产 品 规 格 书
SPECIFICATION
TYPE:“HX”Electret Condenser Microphone
Part No. :EM-6027A
1. | 适用范围: Seope | 本规格书适用于驻极体式电容传声器 This spccification applies electret condenser microphone (E.C.M) |
2. | 型号: Model No. | EM-6027A |
3. | 使用条件: Operation Condition | |
3.1 环境温度 Temperature | -20~+70℃ | |
3.2 相对湿度 Rel,Humidity | 35%~85%RH | |
3.3 大气压力 Pressure | 86~106Kpa | |
3.4 环境噪声 Environmental Noise | 32dB (最大) 32dB (Maximum) | |
3.5 工作电压范围 Operation Voltage | 1~10VDC | |
3.6 接地方式: Earth | ⊙ | |
4. | 电性能 Electrical Characteristics | |
4.1 基准工作电压 StandardOperationVoltage | 3VDC | |
4.2 阻抗 Impedance | 2.2kΩ (最大) 2.2kΩ (Maximum) | |
4.3 消耗电流 Current Consumption | 0.5mA (最大) 0.5mA (Maximum) | |
4.4 灵敏度 Sensitivity | -36dB±2dB(0dB=1V/Pa,1KHz) -56dB±2dB(0dB=1V/μbar, 1KHz) Vs=4.5V R1=2.2kΩ | |
4.5 指向性 Directivity | 全指向性 Omni-directional | |
4.6 信噪比 S/N Ratio | 40dB(最小) 40dB(Minimum) |
WRTN | CHKD | APVD | DESCRIPTION |
|
|
|
|
|
|
|
|
3-2
TYPE:“XL” Electret Condenser Microphone
Part No. :EM-6027AP
| 4.7 测试电路图 Schematic Diagram Vs=2.0V ; R1=2.2kΩ; C=1uF
|
|
4.8 测试环境温度 Test Temperature 测试环境湿度 Rel.Humidity | 20℃±2℃
45%~65%RH | |
4.9 频率响应曲线 Frequency Response |
| |
5. | 机械性能 Mechanical Characteristics | |
5.1 尺寸 Dimension | ¢6.0±0.1×2.7±0.2 | |
5.2 重量 Mass | ≦0.3g | |
5.3 外形图 Dimensional Drawing
|
|
3-3
6. | 可靠性试验 Reliability Tests 试验后,置于20℃环境中恢复3小时,试验前后灵敏度的变化在±3dB以内。 The sensitivity to be within ±3dB of initial sensitivity affer 3 hours conditioning at 20℃. | |
6.1 振动试验 Vibration | 频率1 Frequency1 10Hz~55Hz 振幅 Amplitude ±0.15mm 频率2 Frequency2 55Hz~150Hz 加速度 Acceleration 20m/s 频率变化 Change of Frequency 1倍频程/分 1octave/min 3个方向,各2小时 2 hrs in each of 3 axes | |
6.2 冲击试验 Shocks | 脉冲波形 Pulse Shape 正弦半波 Half Sinusoidal 脉冲宽度 Puise Duration 11ms 加速度 Acceleration 150m/s2 冲击次数 Number of Jolts 3个方向,各10次 10 in each of 3 axes | |
6.3 高低温试验 Dry Heat/Cold | 70℃,72小时 -20℃,72小时 70℃ for 72hrs -20℃ for 72hrs | |
6.4 高温高湿 Damp Heat | 90%RH,+40℃,120小时 90%RH,+40℃ for 120hrs | |
6.5 温度交变试验 Temperature Cycles | -20℃←→25℃←→70℃ 10次 (2h)(1h)(2h)(1h)(2h) 10cycles | |
7. | 注意事项 Cautions | |
7.1 焊接型传声器的焊接,请使用20W以下的小型电烙铁。 The soldering copper of a smaller type of less than 20W shall be applied. | ||
7.2 焊接时铜箔表面温度应低于270℃. The temperaure of the working surface of the soldering copper shall be below 270℃. | ||
7.3 应把驻极体传声器固定在散热良好的装置台上进行焊接。 E.C.M shall be solderde fixed on the metal block (heat sink)which has the higher Radiation effects heat sink shall contact with each of E.C.M. | ||
7.4 每个焊点的焊接时间应在1~2秒之内。 The soldering time for each terminal shall be 1~2 sec. | ||
7.5 焊接后,各焊点不应出现砂眼现象。 The pin hole soldering shall be avoided. | ||
7.6 驻极体传声器容易受静电破坏,应采取防静电措施(焊接器具、工作台、操作人员人体应接地) E.C.M may easily destroyed by the static electricity,and the countermeasure for eliminating The staticelectricity (the ground for soldering copper,for worktable and for human body) shall be executed. |