EasyIP Ensp春考技能考试11日考题解析

EasyIP技能实践

拓扑图

要求

LSW1上的配置

<Huawei>un t m
Info: Current terminal monitor is off.
//关闭提示信息
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
//进入系统视图
[Huawei]sy LSW1
//命名为LSW1
[LSW1]vl b 100 200
//划分vlan100和200
Info: This operation may take a few seconds. Please wait for a moment...done.
[LSW1]int g0/0/2
//进入接口配置相关的配置，模式为access
[LSW1-GigabitEthernet0/0/2]p l a
[LSW1-GigabitEthernet0/0/2]p d v 100
[LSW1-GigabitEthernet0/0/2]int g0/0/6
[LSW1-GigabitEthernet0/0/6]p l a
[LSW1-GigabitEthernet0/0/6]p d v 200
[LSW1-GigabitEthernet0/0/6]int g0/0/1
//将与路由器连接的接口设置为Trunk，并且允许多个Vlan通过。
[LSW1-GigabitEthernet0/0/1]p l t
[LSW1-GigabitEthernet0/0/1]p t a v a

AR1上的配置

<Huawei>un t m
Info: Current terminal monitor is off.
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sy AR1
//配置单臂路由
[AR1]int g0/0/0.100
[AR1-GigabitEthernet0/0/0.100]ip a 192.168.111.1 26
//配置vlan100的网关地址
[AR1-GigabitEthernet0/0/0.100]dot1q ter vid 100
//封装802.1协议，并且绑定vlan100
[AR1-GigabitEthernet0/0/0.100]arp b	
[AR1-GigabitEthernet0/0/0.100]arp broadcast en
//开启ARP
[AR1-GigabitEthernet0/0/0.100]int g0/0/0.200
[AR1-GigabitEthernet0/0/0.200]ip a 192.168.111.65 26
[AR1-GigabitEthernet0/0/0.200]dot1q ter vid 200
[AR1-GigabitEthernet0/0/0.200]arp b	
[AR1-GigabitEthernet0/0/0.200]arp broadcast en
[AR1-GigabitEthernet0/0/0.200]int g0/0/1
[AR1-GigabitEthernet0/0/1]ip a 192.168.110.1 30
//配置路由器出口IP地址
[AR1-GigabitEthernet0/0/1]ospf
//配置OSPF实现全网互通
[AR1-ospf-1]area 0
[AR1-ospf-1-area-0.0.0.0]net 192.168.111.0 0.0.0.63
//格式 net 网络地址 反掩码
[AR1-ospf-1-area-0.0.0.0]net 192.168.111.64 0.0.0.63
[AR1-ospf-1-area-0.0.0.0]net 192.168.110.0 0.0.0.3

AR2配置

<Huawei>un t m
Info: Current terminal monitor is off.
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sy AR2
[AR2]int g0/0/1
[AR2-GigabitEthernet0/0/1]ip a 200.100.1.1 24
[AR2-GigabitEthernet0/0/1]ospf 
[AR2-ospf-1]area 0
[AR2-ospf-1-area-0.0.0.0]net 192.168.110.0 0.0.0.3
[AR2-ospf-1-area-0.0.0.0]net 200.100.1.0 0.0.0.255
[AR2-ospf-1-area-0.0.0.0]acl 2000
//配置EasyIP，允许192.168.111.0和64网段使用EasyIP
[AR2-acl-basic-2000]rule permit source 192.168.111.0 0.0.0.63
[AR2-acl-basic-2000]rule permit source 192.168.111.64 0.0.0.63
[AR2-acl-basic-2000]int g0/0/1
[AR2-GigabitEthernet0/0/1]nat outbound 2000
//将EasyIP应用到接口上
[AR2-GigabitEthernet0/0/1]int g0/0/0
[AR2-GigabitEthernet0/0/0]ip a 192.168.110.2 30
//配置IP地址，笔者就是因为忘了配置IP地址导致在做完OSPF后无法实现全网互通

我们可以通过抓包可以发现我们EasyIP已经实现了。