Linux下网卡的桥接 (Bridge mode)

最新推荐文章于 2024-09-23 19:09:08 发布

chuanzhilong

最新推荐文章于 2024-09-23 19:09:08 发布

阅读量3.6k

点赞数

分类专栏： Linux kernel

Linux kernel 专栏收录该内容

48 篇文章 3 订阅

订阅专栏

modprobe bridge

brctl addbr br0
#> ifconfig

eth0      Link encap:Ethernet HWaddr 00:CC:D0:99:EB:26
          inet6 addr: fe80::2b0:d0ff:fe99:eb26/64 Scope:Link
          UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1
          RX packets:86208855 errors:0 dropped:0 overruns:63 frame:0
          TX packets:77098217 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:3871506445 (3692.1 Mb) TX bytes:266311184 (253.9 Mb)
          Interrupt:5 Base address:0xec00

eth1      Link encap:Ethernet HWaddr 00:CC:03:D8:3A:1A
          inet6 addr: fe80::201:3ff:fed8:3a1a/64 Scope:Link
          UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1
          RX packets:77087614 errors:0 dropped:0 overruns:0 frame:0
          TX packets:85110321 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:264995582 (252.7 Mb) TX bytes:3672580334 (3502.4 Mb)
          Interrupt:9 Base address:0xec80

/etc/sysconfig/networking-scripts/ifcfg-eth0:

DEVICE=eth0
ONBOOT=yes
BOOTPROTO=static

/etc/sysconfig/networking-scripts/ifcfg-eth1:

DEVICE=eth1
ONBOOT=yes
BOOTPROTO=static

#> brctl addif br0 eth0
#> brctl addif br0 eth1
#> ip link set br0 up

#> ip addr add 10.1.1.18/16 brd + dev br0

#> route add default gw 10.1.1.1 dev br0

#> brctl show
bridge name bridge id          STP enabled interfaces
br0          8000.0030843e5aa2 no           eth0
                                             eth1

[桥接下防火墙设置]

#> tar -xzf ebtables-v2.0.6.tar.gz
#> cd ebtables-v2.0.6
#> make
#> install

#> ebtables -V
ebtables v2.0.6 (November 2003)

#> service iptables stop
#> chkconfig --level 35 iptables off

#> iptables -L
#> iptables -F INPUT
#> iptables -F OUTPUT
#> iptables -F FORWARD
#> iptables -F RH-Firewall-1-INPUT

/sbin/ebtables -A FORWARD -p IPv4 \--ip-source 10.2.0.0/16 -j DROP
/sbin/ebtables -A FORWARD -p IPv4 \--ip-source 10.7.0.0/16 -j DROP
/sbin/ebtables -A FORWARD -p IPv4 \--ip-source 10.4.0.0/16 -j DROP
/sbin/ebtables -A FORWARD -p IPv4 \--ip-source 10.5.0.0/16 -j DROP
/sbin/ebtables -A FORWARD -p IPv4 \--ip-source 10.6.0.0/16 -j DROP
/sbin/ebtables -A FORWARD -p IPv4 \--ip-source 10.1.0.0/16 -j DROP

/sbin/ebtables -I FORWARD 1 -p IPv4 \--ip-source 10.1.1.5 -j ACCEPT
/sbin/ebtables -I FORWARD 1 -p IPv4 \--ip-source 10.1.1.18 -j ACCEPT

/sbin/ebtables -I FORWARD 1 -p IPv4 \--ip-source 10.1.10.30 -j ACCEPT
/sbin/ebtables -I FORWARD 1 -p IPv4 \--ip-source 10.1.10.19 -j ACCEPT
/sbin/ebtables -I FORWARD 1 -p IPv4 \--ip-source 10.1.10.87 -j ACCEPT

转自：http://blog.chinaunix.net/uid-102511-id-2967735.html