STM32 PWM底层驱动

//说明：利用TIMER1的CH1即PA8端口输出PWM驱动蜂鸣器。以下是代码(在STM32F103上应用的)

void fn_pwm_init(INT16U _pwmFreq)
{
//ToDo: Add your code Here:
 /* Timer1 Channel 1, PA8 IO初始化*/
 GPIO_PinRemapConfig(GPIO_PartialRemap_TIM1,ENABLE);
 GPIO_InitTypeDef GPIO_InitStructure;
 
 GPIO_InitStructure.GPIO_Pin =  GPIO_Pin_8;
 GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
 GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
 GPIO_Init(GPIOA, &GPIO_InitStructure);

 //RCC的TIM1及IO时钟开启
 RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM1, ENABLE);
 RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_AFIO,ENABLE);

 //以下为TIM1初始化
 TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure;    
 //重新将Timer设置为缺省值  
 TIM_DeInit(TIM1);  
 //采用内部时钟给TIM1提供时钟源  
 TIM_InternalClockConfig(TIM1);  
 //预分频系数为0即不进行预分频此时TIMER的频率为48MHz  
 TIM_TimeBaseStructure.TIM_Prescaler = 1-1;//1分频，即不分频  
 //设置时钟分割  
 TIM_TimeBaseStructure.TIM_ClockDivision = TIM_CKD_DIV1;  
 //设置计数器模式为向上计数模式  
 TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up;  
 //设置计数溢出大小48000000为系统时钟  
 TIM_TimeBaseStructure.TIM_Period = (48000000/_pwmFreq)- 1;  
 //将配置应用到TIM1中  
 TIM_TimeBaseInit(TIM1,&TIM_TimeBaseStructure);
 
 //pwm初始化
 TIM_OCInitTypeDef TimOCInitStructure;   //设置缺省值  
 TIM_OCStructInit(&TimOCInitStructure);   //PWM模式1输出  
 TimOCInitStructure.TIM_OCMode = TIM_OCMode_PWM1;   //设置占空比占空比=(CCRx/ARR)*100%或(TIM_Pulse/TIM_Period)*100%  
 TimOCInitStructure.TIM_Pulse = 50 * 4800 / 100;   //50为100分比，1-100
 TimOCInitStructure.TIM_OCPolarity = TIM_OCPolarity_High;   //使能输出状态  
 TimOCInitStructure.TIM_OutputState = TIM_OutputState_Enable;   //TIM1的CH1输出  
 TIM_OC1Init(TIM1, &TimOCInitStructure);   //设置TIM1的PWM输出为使能  
 TIM_CtrlPWMOutputs(TIM1,DISABLE);
}

void fn_pwm_Cmd(FunctionalState NewState)
{
//ToDo: Add your code Here:
 TIM_CtrlPWMOutputs(TIM1, NewState);
 TIM_Cmd(TIM1, NewState);
 
}