成功在skyeye 上实现U-Boot 的Nand命令并从Nand中启动Linux

http://www.linuxfans.org/bbs/thread-182694-1-1.html

1. 下载u-boot-1.1.4.tar.bz2,并解压
2. 将arm-linux-2.95.3复制到/usr/local/arm/2.95.3/
3. 编辑u-boot跟目录的Makefile文件

include $(TOPDIR)/config.mk
CROSS_COMPILE=/usr/local/arm/2.95.3/bin/arm-linux-
ifndef CROSS_COMPILE


smdk2410_config : unconfig
@./mkconfig $(@:_config=) arm arm920t smdk2410 NULL s3c24x0

sky2410_config : unconfig
@./mkconfig $(@:_config=) arm arm920t sky2410 NULL s3c24x0

SX1_config : unconfig
@./mkconfig $(@:_config=) arm arm925t sx1


4. 复制必要的文件
cp -arf board/smdk2410/ board/sky2410
mv board/sky2410/smdk2410.c board/sky2410/sky2410.c
cp include/configs/smdk2410.h include/configs/sky2410.h


5. 修改board/smdk2410/Makefile
LIB = lib$(BOARD).a

OBJS := sky2410.o flash.o
SOBJS := lowlevel_init.o



6. make 测试一下
make sky2410_config
make
出现错误
cc1: Invalid option `abi=apcs-gnu'
修改文件cpu/arm920t/config.mk
PLATFORM_CPPFLAGS +=$(call cc-option,-mapcs-32,-mabi=apcs-gnu)
改成：
PLATFORM_CPPFLAGS +=$(call cc-option,-mapcs-32,$(call cc-option,-mabi=apcs-gnu),)
再make成功

7. 开始移植nand
修改cpu/arm920t/start.S

将从Flash启动改成从NAND Flash启动。
将以下U－Boot的重定向语句段：

#ifndef CONFIG_SKIP_RELOCATE_UBOOT
relocate: /* relocate U-Boot to RAM */
adr r0, _start /* r0 <- current position of code */
ldr r1, _TEXT_BASE /* test if we run from flash or RAM */
cmp r0, r1 /* don't reloc during debug */
beq stack_setup

ldr r2, _armboot_start
ldr r3, _bss_start
sub r2, r3, r2 /* r2 <- size of armboot */
add r2, r0, r2 /* r2 <- source end address */

copy_loop:
ldmia r0!, {r3-r10} /* copy from source address [r0] */
stmia r1!, {r3-r10} /* copy to target address [r1] */
cmp r0, r2 /* until source end addreee [r2] */
ble copy_loop
#endif /* CONFIG_SKIP_RELOCATE_UBOOT */



替换成：

#ifdef CONFIG_S3C2410_NAND_BOOT
@ reset NAND
mov r1, #NAND_CTL_BASE
ldr r2, =0xf830 @ initial value
str r2, [r1, #oNFCONF]
ldr r2, [r1, #oNFCONF]
bic r2, r2, #0x800 @ enable chip
str r2, [r1, #oNFCONF]
mov r2, #0xff @ RESET command
strb r2, [r1, #oNFCMD]


mov r3, #0 @ wait
nand1:
add r3, r3, #0x1
cmp r3, #0xa
blt nand1

nand2:
ldr r2, [r1, #oNFSTAT] @ wait ready
tst r2, #0x1
beq nand2

ldr r2, [r1, #oNFCONF]
orr r2, r2, #0x800 @ disable chip
str r2, [r1, #oNFCONF]

@ get read to call C functions (for nand_read())
ldr sp, DW_STACK_START @ setup stack pointer
mov fp, #0 @ no previous frame, so fp=0

@ copy U-Boot to RAM
ldr r0, =TEXT_BASE
mov r1, #0x0
mov r2, #0x20000
bl nand_read_ll
tst r0, #0x0
beq ok_nand_read

bad_nand_read:
loop2: b loop2 @ infinite loop


ok_nand_read:
@ verify
mov r0, #0
ldr r1, =TEXT_BASE
mov r2, #0x400 @ 4 bytes * 1024 = 4K-bytes
go_next:
ldr r3, [r0], #4
ldr r4, [r1], #4
teq r3, r4
bne notmatch
subs r2, r2, #4
beq stack_setup
bne go_next

notmatch:
loop3: b loop3 @ infinite loop

#endif /* CONFIG_S3C2410_NAND_BOOT */

在 “ _start_armboot: .word start_armboot ” 后加入：
.align 2
DW_STACK_START: .word STACK_BASE+STACK_SIZE-4


8.
(I)修改board/smdk2410/Makefile
OBJS := sky2410.o flash.o

(II)修改board/sky2410/lowlevel_init.S
#define UBLB (0x1<<3)

#define B1_BWSCON (DW16)
#define B2_BWSCON (DW16)
#define B3_BWSCON (DW16 + WAIT + UBLB)
#define B4_BWSCON (DW16)

(III)创建board/smdk2410/nand_read.c文件
#include <config.h>
#define __REGb(x) (*(volatile unsigned char *)(x))
#define __REGi(x) (*(volatile unsigned int *)(x))
#define NF_BASE 0x4e000000
#define NFCONF __REGi(NF_BASE + 0x0)
#define NFCMD __REGb(NF_BASE + 0x4)
#define NFADDR __REGb(NF_BASE + 0x8)
#define NFDATA __REGb(NF_BASE + 0xc)
#define NFSTAT __REGb(NF_BASE + 0x10)
#define BUSY 1
inline void wait_idle(void) {
int i;
while(!(NFSTAT & BUSY))
for(i=0; i<10; i++);
}
/* low level nand read function */
int
nand_read_ll(unsigned char *buf, unsigned long start_addr, int size)
{
int i, j;
if ((start_addr & NAND_BLOCK_MASK) || (size & NAND_BLOCK_MASK)) {
return -1; /* invalid alignment */
}
/* chip Enable */
NFCONF &= ~0x800;
for(i=0; i<10; i++);
for(i=start_addr; i < (start_addr + size);) {
/* READ0 */
NFCMD = 0;
/* Write Address */
NFADDR = i & 0xff;
NFADDR = (i >> 9) & 0xff;
NFADDR = (i >> 17) & 0xff;
NFADDR = (i >> 25) & 0xff;
wait_idle();
for(j=0; j < NAND_SECTOR_SIZE; j++, i++) {
*buf = (NFDATA & 0xff);
buf++;
}
}
/* chip Disable */
NFCONF |= 0x800; /* chip disable */
return 0;
}

9.修改include/configs/sky2410.h
在文件的后部添加
/*
* Nandflash Boot
*/
#define CONFIG_S3C2410_NAND_BOOT 1
#define STACK_BASE 0x33f00000
#define STACK_SIZE 0x8000
//#define UBOOT_RAM_BASE 0x33f80000
/* NAND Flash Controller */
#define NAND_CTL_BASE 0x4E000000
#define bINT_CTL(Nb) __REG(INT_CTL_BASE + (Nb))
/* Offset */
#define oNFCONF 0x00
#define oNFCMD 0x04
#define oNFADDR 0x08
#define oNFDATA 0x0c
#define oNFSTAT 0x10
#define oNFECC 0x14

10.
make 测试一下啊
到这里 u-boot 已经可以从nand启动了
下面我们对u-boot添加nand指令的支持

11. 修改include/configs/sky2410.h
(I)去掉CFG_CMD_NAND的注释
#define CONFIG_COMMANDS /
(CONFIG_CMD_DFL | /
CFG_CMD_CACHE | /
CFG_CMD_NAND | /
/*CFG_CMD_EEPROM |*/ /
/*CFG_CMD_I2C |*/ /
/*CFG_CMD_USB |*/ /
CFG_CMD_REGINFO | /
CFG_CMD_DATE | /
CFG_CMD_ELF)

(II) 修改我们在第9步修改的内容
#define CFG_NAND_LEGACY
#define CFG_ENV_OFFSET 0X20000
#if (CONFIG_COMMANDS & CFG_CMD_NAND)
#define CFG_NAND_BASE 0x4E000000
/* NandFlash控制器在SFR区起始寄存器地址 */
#define CFG_MAX_NAND_DEVICE 1
/* 支持的最在Nand Flash数据 */
#define SECTORSIZE 512
/* 1页的大小 */
#define NAND_SECTOR_SIZE SECTORSIZE
#define NAND_BLOCK_MASK 511
/* 页掩码 */
#define ADDR_COLUMN 1
/* 一个字节的Column地址 */
#define ADDR_PAGE 3
/* 3字节的页块地址!!!!!*/
#define ADDR_COLUMN_PAGE 4
/* 总共4字节的页块地址!!!!! */
#define NAND_ChipID_UNKNOWN 0x00
/* 未知芯片的ID号 */
#define NAND_MAX_FLOORS 1
#define NAND_MAX_CHIPS 1
/* Nand Flash命令层底层接口函数 */
#define WRITE_NAND_COMMAND(d, adr) {rNFCMD = d;}
#define WRITE_NAND_ADDRESS(d, adr) {rNFADDR = d;}
#define WRITE_NAND(d, adr) {rNFDATA = d;}
#define READ_NAND(adr) (rNFDATA)
#define NAND_WAIT_READY(nand) {while(!(rNFSTAT&(1<<0)));}
#define NAND_DISABLE_CE(nand) {rNFCONF |= (1<<11);}
#define NAND_ENABLE_CE(nand) {rNFCONF &= ~(1<<11);}
/* the following functions are NOP's because S3C24X0 handles this in hardware 一定要加上 */
#define NAND_CTL_CLRALE(nandptr)
#define NAND_CTL_SETALE(nandptr)
#define NAND_CTL_CLRCLE(nandptr)
#define NAND_CTL_SETCLE(nandptr)
/* 允许Nand Flash写校验 */
#define CONFIG_MTD_NAND_VERIFY_WRITE 1
/*
* Nandflash Boot
*/
#define CONFIG_S3C2410_NAND_BOOT 1
#define STACK_BASE 0x33f00000
#define STACK_SIZE 0x8000
//#define UBOOT_RAM_BASE 0x33f80000
/* NAND Flash Controller */
#define NAND_CTL_BASE 0x4E000000
#define bINT_CTL(Nb) __REG(INT_CTL_BASE + (Nb))
/* Offset */
#define oNFCONF 0x00
#define oNFCMD 0x04
#define oNFADDR 0x08
#define oNFDATA 0x0c
#define oNFSTAT 0x10
#define oNFECC 0x14
#define rNFCONF (*(volatile unsigned int *)0x4e000000)
#define rNFCMD (*(volatile unsigned char *)0x4e000004)
#define rNFADDR (*(volatile unsigned char *)0x4e000008)
#define rNFDATA (*(volatile unsigned char *)0x4e00000c)
#define rNFSTAT (*(volatile unsigned int *)0x4e000010)
#define rNFECC (*(volatile unsigned int *)0x4e000014)
#define rNFECC0 (*(volatile unsigned char *)0x4e000014)
#define rNFECC1 (*(volatile unsigned char *)0x4e000015)
#define rNFECC2 (*(volatile unsigned char *)0x4e000016)
#endif /* CONFIG_COMMANDS & CFG_CMD_NAND*/

12. 修改 board/sky2410/sky2410.c
在文件尾部添加
#if (CONFIG_COMMANDS & CFG_CMD_NAND)
typedef enum {
NFCE_LOW,
NFCE_HIGH
} NFCE_STATE;

static inline void NF_Conf(u16 conf)
{
S3C2410_NAND * const nand = S3C2410_GetBase_NAND();

nand->NFCONF = conf;
}

static inline void NF_Cmd(u8 cmd)
{
S3C2410_NAND * const nand = S3C2410_GetBase_NAND();

nand->NFCMD = cmd;
}

static inline void NF_CmdW(u8 cmd)
{
NF_Cmd(cmd);
udelay(1);
}

static inline void NF_Addr(u8 addr)
{
S3C2410_NAND * const nand = S3C2410_GetBase_NAND();

nand->NFADDR = addr;
}

static inline void NF_SetCE(NFCE_STATE s)
{
S3C2410_NAND * const nand = S3C2410_GetBase_NAND();

switch (s) {
case NFCE_LOW:
nand->NFCONF &= ~(1<<11);
break;

case NFCE_HIGH:
nand->NFCONF |= (1<<11);
break;
}
}

static inline void NF_WaitRB(void)
{
S3C2410_NAND * const nand = S3C2410_GetBase_NAND();

while (!(nand->NFSTAT & (1<<0)));
}

static inline void NF_Write(u8 data)
{
S3C2410_NAND * const nand = S3C2410_GetBase_NAND();

nand->NFDATA = data;
}

static inline u8 NF_Read(void)
{
S3C2410_NAND * const nand = S3C2410_GetBase_NAND();

return(nand->NFDATA);
}

static inline void NF_Init_ECC(void)
{
S3C2410_NAND * const nand = S3C2410_GetBase_NAND();

nand->NFCONF |= (1<<12);
}

static inline u32 NF_Read_ECC(void)
{
S3C2410_NAND * const nand = S3C2410_GetBase_NAND();

return(nand->NFECC);
}

#endif
/*

* NAND flash initialization.
*/
#if (CONFIG_COMMANDS & CFG_CMD_NAND)
extern ulong nand_probe(ulong physadr);


static inline void NF_Reset(void)
{
int i;

NF_SetCE(NFCE_LOW);
NF_Cmd(0xFF); /* reset command */
for(i = 0; i < 10; i++); /* tWB = 100ns. */
NF_WaitRB(); /* wait 200~500us; */
NF_SetCE(NFCE_HIGH);
}


static inline void NF_Init(void)
{
#if 0 /* a little bit too optimistic */
#define TACLS 0
#define TWRPH0 3
#define TWRPH1 0
#else
#define TACLS 0
#define TWRPH0 4
#define TWRPH1 2
#endif

NF_Conf((1<<15)|(0<<14)|(0<<13)|(1<<12)|(1<<11)|(TACLS<<8)|(TWRPH0<<4)|(TWRPH1<<0));
/*nand->NFCONF = (1<<15)|(1<<14)|(1<<13)|(1<<12)|(1<<11)|(TACLS<<8)|(TWRPH0<<4)|(TWRPH1<<0); */
/* 1 1 1 1, 1 xxx, r xxx, r xxx */
/* En 512B 4step ECCR nFCE=H tACLS tWRPH0 tWRPH1 */

NF_Reset();
}

void
nand_init(void)
{
S3C2410_NAND * const nand = S3C2410_GetBase_NAND();

NF_Init();
#ifdef DEBUG
printf("NAND flash probing at 0x%.8lX/n", (ulong)nand);
#endif
printf ("%4lu MB/n", nand_probe((ulong)nand) >> 20);
}
#endif

现在我问对uboot的nand指令的修改也完成了

上面的步骤基本的在网上也能找到
但是,如果就真么直接使用的话 skyeye1.2.4就会报错

SMDK2410 # nand read 33000000 0 20000
NAND read: device 0 offset 0, size 131072 ... warning when RE falling,do nothing
0 bytes read: ERROR

最后花费一天的时间跟踪 skyeye 和u-boot 终于找到错误的原因了

在u-boot读取oob数据时
NanD_Command(nand, NAND_CMD_READOOB)
然后
NanD_Address(nand, ADDR_COLUMN_PAGE
这个时候 skyeye模拟的nand就准备好数据了
其实直接就可以 READ_NAND (nandptr)了

但是在u-boot的NanD_ReadBuf函数中又发送了一次NanD_Command (nand, NAND_CMD_READ0);
结果skyeye就认为命令发生了改变 然后就开始等待NanD_Address(nand, ADDR_COLUMN_PAGE了
可是u-boot在发送NanD_Command (nand, NAND_CMD_READ0);后就直接开始读取
skyeye 就认为是没有发送地址然后就报错了

最简单的办法就是吧NanD_ReadBuf中的NanD_Command (nand, NAND_CMD_READ0);这一行注释掉

就没有问题了~~
而且我也测试过将修改后的u-boot下载的我的开发板中 经过检测没有任何问题的