诺帝菲尔主机联动编程符号意义

2.1.2.4.4Logic Equation Operators 逻辑等式运算符
2.1.2.4.4.1.Logic Functions 逻辑功能
Logic Functions 逻辑功能
The installer can enter the equations in any combination wanted as long as the format of the logic function is followed from the list below. Error checking will be performed after the user has entered the complete equation. Possible errors are too many or two few parentheses, too many or two few arguments inside the parentheses, unknown function and unknown device type.
只要逻辑功能格式遵循下面列表，就可以任何需要的组合输入等式。输入完整等式后，就可执行错误检验。可能的错误原因有过多或过少括号、括号内操作数过多或过少以及未知功能和未知设备类型。
The “AND” Operator “与”运算符
Requires that each argument be active.
每个操作数都为真，则结果为真。
Example: AND(Z2,Z5,Z9) 举例：AND（Z2,Z5,Z9）
All three arguments in the equation must be active for the logic zone to activate.
等式中的三个区域必须都动作，才可激活逻辑区域。
The “OR” Operator “或”运算符
Requires that any argument be active
只要任何一个操作数为真，结果为真。
Example: OR(Z2,Z5,Z9) 举例：OR（Z2,Z5,Z9）
If any one of the three arguments in the equation is active the logic zone will be activated.
等式中三个区域中的任意一个激活，则逻辑运算结果为真。
The “NOT” Operator “非”运算符
Inverts the state of the argument (activated to deactivated OR deactivated to activated).
操作数状态取反（激活到停止或停止到激活）
Example: NOT(Z2) 举例：NOT（Z2）
The logic zone will remain active until the argument activates.
逻辑区域一直为真，直到Z2区激活为止。
If the argument activates, the logic zone will deactivate.
如果Z2激活，逻辑区域将被释放。
The “ONLY1” Operator “ONLY1”运算符
Requires that only one argument be active.
如果操作数仅有一个为真，则结果为真。
Example: ONLY1(Z2,Z5,Z9) 举例：ONLY1（Z2,Z5,Z9）
If only one of the arguments is active the logic zone will be activated.
如果Z2、Z5和Z9中仅有一个激活，则结果为真。
The “ANYX” Operator “ANYX”运算符
Requires that the amount of arguments specified by the number preceding the arguments be active.
指定个数的操作数全为真时，运算结果为真。
Example: ANYX(2,Z2,Z5,Z9) 举例：ANYX(2,Z2,Z5,Z9)
If any two or more of the arguments are active, the output point will activate.
如果Z2、Z5和Z9中任意两个激活时，结果为真。
The amount, X, may be a value from 1 through 9.
X可以是1到9的值。
The “XZONE” Operator “XZONE”运算符
Requires that any combination of two or more input devices programmed to a zone be active.
作为操作数的区域中有两个或更多输入设备激活时，结果为真。
Example: XZONE(Z2) 举例：XZONE(Z2)
If any combination of two or more initiating devices mapped to this software zone comes into alarm, then outputs mapped to this zone will activate.
如果Z2中有两个或更多设备激活时，结果为真。
The “RANGE” Operator “RANGE”运算符
Each argument within the range must conform to the requirements of the governing function. The range limit is 20 consecutive arguments.
定义地址连续的设备的范围，该范围内最多20个连续地址。所定义的范围可作为操作数。
Example: AND(RANGE(Z1,Z20)) 举例：AND（RANGE（Z1,Z20））
Zone 1 through Zone 20 must all be active to activate the logic zone.
Z1至Z20范围内的二十个区必须全部激活，结果才为真。