Door Man
Time Limit: 1000MS | Memory Limit: 10000K | |
Description
You are a butler in a large mansion. This mansion has so many rooms that they are merely referred to by number (room 0, 1, 2, 3, etc...). Your master is a particularly absent-minded lout and continually leaves doors open throughout a particular floor of the house. Over the years, you have mastered the art of traveling in a single path through the sloppy rooms and closing the doors behind you. Your biggest problem is determining whether it is possible to find a path through the sloppy rooms where you:
In this problem, you are given a list of rooms and open doors between them (along with a starting room). It is not needed to determine a route, only if one is possible.
- Always shut open doors behind you immediately after passing through
- Never open a closed door
- End up in your chambers (room 0) with all doors closed
In this problem, you are given a list of rooms and open doors between them (along with a starting room). It is not needed to determine a route, only if one is possible.
Input
Input to this problem will consist of a (non-empty) series of up to 100 data sets. Each data set will be formatted according to the following description, and there will be no blank lines separating data sets.
A single data set has 3 components:
Following the final data set will be a single line, "ENDOFINPUT".
Note that there will be no more than 100 doors in any single data set.
A single data set has 3 components:
- Start line - A single line, "START M N", where M indicates the butler's starting room, and N indicates the number of rooms in the house (1 <= N <= 20).
- Room list - A series of N lines. Each line lists, for a single room, every open door that leads to a room of higher number. For example, if room 3 had open doors to rooms 1, 5, and 7, the line for room 3 would read "5 7". The first line in the list represents room 0. The second line represents room 1, and so on until the last line, which represents room (N - 1). It is possible for lines to be empty (in particular, the last line will always be empty since it is the highest numbered room). On each line, the adjacent rooms are always listed in ascending order. It is possible for rooms to be connected by multiple doors!
- End line - A single line, "END"
Following the final data set will be a single line, "ENDOFINPUT".
Note that there will be no more than 100 doors in any single data set.
Output
For each data set, there will be exactly one line of output. If it is possible for the butler (by following the rules in the introduction) to walk into his chambers and close the final open door behind him, print a line "YES X", where X is the number of doors he closed. Otherwise, print "NO".
Sample Input
START 1 2 1 END START 0 5 1 2 2 3 3 4 4 END START 0 10 1 9 2 3 4 5 6 7 8 9 END ENDOFINPUT
Sample Output
YES 1 NO YES 10
————————————————————顺劈的分割线————————————————————
思路:是否存在欧拉回路。保证图是连通的,就不必使用并查集判断连通了。终点必然是0,起点是0的话,就不能存在奇数点。起点不是0,那么起点和0都必须是奇数点。
主要是考查输入输出。。。。。。用gets读入,然后模拟一下。
代码如下:
/*
ID: j.sure.1
PROG:
LANG: C++
*/
/****************************************/
#include <cstdio>
#include <cstdlib>
#include <cstring>
#include <algorithm>
#include <cmath>
#include <stack>
#include <queue>
#include <vector>
#include <map>
#include <string>
#include <climits>
#include <iostream>
#define INF 0x3f3f3f3f
using namespace std;
/****************************************/
const int N = 25;
int st, n;
int tot, cnt[N];
int main()
{
#ifdef J_Sure
freopen("000.in", "r", stdin);
freopen("999.out", "w", stdout);
#endif
char op[10];
while(scanf("%s", op)) {
if(!strcmp(op, "ENDOFINPUT")) break;
tot = 0;
memset(cnt, 0, sizeof(cnt));
scanf("%d%d", &st, &n); getchar();
char s[1000];
for(int i = 0; i < n; i++) {
gets(s);
int len = strlen(s);
for(int k = 0; k < len; k++) {
int t = 0;
while(s[k] >= '0' && s[k] <= '9') {
t *= 10;
t += (s[k] - '0');
k++;
}
cnt[i]++; cnt[t]++;
tot++;
}
}
bool flag = true;
for(int i = 1; i < n; i++) if(i != st) {
if(cnt[i] & 1) {
flag = false;
break;
}
}
if(st == 0) {
if(cnt[0] & 1) flag = false;
}
else {
if(!(cnt[0]&1) || !(cnt[st]&1))
flag = false;
}
if(flag) printf("YES %d\n", tot);
else puts("NO");
scanf("%s", op);
}
return 0;
}