HPE 3par SS7200 扩容步骤

本文详细介绍了HPE 3par SS7200存储系统的硬盘扩容步骤,包括添加驱动器许可证、运行健康检查、进入维护模式、安装新硬盘、连接线缆、承认硬件、退出维护模式,并在每个步骤后进行健康检查,确保系统稳定。

摘要生成于 C知道 ,由 DeepSeek-R1 满血版支持, 前往体验 >


 

- First create andadd the new Drive license (if under 48)

- use checkhealth tosee if 3PAR is OK

- Install the Cagewith the new Disks and Power On

- prepare the SASCable

- Cable the new Shelf as found in the "7000 Series StorageCabling Configuration Guide" (if online, one Node after the other and waitbetween) http://h20564.www2.hpe.com/hpsc/doc/public/display?docId=c04441589

- use showcage tocheck

- admithw (wait iffirmware is applied)

- showpd -c (waituntil all chunklets are initiaisized)

- use checkhealth tosee if 3PAR is OK

- use tunesys tostart leveling

开机步骤

Powering On the Storage System 2. 3. 4. 5. 6. Set the circuit breakers on the PDUs to the ON position. Set the switches on the power strips to the ON position. NOTE: Some power strips may not have power switches. Power on the service processor. Power on the drive enclosure PCMs. Power on the node enclosure PCMs. After approximately 10 minutes, allowing time for the system to boot and the cache batteries to charge, verify the status of the LEDs as described in "Verifying LED Status" (page 55).

指示灯

NOTE: If any module fault or disk drive LEDs are not green, do not proceed until the problem is resolved. figure 35 Bezel LEDs Table 7 Identifying Bezel LEDs 2 3 Pcnver indicator Module fault Disk drive status

 

Table 8 Identifying Disk Drive LEDs 2 Amber LED indicates a fault. Green LED indicates the system is ready.

 

su ux · 00 VDd6 · R01

 

9 PCM LED Descriptions (continued) Faa 38 LEOS %hing %hing Set NOTE: The figure an SPAR 7200 os an exa

 

•poN-r 6E suod peuum.alul epoN

 

Drive Enclosure LEDs figure 40 Drive Enclosure PCM LEDs o o CAUTION: DO not proceed Without first correcting all fault indications (except for PCM batteries). NOTE: The batteries are fully charged during shipment. The batteries rnay loose charge and show a degraded status immediately When power is applied. This is a temporary condition. Proceed With the system initialization and software installation. Check the LEDs again When the installation is complete. The duster is not formed until the storage system software installation has been performed.

 

Identifying Service Processor LEDs The HP 3PAR SP (Proliant DL320e) LEDs are located at the front and rear Of the SP. Figure 41 Front LEDs o

 

4 LIID LED/ button button and powg Health NIC Flashing Blue Green Green Flashing Red Green System is being managed rernotely System is on Waiting for System is on power Still cord is not attached supplied has System is on and System f-•lth is System is degraded System is critical System is OH to activity NO network link

 

 

or Flashing Green Blue 4 NIC link NIC ShtuS UI D LED/button NOTE: May rbt be a to Off (for hot-plug HP CS supplies ONLY) NO link NO activity is managed Off z or more Of the 'OllOwing • Power i Power Supply has failed Power Supply is in mode Power Supply error

 

评论
添加红包

请填写红包祝福语或标题

红包个数最小为10个

红包金额最低5元

当前余额3.43前往充值 >
需支付:10.00
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明:

1.余额是钱包充值的虚拟货币,按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载,可以购买VIP、付费专栏及课程。

余额充值