(1) accidents are falling from the sky slow effort, motor falling from the sky and
electrical wire rope hoist motors are connected to the body member is disengaged, the motor is disengaged gourd body and are pressed loose screw connection, the connection is not secure due.
(2) Why is there a loose bolt connections after the accident analysis shows, 0.4kw child is screwed into the hoist motor body through one end of the double-headed snail accident? - On the flange. Another - end by a nut and spring washer child motor flange fixed connection even hoist body screw loosening the survey found mainly factory during assembly failed to tighten the bolts on the hoist end of the body, in use due to vibration. It accelerated the loose bolts not tightened, resulting effort together with bolts and fall to the ground together off from the wire rope pulling hoist body. This is the main cause of child motor falling.
(3) Spring washer fake, poor quality no flexibility, when tightening the nut and then loosen the nut, spring washers become flat washers, can hardly locking action. One of the reasons is caused by loose screw connections, wherein said accidents have together on this, and therefore, can not underestimate the role of a small washer.
(4) The reason this case is a factor in the accident as well as the motor bearings appears broken due to inferior quality in use. There are small pieces into the reduction gear when the small, not only will gear damage, but hindered by the ten gears, force limiters and a primary connection is not strong enough to promote increased loose bolts falling off caused by motor accidents.
Typical accident cases which are manufactured together, assembly quality control is lax, counterfeiting and other purchased parts supporting causes.
Causes of the accident has been following lessons:
(1) a slow drive through several reactive power dynamometer fall accident from the small fact that the manufacturer must attach great importance to the quality of products was assembled, strictly to restore credibility.
(2) The manufacturer must strictly good three foreign relations, namely the quality of purchased parts, the processing quality and the outer supporting quality, small spring washers gone and because of the specific energy.
(3) The user must periodically check various aspects of the motor, the functioning of the various parts, abnormal timely maintenance, eliminate hidden dangers.
(2) Why is there a loose bolt connections after the accident analysis shows, 0.4kw child is screwed into the hoist motor body through one end of the double-headed snail accident? - On the flange. Another - end by a nut and spring washer child motor flange fixed connection even hoist body screw loosening the survey found mainly factory during assembly failed to tighten the bolts on the hoist end of the body, in use due to vibration. It accelerated the loose bolts not tightened, resulting effort together with bolts and fall to the ground together off from the wire rope pulling hoist body. This is the main cause of child motor falling.
(3) Spring washer fake, poor quality no flexibility, when tightening the nut and then loosen the nut, spring washers become flat washers, can hardly locking action. One of the reasons is caused by loose screw connections, wherein said accidents have together on this, and therefore, can not underestimate the role of a small washer.
(4) The reason this case is a factor in the accident as well as the motor bearings appears broken due to inferior quality in use. There are small pieces into the reduction gear when the small, not only will gear damage, but hindered by the ten gears, force limiters and a primary connection is not strong enough to promote increased loose bolts falling off caused by motor accidents.
Typical accident cases which are manufactured together, assembly quality control is lax, counterfeiting and other purchased parts supporting causes.
Causes of the accident has been following lessons:
(1) a slow drive through several reactive power dynamometer fall accident from the small fact that the manufacturer must attach great importance to the quality of products was assembled, strictly to restore credibility.
(2) The manufacturer must strictly good three foreign relations, namely the quality of purchased parts, the processing quality and the outer supporting quality, small spring washers gone and because of the specific energy.
(3) The user must periodically check various aspects of the motor, the functioning of the various parts, abnormal timely maintenance, eliminate hidden dangers.
来自 “ ITPUB博客 ” ,链接:http://blog.itpub.net/30085872/viewspace-1675487/,如需转载,请注明出处,否则将追究法律责任。
转载于:http://blog.itpub.net/30085872/viewspace-1675487/