Android - Audio - Qcom平台 - hac器件bring up

 

• 背景
• 正文
  • 助听器构造
  • 使用方式
  • HAC部分硬件原理图
  • 硬件调试需求
  • 软件平台及框架
    • a:mixer_path.xml中添加hac path
    • b:alsa用户空间，tinyalsa中注册HAC控件
    • c:GPIO_HAC_EN
    • d:添加acdb_id
    • e:为MMITest添加测试项
• 结语

背景

公司的项目要求支持助听器（HAC器件，Hearing Aid Compatibility），以此正好再复习一下在android的框架下如何bring up一个类似PA的器件。

正文

1. 我们首先需要了解助听器的原理，使用方式（以此确定测试手段），硬件原理图（以此确定软件如何适配），硬件调试需求，软件平台以及框架（MTK和Qcom在底层有一些差别）。

2. 既然已经明确了步骤，那么就开始一步一步来；

   (1)助听器构造:

   从百度百科来看，助听器有5个主要的构造，麦克风，放大器，接收器，电源和外壳。
   其中对我们这次开发有用的就是接收器，因为mic用手机的mic就够了。

   (2)使用方式:

   按照我拿到的助听器，上了电池之后默认是放大声音的模式，我理解的助听器基本上也是放大器的作用，但是HAC器件实际上还有一个功能，就是电圈耦合，按下助听器上的按钮触发，从以往的功能定义来看在打电话的时候该功能才打开（但是个人疑问助听器不是应该时时刻刻都帮助听障人士更清楚的听到声音么，难道是怕耗电快？）。
   知道了使用方式，我在测试效果的时候发现Receiver发出的声音实际上会影响到功能判断，所以我直接将Receiver器件和speaker器件给去掉了（去掉speaker主要是为了测试后面添加path的可行性。）

   (3)HAC部分硬件原理图:

+-----------+ INP +-------------+ VON +----------+ | CDC_EAR_M | ~~~~~> | | ~~~~~> | HAC 线圈 | +-----------+ | | +----------+ | | VOP ^ | AW8155FCR | ~~~~~~~~~* | | +-----------+ INN | | | CDC_EAR_P | ~~~~~> | | +-----------+ +-------------+ ^ } INP } +-------------+ | GPIO_HAC_EN | +-------------+

从原理图我们能明显的看到有一个艾薇的放大器，通过对CDC_EAR通路的查询，发现接到了Receiver器件上，所以电信号的数据输出可以理解为既给了Receiver，会给到hac部分。

(4)硬件调试需求:

和硬件同事进行沟通，发现有如下需求
–1. 器件bring up。
–2. 单独一条acdb id。
–3. dialer界面有设置HAC功能打开的接口。
–4. MMITest里面能进行测试。

(5)软件平台及框架:

根据需求，我们可以大致确定这需要从上到下一起打通，那么就需要像普通的PA那样单独配置一个path，而且还需要额外加一条acdb_id，以供调试。

然后就是和上层通信的接口，可以按照属性值的方式来，也可以按照其他方式，暂时先通过属性值来比较方便。

MMITest当中则需要通过path的开关来控制，所以配置一个单独的path是必须的。

根据以上的软件需求，我将此次的软件开发分为如下步骤：
a : mixer_path.xml中添加hac path。
b : 在alsa用户空间，tinyalsa中注册HAC控件。
c : tinyalsa中操作mixer，达到想调用hac path的时候能操作GPIO_HAC_EN，数据信号则不在此处控制。
d : hal层添加一个RX 的 acdb_id，TX已经确定是4，RX为31。
e : MMITest测试调用的audio_test.sh中添加 HAC PATH 的开关。

a

在hardware/qcom/audio/configs/msm8937/mixer_path_mtp.xml中添加HAC_PA的控件声明和path操作。

<ctl name="EAR PA Boost" value="ENABLE" /> <!-- begin mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 --> <ctl name="HAC_PA" value="On" /> <ctl name="HAC_PA" value="Off" /> <!-- end mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 --> <ctl name="MI2S_RX Channels" value="One" />

在需要打开PA的场景中打开PA，此处应个人测试需求，在speaker的path中也打开了HAC_PA。

<path name="voice-call"> <ctl name="PRI_MI2S_RX_Voice Mixer CSVoice" value="1" /> <ctl name="Voice_Tx Mixer TERT_MI2S_TX_Voice" value="1" /> <!-- begin mod by fuhua for task: 8668750 on 2019-12-03 task id:8668750 --> <ctl name="HAC_PA" value="On" /> <!-- end mod by fuhua for task: 8668750 on 2019-12-03 task id:8668750 --> </path> <path name="speaker"> <ctl name="RX3 MIX1 INP1" value="RX1" /> <ctl name="SPK" value="Switch" /> <!-- begin mod by fuhua for task: 8668750 on 2019-12-03 task id:8668750 --> <ctl name="HAC_PA" value="On" /> <!-- end mod by fuhua for task: 8668750 on 2019-12-03 task id:8668750 --> </path>

这个时候我们能在mixer.xml中看到配置了path，但是tinyalsa并没有注册HAC_PA这条path，在我的理解这个并不是针对注册的接口。
至于为什么选择的是 mixer_paths_mtp.xml ，这个可以查看/hardware/qcom/audio/hal/msm8916/platform.c对声卡的判断，然后选择对应的mixer_path.xml文件。

b

在alsa用户空间，tinyalsa中注册HAC控件。

注册的时候需要用到alsa提供出来的接口SOC_ENUM_SINGLE_EXT，当然也有其他的接口，比如SOC_DAPM_ENUM、SOC_SINGLE_TLV；这两个分别是需要注册到动态音频电源管理模块，另外一个的注释是“Convenience kcontrol builders”，主要用于定义那些有增益控制的控件，例如音量控制器，EQ均衡器等等。
我的代码如下( 路径：vendor/qcom/opensource/audio-kernel/asoc/codecs/sdm660_cdc/msm-analog-cdc.c )：

/*begin mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ static const char * const hac_pa_text[] = { "Off", "On"}; static const struct soc_enum hac_enum[] = { SOC_ENUM_SINGLE_EXT(2, hac_pa_text), }; /*end mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ ... /*begin mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ SOC_ENUM_EXT("HAC_PA", hac_enum[0], hac_pa_gpio_get,hac_pa_gpio_set), /*end mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */

c

实际上这里已经注册好了HAC_PA了，只要申明一下set函数和get函数，然后编译就能用tinymix看到HAC_PA的path了，但显然是不能工作的。
所以接下来就是定义hac_pa_gpio_get以及hac_pa_gpio_set，其中hac_pa_set需要额外在sdm660_cdc_priv结构体中添加，

/*begin mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ static int hac_pa_gpio_get(struct snd_kcontrol *kcontrol, struct snd_ctl_elem_value *ucontrol) { struct snd_soc_codec *codec = snd_soc_kcontrol_codec(kcontrol); struct sdm660_cdc_priv *sdm660_cdc = snd_soc_codec_get_drvdata(codec); ucontrol->value.integer.value[0] = (sdm660_cdc->hac_pa_set ? 1 : 0); dev_err(codec->dev, "%s: fuhua sdm660_cdc->hac_pa_set = %d\n", __func__, sdm660_cdc->hac_pa_set); return 0; } static int hac_pa_gpio_set(struct snd_kcontrol *kcontrol, struct snd_ctl_elem_value *ucontrol) { struct snd_soc_codec *codec = snd_soc_kcontrol_codec(kcontrol); struct sdm660_cdc_priv *sdm660_cdc = snd_soc_codec_get_drvdata(codec); dev_err(codec->dev, "%s: fuhua ucontrol->value.integer.value[0] = %ld\n", __func__, ucontrol->value.integer.value[0]); sdm660_cdc->hac_pa_set = (ucontrol->value.integer.value[0] ? true : false); if(sdm660_cdc->hac_pa_set) { //msm_cdc_pinctrl_select_active_state(sdm660_cdc->hac_pa_gpio_p); //enable_hac_pa(codec,true); if (sdm660_cdc->codec_hac_pa_cb) sdm660_cdc->codec_hac_pa_cb(codec, 1); } else { //msm_cdc_pinctrl_select_sleep_state(sdm660_cdc->hac_pa_gpio_p); //enable_hac_pa(codec,false); if (sdm660_cdc->codec_hac_pa_cb) sdm660_cdc->codec_hac_pa_cb(codec, 0); } return 0; } /*end mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */

其中的set函数会读取HAC_PA的控件值，然后去调用sdm660_cdc->codec_hac_pa_cb函数，而这个函数指针在另一个地方已经赋值成了另一个函数，如下sdm660_cdc->codec_hac_pa_cb = codec_hac_pa;：

/*begin mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ void msm_anlg_cdc_hac_pa_cb( int (*codec_hac_pa)(struct snd_soc_codec *codec, int enable), struct snd_soc_codec *codec) { struct sdm660_cdc_priv *sdm660_cdc; if (!codec) { pr_err("%s: NULL codec pointer!\n", __func__); return; } sdm660_cdc = snd_soc_codec_get_drvdata(codec); dev_err(codec->dev, "%s: fuhua Enter\n", __func__); sdm660_cdc->codec_hac_pa_cb = codec_hac_pa; } EXPORT_SYMBOL(msm_anlg_cdc_hac_pa_cb); /*end mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */

这个msm_anlg_cdc_hac_pa_cb已经在msm-analog-cdc.h中已经声明成extern。刚刚我们在sdm660_cdc这个目录下完成了驱动的注册，现在来到vendor/qcom/opensource/audio-kernel/asoc/msm8952.c继续完成实现，这些都是在alsa的用户空间进行操作的，也就是用了接口之后的部分。我们首先要在msm_audrx_init函数中调用msm_anlg_cdc_hac_pa_cb(enable_hac_pa, ana_cdc);，以注册enable_hac_pa函数。

static int msm_audrx_init(struct snd_soc_pcm_runtime *rtd) { struct snd_soc_codec *dig_cdc = rtd->codec_dais[DIG_CDC]->codec; struct snd_soc_codec *ana_cdc = rtd->codec_dais[ANA_CDC]->codec; ... snd_soc_dapm_ignore_suspend(dapm, "EAR"); snd_soc_dapm_ignore_suspend(dapm, "HEADPHONE"); snd_soc_dapm_ignore_suspend(dapm, "SPK_OUT"); ... /*begin mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ msm_anlg_cdc_hac_pa_cb(enable_hac_pa, ana_cdc); /*end mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */

这个init函数中我们还能看到snd_soc_dapm_ignore_suspend函数，这就是在哪里忽略path的地方。那么接下来就是具体实现enable_hac_pa ,代码如下：

/*begin mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ static int enable_hac_pa(struct snd_soc_codec *codec, int enable) { struct snd_soc_card *card = codec->component.card; struct msm_asoc_mach_data *pdata = snd_soc_card_get_drvdata(card); int ret = 0; int i = 0; int extamp_mode = 2; //ext pa default mode 2 if (!gpio_is_valid(pdata->hac_pa_gpio)) { pr_err("%s: Invalid gpio: %d\n", __func__, pdata->hac_pa_gpio); return false; } pr_err("%s: %s fuhua HAC PA\n", __func__, enable ? "Enable" : "Disable"); if (enable) { for( i=0 ; i<extamp_mode ; i++) { ret = msm_cdc_pinctrl_select_sleep_state(pdata->hac_pa_gpio_p); if (ret) { pr_err("%s: gpio set cannot be de-sleeped %s\n ",__func__,"lo_spk_gpio"); return ret; } udelay(2); ret = msm_cdc_pinctrl_select_active_state( pdata->hac_pa_gpio_p); if (ret) { pr_err("%s: gpio set cannot be de-activated %s\n", __func__, "lo_spk_gpio"); return ret; } pr_err("%s: %s i=%d\n ",__func__, enable ? "Enable" : "Disable",i); } gpio_set_value_cansleep(pdata->hac_pa_gpio, enable); } else { gpio_set_value_cansleep(pdata->hac_pa_gpio, enable); pr_err("%s: %s\n ",__func__, enable ? "Enable" : "Disable"); ret = msm_cdc_pinctrl_select_sleep_state( pdata->hac_pa_gpio_p); if (ret) { pr_err("%s: gpio set cannot be de-activated %s\n", __func__, "lo_spk_gpio"); return ret; } } return 0; } /*end mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */

其中定义了pa的模式，extamp_mode，剩下的主要操作就是通过Qcom的接口开关引脚了。
msm_cdc_pinctrl_select_active_state(pdata->hac_pa_gpio_p);
msm_cdc_pinctrl_select_sleep_state(pdata->hac_pa_gpio_p);
gpio_set_value_cansleep(pdata->hac_pa_gpio, enable);
但是控制的时候肯定不能直接指定端口嘛，这种太不便于管理了，我们是有管理的公司，要为后来的产品造福，不要写些烂代码，虽然繁琐。所以需要在probe的时候遍历一遍：

static int msm8952_asoc_machine_probe(struct platform_device *pdev) { struct snd_soc_card *card; struct msm_asoc_mach_data *pdata = NULL; const char *hs_micbias_type = "qcom,msm-hs-micbias-type"; const char *ext_pa = "qcom,msm-ext-pa"; const char *mclk = "qcom,msm-mclk-freq"; const char *wsa = "asoc-wsa-codec-names"; const char *wsa_prefix = "asoc-wsa-codec-prefixes"; const char *type = NULL; const char *ext_pa_str = NULL; const char *wsa_str = NULL; const char *wsa_prefix_str = NULL; const char *spk_ext_pa = "qcom,msm-spk-ext-pa"; /*begin mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ const char *hac_pa = "qcom,msm-hac-pa"; const char *hac_pa_p = "qcom,msm-hac-pa-gpio"; /*end mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ int num_strings; ... pr_debug("%s: ext_pa = %d\n", __func__, pdata->ext_pa); /*begin mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ pdata->hac_pa_gpio = of_get_named_gpio(pdev->dev.of_node, hac_pa, 0); if (pdata->hac_pa_gpio < 0) { dev_err(&pdev->dev, "%s: missing %s in dt node\n", __func__, hac_pa); } pdata->hac_pa_gpio_p = of_parse_phandle(pdev->dev.of_node, hac_pa_p, 0); if (pdata->hac_pa_gpio_p < 0) { dev_err(&pdev->dev, "%s: missing %s in dt node\n", __func__, hac_pa_p); } /*end mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ pdata->spk_ext_pa_gpio = of_get_named_gpio(pdev->dev.of_node, spk_ext_pa, 0); if (pdata->spk_ext_pa_gpio < 0) {

以上代码就是读取dts中的定义，那么dts中又添加了什么呢？(我是在kernel/msm-4.9/arch/arm64/boot/dts/qcom/qm215-audio.dtsi中添加的，当然可以选择其他地方)

/*begin mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ &tlmm { hac_pa { hac_pa_high: hac_pa_high { mux { pins = "gpio127"; function = "gpio"; }; config { pins = "gpio127"; drive-strength = <8>; /* 8mA */ bias-disable = <0>; /* no pull */ output-high; }; }; hac_pa_low: hac_pa_low { mux { pins = "gpio127"; function = "gpio"; }; config { pins = "gpio127"; drive-strength = <2>; output-low; bias-pull-down; }; }; }; }; /*end mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ &soc { qcom,msm-audio-apr { compatible = "qcom,msm-audio-apr"; msm_audio_apr_dummy { compatible = "qcom,msm-audio-apr-dummy"; }; }; qcom,avtimer@c0a300c { compatible = "qcom,avtimer"; reg = <0x0c0a300c 0x4>, <0x0c0a3010 0x4>; reg-names = "avtimer_lsb_addr", "avtimer_msb_addr"; qcom,clk-div = <27>; }; /*begin mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ cdc_hac_pa_gpio: msm_cdc_pinctrl@127 { compatible = "qcom,msm-cdc-pinctrl"; pinctrl-names = "aud_active", "aud_sleep"; pinctrl-0 = <&hac_pa_high>; pinctrl-1 = <&hac_pa_low>; }; /*end mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ int_codec: sound { status = "okay"; compatible = "qcom,msm8952-audio-codec"; qcom,model = "msm8952-snd-card-mtp"; reg = <0xc051000 0x4>, <0xc051004 0x4>, <0xc055000 0x4>, <0xc052000 0x4>; reg-names = "csr_gp_io_mux_mic_ctl", "csr_gp_io_mux_spkr_ctl", "csr_gp_io_lpaif_pri_pcm_pri_mode_muxsel", "csr_gp_io_mux_quin_ctl"; qcom,msm-ext-pa = "primary"; /*begin mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ qcom,msm-hac-pa = <&tlmm 127 0>; qcom,msm-hac-pa-gpio = <&cdc_hac_pa_gpio>; /*end mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ qcom,msm-mclk-freq = <9600000>; qcom,msm-mbhc-hphl-swh = <1>; qcom,msm-mbhc-gnd-swh = <1>;

这些添加完成之后，基本上就能通过tinyalsa去控制“HAC_PA”的On/Off了，达到想打开GPIO_HAC_EN的时候就能打开。

d

那么硬件的同事还有两个需求，第一个就是配对一个acdb_id,这样能方便他们配对调试，那么在hal层需要做什么呢?(目录：hardware/qcom/audio)由于比较零散，也比较简单，知识点不多，所以直接贴上diff文件吧，这一份是比较早的代码备份，有一点逻辑是有问题的。文件直接通过git diff ./ > diff.txt导出来就可以了。

diff --git a/hal/audio_hw.c b/hal/audio_hw.c index 3404dd6..bed0ec3 100644 --- a/hal/audio_hw.c +++ b/hal/audio_hw.c @@ -6866,6 +6866,23 @@ static int adev_set_parameters(struct audio_hw_device *dev, const char *kvpairs) status = platform_set_parameters(adev->platform, parms); if (status != 0) goto done; +/*begin mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ + ret = str_parms_get_str(parms, "odm.hac.enable", value, sizeof(value)); + if(ret >= 0) + { + ALOGE("fuhua ---- get odm.hac.enable = %s",value); + if(strcmp(value,AUDIO_PARAMETER_VALUE_ON) == 0) + {adev->hac_enable = true;} + else + {adev->hac_enable = false;} + } + else + { + ALOGE("fuhua ---- not get the odm.hac.enable = %s",value); + } + +/*end mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ + ret = str_parms_get_str(parms, AUDIO_PARAMETER_KEY_BT_NREC, value, sizeof(value)); if (ret >= 0) { diff --git a/hal/audio_hw.h b/hal/audio_hw.h index f791b6a..3865c0f 100644 --- a/hal/audio_hw.h +++ b/hal/audio_hw.h @@ -493,6 +493,9 @@ struct audio_device { bool allow_afe_proxy_usage; bool is_charging; // from battery listener bool mic_break_enabled; + /*begin mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ + bool hac_enable; + /*end mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ int snd_card; card_status_t card_status; diff --git a/hal/msm8916/platform.c b/hal/msm8916/platform.c index aeb3abe..7a8d94e 100644 --- a/hal/msm8916/platform.c +++ b/hal/msm8916/platform.c @@ -488,7 +488,9 @@ static const char * const device_table[SND_DEVICE_MAX] = { [SND_DEVICE_OUT_VOIP_SPEAKER] = "voip-speaker", [SND_DEVICE_OUT_VOIP_HEADPHONES] = "voip-headphones", #endif - + /*begin mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ + [SND_DEVICE_OUT_VOICE_HANDSET_HAC] = "voice-handset-hac", + /*end mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ /* Capture sound devices */ [SND_DEVICE_IN_HANDSET_MIC] = "handset-mic", [SND_DEVICE_IN_HANDSET_MIC_EXTERNAL] = "handset-mic-ext", @@ -668,6 +670,9 @@ static int acdb_device_table[SND_DEVICE_MAX] = { [SND_DEVICE_OUT_VOIP_SPEAKER] = 132, [SND_DEVICE_OUT_VOIP_HEADPHONES] = 134, #endif + /*begin mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ + [SND_DEVICE_OUT_VOICE_HANDSET_HAC] = 31, + /*end mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ [SND_DEVICE_IN_HANDSET_MIC] = 4, [SND_DEVICE_IN_HANDSET_MIC_EXTERNAL] = 4, @@ -832,6 +837,10 @@ static struct name_to_index snd_device_name_index[SND_DEVICE_MAX] = { {TO_NAME_INDEX(SND_DEVICE_OUT_VOIP_SPEAKER)}, {TO_NAME_INDEX(SND_DEVICE_OUT_VOIP_HEADPHONES)}, #endif + /*begin mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ + {TO_NAME_INDEX(SND_DEVICE_OUT_VOICE_HANDSET_HAC)}, + /*end mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ + {TO_NAME_INDEX(SND_DEVICE_IN_HANDSET_MIC)}, {TO_NAME_INDEX(SND_DEVICE_IN_HANDSET_MIC_EXTERNAL)}, {TO_NAME_INDEX(SND_DEVICE_IN_HANDSET_MIC_AEC)}, @@ -4307,6 +4316,18 @@ snd_device_t platform_get_output_snd_device(void *platform, struct stream_out *o snd_device = SND_DEVICE_OUT_ANC_HANDSET; else snd_device = SND_DEVICE_OUT_VOICE_HANDSET; + /*begin mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ + if(adev->hac_enable == true) + { + ALOGE("fuhua --- adev->hac_enable == true"); + snd_device = SND_DEVICE_OUT_VOICE_HANDSET_HAC; + } + else + { + ALOGE("fuhua --- adev->hac_enable == false or not get value"); + snd_device = SND_DEVICE_OUT_VOICE_HANDSET_HAC; + } + /*end mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ } else if (devices & AUDIO_DEVICE_OUT_TELEPHONY_TX) snd_device = SND_DEVICE_OUT_VOICE_TX; diff --git a/hal/msm8916/platform.h b/hal/msm8916/platform.h index f37819d..e0dbcfa 100644 --- a/hal/msm8916/platform.h +++ b/hal/msm8916/platform.h @@ -150,6 +150,9 @@ enum { SND_DEVICE_OUT_VOIP_SPEAKER, SND_DEVICE_OUT_VOIP_HEADPHONES, #endif + /*begin mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ + SND_DEVICE_OUT_VOICE_HANDSET_HAC, + /*end mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ SND_DEVICE_OUT_VOICE_SPEAKER_AND_VOICE_HEADPHONES, SND_DEVICE_OUT_VOICE_SPEAKER_AND_VOICE_ANC_HEADSET, SND_DEVICE_OUT_VOICE_SPEAKER_STEREO_AND_VOICE_HEADPHONES, @@ -292,8 +295,10 @@ enum { #define MIXER_PATH_MAX_LENGTH 100 #define SND_CARD_MAX_LENGTH 100 #define CODEC_VERSION_MAX_LENGTH 100 - -#define MAX_VOL_INDEX 5 +/*begin mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ +//#define MAX_VOL_INDEX 5 +#define MAX_VOL_INDEX 7 +/*end mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 */ #define MIN_VOL_INDEX 0 #define percent_to_index(val, min, max) \ ((val) * ((max) - (min)) * 0.01 + (min) + .5)

e

完成audio_test.sh中添加开关。实际上只要打通了 HAC_PA 的path，剩下的都不难了吧。

1. ###################### receiver playback test ###################### if [ $1 == 'handset' ];then # echo $$ >> /data/audio_test_receiver.pid # echo 'log log ' >> /sdcard/log.txt # setprop "tinyplay_status" "on" tinymix_v2 'PRI_MI2S_RX Audio Mixer MultiMedia1' '1' tinymix_v2 'RX1 MIX1 INP1' 'RX1' tinymix_v2 "RDAC2 MUX" 'RX1' tinymix_v2 'RX1 Digital Volume' '84' tinymix_v2 "EAR PA Gain" "POS_6_DB" tinymix_v2 "EAR_S" 'Switch' #begin mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 tinymix_v2 "HAC_PA" 'On' #end mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 while [ "1" == "1" ] do tinyplay_v2 /system/etc/112.wav -d 0 done fi if [ $1 == 'handset-stop' ];then # setprop "tinyplay_status" "off" # if [ -f /data/audio_test_receiver.pid ];then # pid=`cat /data/audio_test_receiver.pid` # kill -9 $pid # rm /data/audio_test_receiver.pid # fi #begin mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 tinymix_v2 "HAC_PA" 'Off' #end mod by fuhua for task: 8668750 on 2019-12-03 task id :8668750 tinymix_v2 'RX1 MIX1 INP1' '0' tinymix_v2 "RDAC2 MUX" 'ZERO' tinymix_v2 'RX1 Digital Volume' '67' tinymix_v2 "EAR PA Gain" 'POS_1P5_DB' tinymix_v2 "EAR_S" 'ZERO' tinymix_v2 'PRI_MI2S_RX Audio Mixer MultiMedia1' '0' fi

结语

1. 那么至此，整个hac器件的bring up就告一段落了，剩下的可能是一些维护工作？
   我在自己调试的时候发现，单单的没有tinymix_v2 "EAR PA Gain" "POS_6_DB"增益的设置，打电话的时候是不会出声的，向硬件同事请教，说是由于电信号转磁信号效率低，而hac器件还得从磁信号又转一遍电信号，那更低了；而电信号转机械信号效率相对较高，即Receiver能出声而hac器件不能出声的道理。
2. 期间，发现hac器件噪声严重，由于布局的原因，加上屏幕的干扰，实际上是有干扰的，背光的信号频率很高。