R1
[r1]int g0/0/1.2
[r1-GigabitEthernet0/0/1.2]dot1q termination vid 3
[r1-GigabitEthernet0/0/1.2]arp broadcast enable
[r1-GigabitEthernet0/0/1.2]q
[r1]int g0/0/1.3
[r1-GigabitEthernet0/0/1.3]dot1q termination vid 4
[r1-GigabitEthernet0/0/1.3]arp broadcast enable
[r1]dhcp enable
[r1]ospf 1
[r1-ospf-1]display this
[V200R003C00]
#
ospf 1 router-id 1.1.1.1
area 0.0.0.0
network 192.168.1.1 0.0.0.0
network 192.168.1.65 0.0.0.0
network 192.168.1.81 0.0.0.0
network 192.168.1.97 0.0.0.0
#
return
[r1-ospf-1]q
[r1]display ip interface brief
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
The number of interface that is UP in Physical is 6
The number of interface that is DOWN in Physical is 1
The number of interface that is UP in Protocol is 5
The number of interface that is DOWN in Protocol is 2
Interface IP Address/Mask Physical Protocol
GigabitEthernet0/0/0 192.168.1.1/26 up up
GigabitEthernet0/0/1 unassigned up down
GigabitEthernet0/0/1.1 192.168.1.65/28 up up
GigabitEthernet0/0/1.2 192.168.1.81/28 up up
GigabitEthernet0/0/1.3 192.168.1.97/28 up up
GigabitEthernet0/0/2 unassigned down down
NULL0 unassigned up up(s)
[r1]display ip routing-table protocol ospf
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Public routing table : OSPF
Destinations : 2 Routes : 2
OSPF routing table status : <Active>
Destinations : 2 Routes : 2
Destination/Mask Proto Pre Cost Flags NextHop Interface
192.168.1.128/27 OSPF 10 2 D 192.168.1.2 GigabitEthernet
0/0/0
192.168.1.160/27 OSPF 10 2 D 192.168.1.2 GigabitEthernet
0/0/0
OSPF routing table status : <Inactive>
Destinations : 0 Routes : 0
[r1]dhcp enable
[r1]ip pool 1
[r1-ip-pool-1]network 192.168.1.64 mask 28
[r1-ip-pool-1]gateway-list 192.168.1.65
[r1-ip-pool-1]q
[r1]ip pool 2
[r1-ip-pool-2]network 192.168.1.80 mask 28
[r1-ip-pool-2]gateway-list 192.168.1.81
[r1-ip-pool-2]q
[r1]int g0/0/1.1
[r1-GigabitEthernet0/0/1.1]dhcp select global
[r1-GigabitEthernet0/0/1.1]int g0/0/1.2
[r1-GigabitEthernet0/0/1.2]dhcp select global
[r1-GigabitEthernet0/0/1.2]display current-configuration
[V200R003C00]
#
sysname r1
#
snmp-agent local-engineid 800007DB03000000000000
snmp-agent
#
clock timezone China-Standard-Time minus 08:00:00
#
portal local-server load portalpage.zip
#
drop illegal-mac alarm
#
set cpu-usage threshold 80 restore 75
#
dhcp enable
#
ip pool 1
gateway-list 192.168.1.65
network 192.168.1.64 mask 255.255.255.240
#
ip pool 2
gateway-list 192.168.1.81
network 192.168.1.80 mask 255.255.255.240
[r1]acl 3000
[r1-acl-adv-3000]rule deny ip source 192.168.1.64 0.0.0.15 destination 1.1.1.3 0
.0.0.0
[r1-acl-adv-3000]q
[r1]int g0/0/1.1
[r1-GigabitEthernet0/0/1.1]traffic-filter inbound acl 3000
[r1-GigabitEthernet0/0/1.1]q
[r1]
LSP
[ISP]int g0/0/0
[ISP-GigabitEthernet0/0/0]ip address 23.1.1.2 24
[ISP-GigabitEthernet0/0/1]ip address 1.1.1.1 24
R2
[r2]int g 0/0/2.1
[r2-GigabitEthernet0/0/2.1]dot1q termination vid 2
[r2-GigabitEthernet0/0/2.1]arp broadcast enable
[r2-GigabitEthernet0/0/2.1]int g0/0/2.2
[r2-GigabitEthernet0/0/2.2]dot1q termination vid 3
[r2-GigabitEthernet0/0/2.2]arp broadcast enable
[r2-ospf-1]display this
[V200R003C00]
#
ospf 1 router-id 2.2.2.2
area 0.0.0.0
network 192.168.1.2 0.0.0.0
network 192.168.1.129 0.0.0.0
network 192.168.1.161 0.0.0.0
#
return
[r2-ospf-1]display ip routing-table protocol ospf
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Public routing table : OSPF
Destinations : 3 Routes : 3
OSPF routing table status : <Active>
Destinations : 3 Routes : 3
Destination/Mask Proto Pre Cost Flags NextHop Interface
192.168.1.64/28 OSPF 10 2 D 192.168.1.1 GigabitEthernet
0/0/0
192.168.1.80/28 OSPF 10 2 D 192.168.1.1 GigabitEthernet
0/0/0
192.168.1.96/28 OSPF 10 2 D 192.168.1.1 GigabitEthernet
0/0/0
OSPF routing table status : <Inactive>
Destinations : 0 Routes : 0
[r2-ospf-1]dis
[r2-ospf-1]display ip
[r2-ospf-1]display ip ro
[r2-ospf-1]
Please check whether system data has been changed, and save data in time
Configuration console time out, please press any key to log on
[r2]dhcp enable
[r2]ip pool 2
[r2-ip-pool-2]network 192.168.1.128 mask 27
[r2-ip-pool-2]gateway-list 192.168.1.129
[r2-ip-pool-2]q
[r2]ip pool 3
[r2-ip-pool-3]network 192.168.1.160 mask 27
[r2-ip-pool-3]gateway-list 192.168.1.161
[r2-ip-pool-3]q
[r2]int g0/0/2.1
[r2-GigabitEthernet0/0/2.1]dhcp select global
[r2-GigabitEthernet0/0/2.1]int g0/0/2.2
[r2-GigabitEthernet0/0/2.2]dhcp select global
[r2-GigabitEthernet0/0/2.2]q
[r2]acl 2000
[r2-acl-basic-2000]rule permit source 192.168.1.0 0.0.0.255
[r2-acl-basic-2000]q
[r2]int g0/0/1
[r2-GigabitEthernet0/0/1]nat outbound 2000
[r2-GigabitEthernet0/0/1]q
[r2]ip route-static 0.0.0.0 0 23.1.1.2
[r2]int g0/0/1
[r2-GigabitEthernet0/0/1]nat server protocol tcp global current-interface 23 inside 192.168.1.98 telnet
Warning:The port 23 is well-known port. If you continue it may cause function fa
ilure.
Are you sure to continue?[Y/N]:y
[r2-GigabitEthernet0/0/1]q
[r2]acl 3000
[r2-acl-adv-3000]rule deny tcp source 1.1.1.2 0 destination-port eq telnet
[r2-acl-adv-3000]q
[r2]int g0/0/1
[r2-GigabitEthernet0/0/1]traffic-filter inbound acl 3000
[r2-GigabitEthernet0/0/1]q
SW1
[LSW1]vlan 2
[LSW1-vlan2]int g0/0/2
[LSW1-GigabitEthernet0/0/2]port link-type access
[LSW1-GigabitEthernet0/0/2]port default
[LSW1-GigabitEthernet0/0/2]port default vlan 2
[LSW1-GigabitEthernet0/0/2]q
[LSW1]int g0/0/1
[LSW1-GigabitEthernet0/0/1]port link-type trunk
[LSW1-GigabitEthernet0/0/1]port trunk allow-pass vlan 2 3 4
[LSW1-GigabitEthernet0/0/1]q
[LSW1]display vlan
The total number of vlans is : 2
--------------------------------------------------------------------------------
U: Up; D: Down; TG: Tagged; UT: Untagged;
MP: Vlan-mapping; ST: Vlan-stacking;
#: ProtocolTransparent-vlan; *: Management-vlan;
--------------------------------------------------------------------------------
VID Type Ports
--------------------------------------------------------------------------------
1 common UT:GE0/0/1(U) GE0/0/3(U) GE0/0/4(U) GE0/0/5(D)
GE0/0/6(D) GE0/0/7(D) GE0/0/8(D) GE0/0/9(D)
GE0/0/10(D) GE0/0/11(D) GE0/0/12(D) GE0/0/13(D)
GE0/0/14(D) GE0/0/15(D) GE0/0/16(D) GE0/0/17(D)
GE0/0/18(D) GE0/0/19(D) GE0/0/20(D) GE0/0/21(D)
GE0/0/22(D) GE0/0/23(D) GE0/0/24(D)
2 common UT:GE0/0/2(U)
TG:GE0/0/1(U)
VID Status Property MAC-LRN Statistics Description
--------------------------------------------------------------------------------
1 enable default enable disable VLAN 0001
2 enable default enable disable VLAN 0002
[LSW1] User interface con0 is available
Please Press ENTER.
[LSW1]vlan batch 2 3 4
[LSW1]display vlan
The total number of vlans is : 4
--------------------------------------------------------------------------------
U: Up; D: Down; TG: Tagged; UT: Untagged;
MP: Vlan-mapping; ST: Vlan-stacking;
#: ProtocolTransparent-vlan; *: Management-vlan;
--------------------------------------------------------------------------------
VID Type Ports
--------------------------------------------------------------------------------
1 common UT:GE0/0/1(U) GE0/0/3(U) GE0/0/4(U) GE0/0/5(D)
GE0/0/6(D) GE0/0/7(D) GE0/0/8(D) GE0/0/9(D)
GE0/0/10(D) GE0/0/11(D) GE0/0/12(D) GE0/0/13(D)
GE0/0/14(D) GE0/0/15(D) GE0/0/16(D) GE0/0/17(D)
GE0/0/18(D) GE0/0/19(D) GE0/0/20(D) GE0/0/21(D)
GE0/0/22(D) GE0/0/23(D) GE0/0/24(D)
2 common UT:GE0/0/2(U)
TG:GE0/0/1(U)
3 common TG:GE0/0/1(U)
4 common TG:GE0/0/1(U)
VID Status Property MAC-LRN Statistics Description
--------------------------------------------------------------------------------
1 enable default enable disable VLAN 0001
2 enable default enable disable VLAN 0002
3 enable default enable disable VLAN 0003
4 enable default enable disable VLAN 0004
[LSW1]int g0/0/2
[LSW1-GigabitEthernet0/0/2]q
[LSW1]int g0/0/3
[LSW1-GigabitEthernet0/0/3]port link-type access
[LSW1-GigabitEthernet0/0/3]port default vlan 3
[LSW1-GigabitEthernet0/0/3]int g0/0/4
[LSW1-GigabitEthernet0/0/4]port link-type access
[LSW1-GigabitEthernet0/0/4]port default vlan 4
SW2
[LSW2]vlan batch 2 3
[LSW2]int g0/0/2
[LSW2-GigabitEthernet0/0/2]port link-type access
[LSW2-GigabitEthernet0/0/2]port default vlan 2
[LSW2-GigabitEthernet0/0/2]int g0/0/3
[LSW2-GigabitEthernet0/0/3]port link-type access
[LSW2-GigabitEthernet0/0/3]port default vlan 3
[LSW2-GigabitEthernet0/0/3]int g0/0/1
[LSW2-GigabitEthernet0/0/1]port link-type trunk
[LSW2-GigabitEthernet0/0/1]port trunk allow-pass vlan 2 3
telnet server
[telnet server]int g0/0/0
[telnet server-GigabitEthernet0/0/0]ip address 192.168.1.98 27
[telnet server]ospf 1 router-id 3.3.3.3
[telnet server-ospf-1]area 0
[telnet server-ospf-1-area-0.0.0.0]network 192.168.1.0 0.0.0.255
[telnet server]user-interface vty 0 4
[telnet server-ui-vty0-4]authentication-mode aaa
[telnet server-ui-vty0-4]q
[telnet server]aaa
[telnet server-aaa]local-user telnet password cipher 123456
Info: Add a new user.
[telnet server-aaa]local-user telnet privilege level 15
[telnet server-aaa]local-user telnet service-type telnet
[telnet server-aaa]q
test-2
<Huawei>sys
[Huawei]int g0/0/0
[Huawei-GigabitEthernet0/0/0]ip address 1.1.1.2 24
[Huawei-GigabitEthernet0/0/0]q
[Huawei]ip route-static 0.0.0.0 0 1.1.1.1
test-1
[Huawei]int g0/0/0
[Huawei-GigabitEthernet0/0/0]ip address 1.1.1.4 24
[Huawei-GigabitEthernet0/0/0]q
[Huawei]ip route-static 0.0.0.0 0 1.1.1.1
测试
459
被折叠的 条评论
为什么被折叠?
到【灌水乐园】发言
