eston电源中英文对照

0低伏总线电压低于低浮阈值。　　

1低负荷总线电压低于低负荷阈值。　　

2高伏总线电压高于浮动阈值高。　　

3高负载总线电压高于高负荷阈值。　　

4整流器整流失败一个或多个失败　　

5多个整流器整流失败 不止一个整流器整流已经失败了。

6整流器审稿失去了 失去了通信与一个或多个整流器。

7多个整流器审稿失去 不止一个整流器已经失去了连接。

8局部交流失败 一个或多个阶段已经失败了　　

9 交流失败 系统交流已经失败了　　

10系统过载系统没有足够的能力负荷　　

11负载保险丝失败 负载保险丝熔断　　

12电源保险丝熔断 电池熔断器已经失败了　　

13个电池测试失败 电池测试过程失败　　

14个MOV失败了MOV(过载保护)已经失败了15 ACD风扇失败ACD风扇故障　　

16 LVD1断开LVD1(低电压断开1)已断开连接　

17 LVD1失败一级低压脱离18 LVD1手动一级低压脱离是被设置为手动　　

19 LVD1特征错误报警激活IOB值时,SC100特性不匹配。　

20 LVD2断开LVD2(低电压断开2)已断开连接。　　

21 LVD2失败LVD2已经失败了。　　

22 LVD2手动LVD2已经设置为手动。

23 LVD2表征误差报警激活IOB值时,SC100特性不匹配。　

24传感器失败 一个输入传感器已经失败了。　　

25总线电压传感器失败测量的平均总线电压总是高于2.0v

26温度传感器失败 温度传感器超出输入的范围。　　

27个电流传感器失败任何电流输入映射的范围。　　

28电池温度低电池温度小于电池温度低阈值。　　

29日电池温度高电池温度超过电池温度高阈值。平衡系统

30 自动匹配 执行自动补偿。

31快速充电系统是执行一个快速充电电池测试电池测试

32电池测试 电池测试在进行　　

33辅助温度低 辅助温度小于辅助临时低阈值。

34辅助温度高　　辅助温度大于辅助临时高阈值。　　

35辅助温度传感器失败　　辅助温度传感器超出范围。　　

36在放电 电池在放电。　　

37硬件丢失 报警激活如果映射的输入或输出映射不存在。　　

38电池电流限制表明电池达到限流。　　

39蓄电池充电超过电流　　当前电流值大于或者等于2A

40整流器报警应激活如果负载电流小于2%的额定系统电流限制。　　

41整流器电流限制 这个报警应激活如果任何整流器在电流限制。　　

42在温度告警整流器应激活如果任何整流器在热调节。　　

43未知的硬件报警激活时未检测到任何RXP装置。　　

44待机模式报警激活当另一个控制器控制总线的RXP。　　

45交流相整流器失踪当一个或多个整流器被分配到一个交流阶段,他们中没有一个是注册。　

46交流高AC电压大于或等于交流高阈值。　　

47交流低交流电压小于或等于交流低阈值。　　

48关闭所有整流器所有矩形已经关闭了SC100。　

49配置错误　

50电池表 电池特性表征是在进步。　　

51电池特性误差　　百分比计算值之间的偏差和配置的值　　电池特性也超过20%。52电池特性　　失败　　电池特性是失败的。

  
  
0 Low Float The Bus Voltage is lower than the Low Float Threshold.
1 Low Load The Bus Voltage is lower than the Low Load Threshold.
2 High Float  The Bus Voltage is higher than the High Float Threshold.
3 High Load   The Bus Voltage is higher than the High Load Threshold.
4 Rectifier Fail  One or more rectifiers has failed
5 Multiple Rectifier Fail More than one rectifier has failed.
6 Rectifier Comms Lost Lost communications with one or more rectifiers.
7 Multiple Rectifier Comms Lost  More than one rectifier has lost comms.
8 Partial AC Fail One or more phases has failed
9 AC Fail System    AC has failed
10 System Overload The system does not have enough capacity
11 Load Fuse Fail The load fuse has failed
12 Battery Fuse Fail The battery fuse has failed
13 Battery Test Fail The battery test process has failed
14 MOV Fail The MOV (surge protection) has failed
15 ACD Fan Fail The ACD fan has failed
16 LVD1 Disconnected LVD1 (Low Voltage Disconnect 1) has disconnected
17 LVD1 Fail LVD1 has failed
18 LVD1 Manual LVD1 is has been set to Manual
19LVD1 Characterization Error Alarm activates when IOB and SC100 characterization values do not match.
20 LVD2 Disconnected LVD2 (Low Voltage Disconnect 2) has disconnected.
21 LVD2 Fail LVD2 has failed.
22 LVD2 Manual LVD2 has been set to Manual
23 LVD2 CharacterizationErrorAlarm activates when IOB and SC100 characterization values do not match.
24 Sensor Fail An input sensor has failed.
25 Bus Voltage Sensor Fail The average bus voltage as measured by the bus voltage sensor is more than 2.0V awaycorrected average rectifier output voltage
26 Temperature Sensor Fail Temperature sensor input is out of range.
27 Current Sensor Fail Any current input that is mapped is out of range.
28 Battery Temperature Low The Battery Temperature is less than the Battery Temperature Low Threshold.
29 Battery Temperature High The Battery Temperature is more than the Battery Temperature High Threshold.
30 Equalize The system is performing an equalize charge.
31 Fast Charge The system is performing a fast charge
32 Battery Test A Battery Test is in progress
33 Auxiliary Temperature Low Auxiliary Temperature is less than Aux Temp Low Threshold.
34 AuxiliaryTemperatureHighAuxiliary Temperature is more than Aux Temp High Threshold.
35 Auxiliary TemperatureSensor FailThe aux temp sensor input is out of range.
36 In Discharge The battery is discharging.
37 Missing Hardware Alarm activated if a mapped input or mapped output is not present.
38 Battery Current Limit Indicates Battery reaching current limit.
39 Battery Charge OverCurrentBattery Current is greater than or equal to [Battery Charge Over Current Threshold *Battery Capacity] or 2A, whichever is the greatest.
40 Rectifier No Load This alarm shall activate if load current is less than 2% of rated system current limit.
41 Rectifier Current Limit This alarm shall activate if any rectifier is in current limit.
42 Rectifier Over Temperature This alarm shall activate if any rectifier is in thermal turndown.
43 Unknown Hardware Alarm activates when any unrecognized RXP device is detected.
44 Standby Mode Alarm activates when another controller has control of the RXP bus.
45 AC Phase Rectifier Missing When one or more rectifiers are assigned to a AC phase and none of them is registered.
46 AC High The AC Voltage is greater than or equal to the AC High Threshold.
47 AC Low The AC Voltage is less than or equal to the AC Low Threshold.
48 All Rect Shutdown All rectifiers have been shutdown by SC100.
49 Config Error
50 Characterizing Battery A Battery Characterization is in progress.
51 BatteryCharacterizationError Thepercentagedeviation between the calculated values and the configured values ofbattery characterization is more than 20%.
52 BatteryCharacterizationFailBattery Characterization is failed.