给自己的电脑添加虚拟网卡

控制面板进入添加硬件向导,

添加新硬件,检测过后选择添加新设备,再选择从列表中选取,选中网卡,

按下一步,查找制造商Microsoft有一个设备Microsoft Loopback Adapter,

选中它,安装完成。

右击我的电脑——属性,点击硬件,查看设备管理器,会多出一个新网卡,这就是虚拟网卡。

虚拟网卡驱动源代码(原版): /* * snull.c -- the Simple Network Utility * * Copyright (C) 2001 Alessandro Rubini and Jonathan Corbet * Copyright (C) 2001 O'Reilly & Associates * * The source code in this file can be freely used, adapted, * and redistributed in source or binary form, so long as an * acknowledgment appears in derived source files. The citation * should list that the code comes from the book "Linux Device * Drivers" by Alessandro Rubini and Jonathan Corbet, published * by O'Reilly & Associates. No warranty is attached; * we cannot take responsibility for errors or fitness for use. * * $Id: snull.c,v 1.21 2004/11/05 02:36:03 rubini Exp $ */ #include #include #include #include #include #include /* printk() */ #include /* kmalloc() */ #include /* error codes */ #include /* size_t */ #include /* mark_bh */ #include #include /* struct device, and other headers */ #include /* eth_type_trans */ #include /* struct iphdr */ #include /* struct tcphdr */ #include #include "snull.h" #include #include MODULE_AUTHOR("Alessandro Rubini, Jonathan Corbet"); MODULE_LICENSE("Dual BSD/GPL"); /* * Transmitter lockup simulation, normally disabled. */ static int lockup = 0; module_param(lockup, int, 0); static int timeout = SNULL_TIMEOUT; module_param(timeout, int, 0); /* * Do we run in NAPI mode? */ static int use_napi = 0; module_param(use_napi, int, 0); /* * A structure representing an in-flight packet. */ struct snull_packet { struct snull_packet *next; struct net_device *dev; int datalen; u8 data[ETH_DATA_LEN]; }; int pool_size = 8; module_param(pool_size, int, 0); /* * This structure is private to each device. It is used to
在Ubuntu系统中,可以使用以下步骤将真实网卡的网络共享给虚拟网卡: 1. 打开终端并输入以下命令,以查看现有的网络接口和IP地址: ``` ifconfig ``` 2. 确定真实网卡的名称,例如 eth0。 3. 安装并配置 dnsmasq 软件包,它是一个轻量级的 DNS 和 DHCP 服务器,用于为虚拟网卡分配 IP 地址和域名解析。执行以下命令: ``` sudo apt-get install dnsmasq ``` 4. 编辑 dnsmasq 配置文件 /etc/dnsmasq.conf,在文件末尾添加以下内容: ``` interface=<虚拟网卡名称> dhcp-range=<虚拟网卡IP池起始地址>,<虚拟网卡IP池结束地址>,<子网掩码>,<租约时间> ``` 其中,<虚拟网卡名称> 是你创建的虚拟网卡的名称,<虚拟网卡IP池起始地址> 和 <虚拟网卡IP池结束地址> 是你想要为虚拟网卡分配的 IP 地址范围,<子网掩码> 是你的网络子网掩码,<租约时间> 是分配给每个 IP 地址的租用时间。 例如,如果你想要为虚拟网卡分配的 IP 地址范围是 192.168.100.2 到 192.168.100.100,子网掩码是 255.255.255.0,租约时间是 12 小时,那么配置文件应该是这样的: ``` interface=eth1 dhcp-range=192.168.100.2,192.168.100.100,255.255.255.0,12h ``` 5. 启动 dnsmasq 服务并设置开机自启动。执行以下命令: ``` sudo systemctl start dnsmasq sudo systemctl enable dnsmasq ``` 6. 启用 IP 转发功能。打开 /etc/sysctl.conf 文件并找到以下行: ``` #net.ipv4.ip_forward=1 ``` 去掉注释并将其修改为: ``` net.ipv4.ip_forward=1 ``` 保存并关闭文件。 7. 使用 iptables 命令设置网络地址转换(NAT)规则,将虚拟网卡上的流量转发到真实网卡。执行以下命令: ``` sudo iptables -t nat -A POSTROUTING -o <真实网卡名称> -j MASQUERADE ``` 其中,<真实网卡名称> 是你的真实网卡名称。 8. 最后,重启网络服务以使更改生效。执行以下命令: ``` sudo service networking restart ``` 现在,你应该能够使用虚拟网卡连接到 Internet,因为它可以共享真实网卡的网络连接。
评论
添加红包

请填写红包祝福语或标题

红包个数最小为10个

红包金额最低5元

当前余额3.43前往充值 >
需支付:10.00
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明:

1.余额是钱包充值的虚拟货币,按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载,可以购买VIP、付费专栏及课程。

余额充值