如何安装和设置Kwikset SmartCode门锁-CSDN博客

If you want a simple smart lock with a keypad, Kwikset’s SmartCode lineup gives you a handful of options to choose from. Here’s how to install and set them up.

如果您想要带键盘的简单智能锁， Kwikset的SmartCode阵容为您提供了多种选择。这是安装和设置它们的方法。

We’re using the SmartCode 916 lock, specifically, which comes with a touch screen of sorts that hides the keys until you touch it. It can also connect to a smarthome hub via a Z-Wave or ZigBee connection. However, be aware that while Kwikset smart locks are compatible with the Wink hub, you’ll only be able to lock and unlock it from the Wink app and that’s it. Other hubs also let you do things like manage user codes, but if you want something that will work completely with Wink, check out the Schlage Connect.

具体来说，我们使用的是SmartCode 916锁，它带有各种触摸屏，可以将按键隐藏起来，直到您触摸为止。它还可以通过Z-Wave或ZigBee连接连接到智能家居集线器。但是，请注意，尽管Kwikset智能锁与Wink集线器兼容，但您只能从Wink应用程序中对其进行锁定和解锁，仅此而已。其他集线器还允许您执行诸如管理用户代码之类的操作，但是如果您希望某些功能可以与Wink完全兼容，请查看Schlage Connect 。

In any case, let’s get started. The installation process is nearly identical across the whole SmartCode lineup. So no matter which one you have, you’ll be able to follow along just fine.

无论如何，让我们开始吧。在整个SmartCode系列中，安装过程几乎相同。因此，无论您拥有哪一个，您都可以正常进行。

第一步：删除现有的固定螺栓 (Step One: Remove Your Existing Deadbolt)

First, you’ll need to remove the current deadbolt installed on your door. This usually just involves removing a couple of screws from the lock’s face plate on the inside of your home.

首先，您需要卸下门上安装的当前固定螺栓。通常，这只涉及从房屋内部的锁面板上卸下几颗螺钉。

After removing those screws, the entire deadbolt should come apart pretty easily. Just separate the outside and inside portions of the deadbolt to remove the whole thing from the door. You may have to slightly tap on it with a mallet to loosen it up if it doesn’t come off easily.

卸下这些螺钉后，整个固定螺栓应很容易分开。只需分开锁舌的内部和内部，即可从门上卸下整个物品。如果不容易脱落，则可能需要用槌轻敲一下以使其松开。

Next, you’ll need to remove the latch. However, if your existing deadbolt is from Kwikset, you can use the existing latch and keep it installed, as it’s identical to the one that the smart lock comes with. If you do need to remove the existing latch, just remove the two screws holding it in place and pull it straight out.

接下来，您需要卸下闩锁。但是，如果您现有的固定螺栓来自Kwikset，则可以使用现有的闩锁并保持安装状态，因为它与智能锁随附的闩锁相同。如果确实需要卸下现有的闩锁，只需卸下将其固定到位的两颗螺钉，然后将其笔直拉出即可。

You now have a clean slate to install your new smart lock. Let’s get to the good part!

现在，您可以轻松安装新的智能锁。让我们充分发挥作用吧！

第二步：安装SmartCode智能锁 (Step Two: Install the SmartCode Smart Lock)

To begin install the new door latch if you’re not using an existing one. Slide the latch into the door, making sure that the middle hole in the latch is centered within the hole in the door. If it’s not, remove the latch and rotate the mechanism 180 degrees (while holding onto the actual deadbolt) to change the position of the middle hole. Re-insert the latch, making sure the “UP” marking on the latch is facing up.

如果您不使用现有的门闩，请先开始安装新的门闩。将闩锁滑入门中，确保闩锁的中间Kong居中在门Kong内。如果不是，请卸下闩锁并旋转机械装置180度(同时按住实际的固定螺栓)以更改中间Kong的位置。重新插入闩锁，确保闩锁上的“ UP”标记朝上。

Secure the latch to the door using the two short screws included with the kit.

使用套件随附的两个短螺钉将闩锁固定到门上。

Starting on the inside of the door, place the lock by feeding the cable underneath the latch and inserting the turn rod through the middle latch hole. Make sure to line up the “D” shape of the rod in order to get it in.

从门的内部开始，通过将电缆插入闩锁下方并将转杆插入中间闩锁Kong中来放置锁。确保对齐杆的“ D”形以便将其插入。

On the outside, place the mounting plate over the hole and feed the cable through it. Secure it to the rest of the lock using the two long bolts included in the kit. This should now hold the lock in place on your door.

在外部，将安装板放在Kong上，并将电缆穿过其中。使用套件中随附的两个长螺栓将其固定到锁的其余部分。现在，这应该可以将门上的锁固定到位。

Next, separate the cover from the mechanism and remove the battery pack.

接下来，将盖子与机械装置分开，然后取出电池组。

Connect the cable from the keypad side of the lock to the mechanism and tuck any of the excess cable into the extra space inside.

将电缆从锁的键盘侧连接到机械装置，并将多余的电缆塞入内部的多余空间。

After that, install the mechanism onto the door, making sure to line it up with the turn rod so that it slides into the hole on the mechanism.

之后，将机械装置安装到门上，并确保将其与转杆对齐，以使其滑入机械装置的Kong中。

Secure the mechanism to the door using the two small Phillips screws included in the kit and using the lower screw terminals on the sides.

使用套件中随附的两颗小Phillips螺钉将机械装置固定在门上，并使用侧面的下部螺钉端子将其固定。

Next, insert four AA batteries into the battery pack and re-insert the battery pack into the mechanism.

接下来，将四节AA电池插入电池组，然后将电池组重新插入机械装置中。

The lock will beep and the status light will light up. From there, the lock should actuate a couple of times and then beep again. If you see a checkmark light up on the keypad, then the installation was successful. If not, there was a problem with the installation—something may not be lined up in relation to the turn rod, or the deadbolt is blocked or getting caught on something.

锁将发出哔哔声，并且状态指示灯将点亮。从那里开始，锁应启动几次，然后再次发出蜂鸣声。如果您看到键盘上的复选标记点亮，则表明安装成功。如果不是，则说明安装存在问题-可能没有与转杆对齐的东西，或者死螺栓被卡住或卡在某些物体上。

Once successful, install the cover on the mechanism using the two small hex screws and the included allen key.

成功后，使用两个小六角螺钉和随附的内六角扳手将盖板安装在机构上。

After installation, the lock is technically ready to go, but you need to add a user code if you want to unlock it using the keypad. You can do this by taking off the black interior cover piece and pressing the program button while the door is unlocked.

安装后，锁在技术上已准备就绪，但是如果要使用键盘解锁，则需要添加用户代码。您可以通过打开黑色的内部盖板并在门未锁定时按下程序按钮来执行此操作。

Next, tap the checkmark on the keypad and then enter in the user code that you want to use, which must be between 4 and 8 digits. When done, tap on the lock button on the keypad.

接下来，点击小键盘上的复选标记，然后输入要使用的用户密码，该密码必须介于4到8位之间。完成后，点击键盘上的锁定按钮。

To activate the screen at any time (thus illuminating the keys), you can either press on it with your palm, touch the lower-left area, or tap on the screen with three or more fingers.

要随时激活屏幕(从而点亮按键)，您可以用手掌按在屏幕上，触摸左下角的区域，或者用三个或更多个手指在屏幕上点击。

第三步：将其连接到您的Smarthome Hub (Step Three: Connect It to Your Smarthome Hub)

SmartCode locks can be used without a smarthome hub, but the whole point of a smart lock is that you can control and manage the lock remotely from your phone, which is why it’s ideal to connect it to a smarthome hub.

SmartCode锁可以在没有智能家居集线器的情况下使用，但是智能锁的全部要点是您可以从手机远程控制和管理锁，这就是为什么将其连接到智能家居集线器的理想选择。

How you do this is completely dependent on what type of hub you have, but the process should be mostly the same all around. In my case, I’m going to connect the lock to my Wink hub.

您如何执行此操作完全取决于您所拥有的集线器类型，但是整个过程应该大致相同。就我而言，我将把锁连接到Wink集线器。

You’ll first need to open up your smarthome hub’s app and navigate to where you add a device to the hub to put it in search/discovery mode.

首先，您需要打开smarthome集线器的应用程序，然后导航到将设备添加到集线器的位置，以使其处于搜索/发现模式。