安卓5.1源码 lcd驱动移植

最新推荐文章于 2024-05-15 15:29:04 发布

free_sz

最新推荐文章于 2024-05-15 15:29:04 发布

阅读量2.6k

点赞数

分类专栏： Android 文章标签：移植 kernel lk android

本文链接：https://blog.csdn.net/baidu_35904821/article/details/53926843

版权

Android 专栏收录该内容

24 篇文章 2 订阅

订阅专栏

Kernel部分：/kernel-3.10/drivers/misc/mediate/lcm

#define FRAME_WIDTH                                                                                             (720)
#define FRAME_HEIGHT                                                                                             (1280)  //分辨率修改
 
static structLCM_setting_table lcm_initialization_setting[] = {
         //初始化代码修改为p43厂商给的初始化代码；
}
 
static voidinit_lcm_registers(void)
{
         //寄存器函数删除掉；
}
 
static struct LCM_setting_tablelcm_sleep_out_setting[] = {
   //Sleep Out
   {0x11, 1, {0x00}},
   {REGFLAG_DELAY, 120, {}},
 
   // Display ON
   {0x29, 1, {0x00}},
   {REGFLAG_DELAY, 20, {}},
   {REGFLAG_END_OF_TABLE, 0x00, {}}
};
 
static struct LCM_setting_tablelcm_deep_sleep_mode_in_setting[] = {
   
   // Display off sequence
   {0x28, 1, {0x00}},
   {REGFLAG_DELAY, 20, {}},
 
   // Sleep Mode On
   {0x10, 1, {0x00}},
   {REGFLAG_DELAY, 120, {}},
   {REGFLAG_END_OF_TABLE, 0x00, {}}
};
 
static void lcm_get_params(LCM_PARAMS*params)
{
         memset(params,0, sizeof(LCM_PARAMS));
         params->type   = LCM_TYPE_DSI;
 
         params->width  = FRAME_WIDTH;
         params->height= FRAME_HEIGHT;
         //enable tearing-free
         params->dbi.te_mode                              =LCM_DBI_TE_MODE_VSYNC_ONLY;
         params->dbi.te_edge_polarity                 = LCM_POLARITY_RISING;
 
#if (LCM_DSI_CMD_MODE)
                   params->dsi.mode   = CMD_MODE;
#else
                   params->dsi.mode   =SYNC_PULSE_VDO_MODE; //SYNC_PULSE_VDO_MODE;//BURST_VDO_MODE;
         //params->dsi.mode   = BURST_VDO_MODE;
#endif
 
         //DSI
         /*Command mode setting */
         params->dsi.LANE_NUM                                     =LCM_FOUR_LANE;  //这句函数对应你的lcd修改
         params->dsi.data_format.format                      =LCM_DSI_FORMAT_RGB888;
 
         //videomode timing
         params->dsi.PS=LCM_PACKED_PS_24BIT_RGB888;
 	//前后阶参数查看datashift；
	params->dsi.vertical_sync_active                               = 10; //8; //2;
	params->dsi.vertical_backporch                                           = 20;//18;        //14;
	params->dsi.vertical_frontporch                                          = 10;//20;        //16;
 	params->dsi.vertical_active_line                                =FRAME_HEIGHT;
 	params->dsi.horizontal_sync_active                                   = 40;         //2;
	params->dsi.horizontal_backporch                                     =100;//120;     //60;         //42;
	params->dsi.horizontal_frontporch                                     = 80;//100;       //60;         //44;
	params->dsi.horizontal_active_pixel                                  = FRAME_WIDTH;
 
	params->dsi.PLL_CLOCK= 175;//208; 210      //查看datashift；
}
void lcm_display_on(void)
{
         //去掉这段函数；
}
static void lcm_init(void)
{
        
 
         SET_RESET_PIN(1);
         MDELAY(10);
         SET_RESET_PIN(0);
         MDELAY(10);
         SET_RESET_PIN(1);
         MDELAY(120);
   	 push_table(lcm_initialization_setting,sizeof(lcm_initialization_setting) / sizeof(struct LCM_setting_table), 1);
         (init_lcm_registers();
         lcm_display_on();) //去掉这两句；
   	LCD_DEBUG("uboot:boe_nt35521_lcm_init\n");
}
static structLCM_setting_table lcm_backlight_level_setting[] = {
         //去掉这段函数；
}
static voidlcm_setbacklight(unsigned int level)
{
         //去掉这段函数；
}
static unsigned int lcm_compare_id(void)
{
         //本函数最后返回了一个ID屏蔽掉这一句；
         return (ID == 0x9881)?1:0;
}