the processes initialization failure after update the KIS

      2007.1.1---2007.1.3 I have updated the KIS by offline and online with the replace website supplied by Kaspersky.

     Firstly, all the important processes like Adobe,XDICT,ITune and realplayer can't come up after the KIS update. It's so amazing that all the processes can start up before the update.

     I  search some solutions on the website by baidu. I found that some one have encountered the similiar problems. they gave the valide solution like below:

    put the Mouse on the "configuration"-->"trustful area"-->"trustful program"-->"add" --->choose

   1.don't control the openned file.

   2. don't control the activity of the process

   3.don't control access the register table.

  • 0
    点赞
  • 0
    收藏
    觉得还不错? 一键收藏
  • 0
    评论
The initialization of UART4 can vary depending on the microcontroller or development board being used. However, here is an example of how to initialize UART4 on a STM32F4 Discovery board using CubeMX and HAL libraries: 1. Open CubeMX and create a new project for your microcontroller or development board. 2. In the "Pinout & Configuration" tab, select "UART4" from the peripherals list. 3. Enable the "Asynchronous" mode and set the baud rate to the desired value. 4. Set the word length, stop bits, and parity according to your application's requirements. 5. Configure the GPIO pins for the UART4 peripheral by selecting the appropriate pins in the "Pinout" tab. 6. Generate the code by clicking on the "Generate" button. 7. Open the generated code and locate the "MX_UART4_Init" function. 8. In this function, you will find the initialization code for UART4. It will look something like this: ``` huart4.Instance = UART4; huart4.Init.BaudRate = 115200; huart4.Init.WordLength = UART_WORDLENGTH_8B; huart4.Init.StopBits = UART_STOPBITS_1; huart4.Init.Parity = UART_PARITY_NONE; huart4.Init.Mode = UART_MODE_TX_RX; huart4.Init.HwFlowCtl = UART_HWCONTROL_NONE; huart4.Init.OverSampling = UART_OVERSAMPLING_16; if (HAL_UART_Init(&huart4) != HAL_OK) { Error_Handler(); } ``` 9. This code initializes UART4 with a baud rate of 115200, 8 data bits, 1 stop bit, no parity, and both transmit and receive modes enabled. 10. You can now use the HAL functions to send and receive data over UART4. For example, to transmit a string over UART4, you can use the following code: ``` char* str = "Hello, World!"; HAL_UART_Transmit(&huart4, (uint8_t*)str, strlen(str), HAL_MAX_DELAY); ``` This will send the string "Hello, World!" over UART4.

“相关推荐”对你有帮助么?

  • 非常没帮助
  • 没帮助
  • 一般
  • 有帮助
  • 非常有帮助
提交
评论
添加红包

请填写红包祝福语或标题

红包个数最小为10个

红包金额最低5元

当前余额3.43前往充值 >
需支付:10.00
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明:

1.余额是钱包充值的虚拟货币,按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载,可以购买VIP、付费专栏及课程。

余额充值