基于51单片机的智能家居家电设备控制系统proteus仿真原理图PCB

功能介绍：
0.本系统采用STC89C52作为单片机
1.系统实时显示当前的日期/时间，循环显示当前的温度/继电器控制状态
2.按键可设定温度，可控制继电器开关，系统设置了三路继电器，可以分别控制三种不同的家用设备
3.温度传感器采用的型号是常见的DS18B20，该传感器精度和测温范围都良好
4.采用DC002作为电源接口可直接输入5V给整个系统供电

原理图：

PCB ：

主程序：

#include "main.h"

/*******************变量定义*********************/
enum _MODE_DF_ dispMode;
bit modeFlag = AUTO; //模式标记
uchar setIndex = 0;

bit dispFlag = 0;

float temperature;

bit relay1Flag = 0;
bit relay2Flag = 0;
bit relay3Flag = 0;

char dis[16];

/********************************************************
函数名称:void mian()
函数作用:主函数
参数说明:
********************************************************/
void main()
{
    modeFlag = MANUAL;

    Timer0_Init(); //初始化定时器0
    DS1302_Init(); //初始化DS1302

    LCD_Init();   //初始化液晶
    DelayMs(200); //延时有助于稳定
    LCD_DispStr(4, 0, "Welcome!");
	DelayS(1);
    LCD_Clear();  //清屏


    while (1) //死循环
    {
        if (dispFlag == 1)
        {
            dispFlag = 0;
            Relay_Ctrl();
            if (dispMode == NORMAL)
            {
                DispNormal();
            }
        }

        KeyProcess();
    }   
}

/*------------------------------------------------
                    定时器初始化子程序
------------------------------------------------*/
void Timer0_Init(void)
{
    TMOD |= 0x01; //使用模式1，16位定时器，使用"|"符号可以在使用多个定时器时不受影响
    TH0 = (65536 - 9216) / 256; //重新赋值 10ms
    TL0 = (65536 - 9216) % 256;
    EA = 1;  //总中断打开
    ET0 = 1; //定时器中断打开
    TR0 = 1; //定时器开关打开
}
/*------------------------------------------------
                定时器中断子程序
------------------------------------------------*/
void Timer0_Interrupt(void) interrupt 1
{
    static unsigned int time10ms  = 0;
    TH0 = (65536 - 9216) / 256; //重新赋值 10ms
    TL0 = (65536 - 9216) % 256;
    time10ms++;

    if (time10ms > 50)
    {
        time10ms = 0;
        dispFlag = 1; //显示标志
    }
}

void DispNormal(void)
{
    static int tempBuf = 0;
    static unsigned char cnt = 0;
    
    DS1302_ReadTime();

    switch (timeBufDec[7])
    {
        case 1: sprintf(dis, "%02d/%02d/%02d   Sun. ", (int)timeBufDec[1], (int)timeBufDec[2], (int)timeBufDec[3]); break;
        case 2: sprintf(dis, "%02d/%02d/%02d   Mon. ", (int)timeBufDec[1], (int)timeBufDec[2], (int)timeBufDec[3]); break;
        case 3: sprintf(dis, "%02d/%02d/%02d   Tue. ", (int)timeBufDec[1], (int)timeBufDec[2], (int)timeBufDec[3]); break;
        case 4: sprintf(dis, "%02d/%02d/%02d   Wed. ", (int)timeBufDec[1], (int)timeBufDec[2], (int)timeBufDec[3]); break;
        case 5: sprintf(dis, "%02d/%02d/%02d  Thur. ", (int)timeBufDec[1], (int)timeBufDec[2], (int)timeBufDec[3]); break;
        case 6: sprintf(dis, "%02d/%02d/%02d   Fri. ", (int)timeBufDec[1], (int)timeBufDec[2], (int)timeBufDec[3]); break;
        case 7: sprintf(dis, "%02d/%02d/%02d   Sat. ", (int)timeBufDec[1], (int)timeBufDec[2], (int)timeBufDec[3]); break;
        default: sprintf(dis, "%02d/%02d/%02d   Sun. ", (int)timeBufDec[1], (int)timeBufDec[2], (int)timeBufDec[3]); break;
    }
    LCD_DispStr(0, 0, dis);

    while(!DS18B20_Start());
    DS18B20_GetTemp(&tempBuf);
    temperature = (float)tempBuf * 0.0625;

    sprintf(dis, "%02d:%02d:%02d ", (int)timeBufDec[4], (int)timeBufDec[5], (int)timeBufDec[6]);
    LCD_DispStr(0, 1, dis);

    cnt++;
    if (cnt < 5) //定时显示温度
    {
        sprintf(dis, "%5.1f", temperature);
        LCD_DispStr(9, 1, dis);
        LCD_DispOneChar(14, 1, 0xdf); //℃
        LCD_DispOneChar(15, 1, 'C');
    }
    else if (cnt < 10) //定时显示继电器状态
    {
        if (relay1Flag == 1)
        {
            LCD_DispStr(9, 1, " 1o");
        }
        else
        {
            LCD_DispStr(9, 1, " 1c");
        }
        
        if (relay2Flag == 1)
        {
            LCD_DispStr(12, 1, "2o");
        }
        else
        {
            LCD_DispStr(12, 1, "2c");
        }
        
        if (relay3Flag == 1)
        {
            LCD_DispStr(14, 1, "3o");
        }
        else
        {
            LCD_DispStr(14, 1, "3c");
        }
    }
    else
    {
        cnt = 0;
    }

}

void Relay_Ctrl(void)
{
    if (relay1Flag == 1)
    {
        RELAY_1 = ON;
    }
    else
    {
        RELAY_1 = OFF;
    }
    
    if (relay2Flag == 1)
    {
        RELAY_2 = ON;
    }
    else
    {
        RELAY_2 = OFF;
    }
    
    if (relay3Flag == 1)
    {
        RELAY_3 = ON;
    }
    else
    {
        RELAY_3 = OFF;
    } 
}

void DispSetRealTime(unsigned char setIndex)
{
    sprintf(dis, "%02d/%02d/%02d", (int)timeBufDec[1], (int)timeBufDec[2], (int)timeBufDec[3]);
    LCD_DispStr(0, 0, dis);
    switch (timeBufDec[7])
    {
        case 1: LCD_DispStr(10, 0, " Sun."); break;
        case 2: LCD_DispStr(10, 0, " Mon."); break;
        case 3: LCD_DispStr(10, 0, " Tue."); break;
        case 4: LCD_DispStr(10, 0, " Wed."); break;
        case 5: LCD_DispStr(10, 0, "Thur."); break;
        case 6: LCD_DispStr(10, 0, " Fri."); break;
        case 7: LCD_DispStr(10, 0, " Sat."); break;
        default: LCD_DispStr(10, 0, " Sun."); break;
    }
    sprintf(dis, "    %02d:%02d:%02d   ", (int)timeBufDec[4], (int)timeBufDec[5], (int)timeBufDec[6]);
    LCD_DispStr(0, 1, dis);

    switch (setIndex)
    {
        case 1: LCD_SetCursor(1, 0, 1); break;
        case 2: LCD_SetCursor(4, 0, 1); break;
        case 3: LCD_SetCursor(7, 0, 1); break;
        case 4: LCD_SetCursor(14, 0, 1); break;
        case 5: LCD_SetCursor(5, 1, 1); break;
        case 6: LCD_SetCursor(8, 1, 1); break;
        case 7: LCD_SetCursor(11, 1, 1); break;
        default:break;
    }
}

仿真演示视频：
https://www.bilibili.com/video/BV1D5411X7jE/

实物演示视频：
https://www.bilibili.com/video/BV1y841147bY/