei-GigabitEthernet0/0/5]q
[Huawei]stp mode mstp
[Huawei]stp region-configuration
[Huawei-mst-region]region-name huawei
[Huawei-mst-region]revision-level 1
[Huawei-mst-region]instance 1 vlan 10
[Huawei-mst-region]instance 2 vlan 20
[Huawei-mst-region]active region-configuration
Info: This operation may take a few seconds. Please wait for a moment...done.
[Huawei-mst-region]q
[Huawei]stp instance 1 root primary
[Huawei]stp instance 2 root secondary
[Huawei]int vlan 10
[Huawei-Vlanif10]vrrp vrid 10 vir 192.168.10.1
[Huawei-Vlanif10]vrrp vrid 10 pri 105
[Huawei-Vlanif10]vrrp vrid 10 track int g0/0/5
[Huawei-Vlanif10]int vlan 20
[Huawei-Vlanif20]vrrp vrid 20 vir 192.168.20.1
[Huawei-Vlanif20]q
[Huawei]int vlan 10
[Huawei-Vlanif10]ip add 192.168.10.20 24
[Huawei-Vlanif10]int vlan 20
[Huawei-Vlanif20]ip add 192.168.20.20 24
[Huawei-Vlanif20]int vlan 100
[Huawei-Vlanif100]ip add 11.0.0.20 24
[Huawei-Vlanif100]q
[Huawei]lacp pri 1000
[Huawei]int eth-tr 1
[Huawei-Eth-Trunk1]bpdu enable
[Huawei-Eth-Trunk1]mode lacp-static
[Huawei-Eth-Trunk1]q
[Huawei]int g0/0/2
[Huawei-GigabitEthernet0/0/2]eth-tr 1
Info: This operation may take a few seconds. Please wait for a moment...done.
[Huawei-GigabitEthernet0/0/2]int g0/0/3
[Huawei-GigabitEthernet0/0/3]eth-tr 1
Info: This operation may take a few seconds. Please wait for a moment...done.
[Huawei-GigabitEthernet0/0/3]int g0/0/4
[Huawei-GigabitEthernet0/0/4]eth-tr 1
Info: This operation may take a few seconds. Please wait for a moment...done.
[Huawei-GigabitEthernet0/0/4]q
[Huawei]int eth-trunk 1
[Huawei-Eth-Trunk1]max active-linknumber 2
[Huawei-Eth-Trunk1]port link-type trunk
[Huawei-Eth-Trunk1]port trunk allow-pass vlan all
[Huawei-Eth-Trunk1]q
[Huawei]ospf
[Huawei-ospf-1]area 0
[Huawei-ospf-1-area-0.0.0.0]net 11.0.0.0 0.0.0.255
[Huawei-ospf-1-area-0.0.0.0]net 192.168.10.0 0.0.0.255
[Huawei-ospf-1-area-0.0.0.0]net 192.168.20.0 0.0.0.255

7、LSW3

<Huawei>undo terminal monitor 
Info: Current terminal monitor is off.
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]user-interface console 0
[Huawei-ui-console0]idle-timeout 0 0
[Huawei-ui-console0]q
[Huawei]vlan bat 10 20
Info: This operation may take a few seconds. Please wait for a moment...done.
[Huawei]int e0/0/1
[Huawei-Ethernet0/0/1]port link-type access
[Huawei-Ethernet0/0/1]port default vlan 10
[Huawei-Ethernet0/0/1]int e0/0/2
[Huawei-Ethernet0/0/2]port link-type access
[Huawei-Ethernet0/0/2]port default vlan 20
[Huawei-Ethernet0/0/2]int e0/0/3
[Huawei-Ethernet0/0/3]port link-type access
[Huawei-Ethernet0/0/3]port default vlan 10
[Huawei-Ethernet0/0/3]int g0/0/1
[Huawei-GigabitEthernet0/0/1]port link-type access
[Huawei-GigabitEthernet0/0/1]port default vlan 20
[Huawei-GigabitEthernet0/0/1]int g0/0/2
[Huawei-GigabitEthernet0/0/2]port link-type access
[Huawei-GigabitEthernet0/0/2]port default vlan 10
[Huawei-GigabitEthernet0/0/2]q
[Huawei]stp mode mstp
[Huawei]stp region-configuration
[Huawei-mst-region]region-name huawei
[Huawei-mst-region]revision-level 1
[Huawei-mst-region]instance 1 vlan 10
[Huawei-mst-region]instance 2 vlan 20
[Huawei-mst-region]active region-configuration
Info: This operation may take a few seconds. Please wait for a moment...done.

三、需求5的结果

总结

也就LSW1配的多了点，其他问题不大。
因为本来写的是简写，特地换成全写，所以花了点时间，所以上一篇没有写命令，今天补上。