T2080RDB: UBoot boot vxWorks SMP
3162412793@qq.com
技术交流QQ群:691976956
U-Boot 2015.01QorIQ-SDK-V1.8+g6ba8eed (Jun 14 2015 - 06:33:44)
CPU0: T2080E, Version: 1.1, (0x85380011)
Core: e6500, Version: 2.0, (0x80400120)
Clock Configuration:
CPU0:1799.820 MHz, CPU1:1799.820 MHz, CPU2:1799.820 MHz, CPU3:1799.820 MHz,
CCB:599.940 MHz,
DDR:933.310 MHz (1866.620 MT/s data rate) (Asynchronous), IFC:149.985 MHz
FMAN1: 699.930 MHz
QMAN: 299.970 MHz
PME: 599.940 MHz
L1: D-cache 32 KiB enabled
I-cache 32 KiB enabled
Reset Configuration Word (RCW):
00000000: 1207001b 15000000 00000000 00000000
00000010: 66150002 00000000 ec027000 c1000000
00000020: 00800000 00000000 00000000 000307fc
00000030: 00000000 00000000 00000000 00000004
Board: T2080RDB, Board rev: 0x01 CPLD ver: 0x03, boot from NOR vBank0
SERDES Reference Clocks:
SD1_CLK1=156.25MHZ, SD1_CLK2=100.00MHZ
SD2_CLK1=100.00MHZ, SD2_CLK2=100.00MHZ
I2C: ready
SPI: ready
DRAM: Initializing....using SPD
Detected UDIMM D3XP56082XL10AA
2 GiB left unmapped
4 GiB (DDR3, 64-bit, CL=13, ECC on)
DDR Chip-Select Interleaving Mode: CS0+CS1
VID: Could not find voltage regulator on I2C.
Warning: Adjusting core voltage failed.
Flash: 128 MiB
L2: 2 MiB enabled
Corenet Platform Cache: 512 KiB enabled
Using SERDES1 Protocol: 102 (0x66)
Using SERDES2 Protocol: 21 (0x15)
SEC0: RNG instantiated
NAND: 512 MiB
MMC: FSL_SDHC: 0
EEPROM: Invalid ID (ff ff ff ff)
PCIe1: Endpoint, undetermined, regs @ 0xfe240000
PCIe1: Bus 00 - 00
PCIe2: Root Complex, x2 gen2, regs @ 0xfe250000
02:00.0 - 1957:0808 - Processor
PCIe2: Bus 01 - 02
PCIe3: disabled
PCIe4: Root Complex, no link, regs @ 0xfe270000
PCIe4: Bus 03 - 03
In: serial
Out: serial
Err: serial
Net: Fman1: Uploading microcode version 106.4.15
PHY reset timed out
PHY reset timed out
FM1@DTSEC3, FM1@DTSEC4 [PRIME], FM1@TGEC1, FM1@TGEC2, FM1@TGEC3, FM1@TGEC4
Hit any key to stop autoboot: 3 2 0
=> setenv bootargs 'memac(2,0)host:vxWorks h=200.168.1.13 e=200.168.1.14 u=vxworks pw=vxworks f=0x0'
=> tftp vxWorks
Using FM1@DTSEC4 device
TFTP from server 200.168.1.13; our IP address is 200.168.1.14
Filename 'vxWorks'.
Load address: 0x1000000
Loading: *#################################################################
#################################################################
#################################################################
##################################
5.2 MiB/s
done
Bytes transferred = 3358176 (333de0 hex)
=> bootv
## Ethernet MAC address not copied to NV RAM
## Using bootline (@ 0x4200): memac(2,0)host:vxWorks h=200.168.1.13 e=200.168.1.14 u=vxworks pw=vxworks f=0x0
## Starting vxWorks at 0x00100000 ...
Target Name: vxTarget
0x82c3640 (tRootTask): kernelCpuEnableInternal: pExcStackBase : 0x82a5dd0
0x82c3640 (tRootTask): kernelCpuEnableInternal: pExcStackBase : 0x82a9430
0x82c3640 (tRootTask): usrEnableCpu: error when enabling additional CPU: 2
userEnableCpu: kernelCpuEnableInternal() failed
0x82c3640 (tRootTask): kernelCpuEnableInternal: pExcStackBase : 0x82aca90
0x82c3640 (tRootTask): Error: CPU2 must be enabled before CPU3
0x82c3640 (tRootTask): usrEnableCpu: error when enabling additional CPU: 3
userEnableCpu: kernelCpuEnableInternal() failed
Add0xing 82c36407342 ( symbols for standalone.
tRootTask): kernelCpuEnableInternal: pExcStackBase : 0x82b00f0
VxW0xorks82c3640
(CopyritRootTaskght 1984-): 2016usrEnableCpu: error wh Wind River Systems, en enabling additionalInc.
CPU: 4 CPU:
userEnableCpu: kernelCpuEnableInternalFreescale QorIQ T2080()
failed
Runtime Name: 0xVxWorks82c3640
( RutRootTaskntime Version:): kernelCpuEnableIntern6.9 SMPal: pExcStackBas
e : BSP version: 6.9/0
0x Created:82b3750
Apr 13 2016 20:00x8:2682c3640
(ED&R Politcy Mode: RootTaskDepl): oyedError: CPU
4 WDB Comm Type: must be WDB_COMM_ENDenabled bef
ore CPU W5DB:
Agent Disabled.
0x82c3640 (tRootTask): usrEnableCpu: error when enabling additional CPU: 5
userEnableCpu: kernelCpuEnableInternal() failed
0x82c3640 (): task dead
usrEnableCpu: error when enabling additional CPU: 7
userEnableCpu: kernelCpuEnableInternal() failed
->