USB设备类型代码以及详细说明

版权声明：本文为博主原创文章，未经博主允许不得转载。

目录(?)[+]

说明:由于链接是相对路径,下载和点击会不正常,如果需要下载文中提到的文档,请去官方网站相关地址下载

以下是USB所有支持的设备类型代码.

地址:http://www.usb.org/developers/defined_class

USB Class Codes                    

November 17, 2009

 

USB defines class code information that is used to identify a device’s functionality and to nominally load a device driver based on that functionality. The information is contained in three bytes with the names Base Class, SubClass, and Protocol. (Note that ‘Base Class’ is used in this description to identify the first byte of the Class Code triple. That terminology is not used in the USB Specification). There are two places on a device where class code information can be placed.One place is in the Device Descriptor, and the other is in Interface Descriptors. Some defined class codes are allowed to be used only in a Device Descriptor, others can be used in both Device and Interface Descriptors, and some can only be used in Interface Descriptors. The table below shows the currently defined set of  Base Class values, what the generic usage is, and where that Base Class can be used (either Device or Interface Descriptors or both).

 

 

Base Class	Descriptor Usage	Description
00h	Device	Use class information in the Interface Descriptors
01h	Interface	Audio
02h	Both	Communications and CDC Control
03h	Interface	HID (Human Interface Device)
05h	Interface	Physical
06h	Interface	Image
07h	Interface	Printer
08h	Interface	Mass Storage
09h	Device	Hub
0Ah	Interface	CDC-Data
0Bh	Interface	Smart Card
0Dh	Interface	Content Security
0Eh	Interface	Video
0Fh	Interface	Personal Healthcare
DCh	Both	Diagnostic Device
E0h	Interface	Wireless Controller
EFh	Both	Miscellaneous
FEh	Interface	Application Specific
FFh	Both	Vendor Specific

 

 

Base Class 00h (Device)

This base class is defined to be used in Device Descriptors to indicate that class information should be determined from the Interface Descriptors in the device. There is one class code definition in this base class.  All other values are reserved.

 

This value is also used in Interface Descriptors to indicate a null class code triple.

 

 

Base Class	SubClass	Protocol	Meaning
00h	00h	00h	Use class code info from Interface Descriptors

 

Base Class 01h (Audio)

This base class is defined for Audio capable devices that conform to the Audio Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values. Values outside of that defined spec are reserved. These class codes may only be used in Interface Descriptors.

 

 

Base Class	SubClass	Protocol	Meaning
01h	xxh	xxh	Audio device

 

 

Base Class 02h (Communications and CDC Control)

 

This base class is defined for devices that conform to the Communications Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values. Values outside of that defined spec are reserved.  Note that the Communication Device Class spec requires some class code values (triples) to be used in Device Descriptors and some to be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
02h	xxh	xxh	Communication device class

 

Base Class 03h (HID – Human Interface Device)

This base class is defined for devices that conform to the HID Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values.   Values outside of that defined spec are reserved. These class codes can only be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
03h	xxh	xxh	HID device class

 

Base Class 05h (Physical)

This base class is defined for devices that conform to the Physical Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values.  Values outside of that defined spec are reserved. These class codes can only be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
05h	xxh	xxh	Physical device class

 

 

Base Class 06h (Still Imaging)

This base class is defined for devices that conform to the Imaging Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values.   Values outside of that defined spec are reserved.

 

Base Class	SubClass	Protocol	Meaning
06h	01h	01h	Still Imaging device

 

 

Base Class 07h (Printer)

This base class is defined for devices that conform to the Printer Device Class Specification found on the USB-IF website.  That specification defines the usable set of SubClass and Protocol values.  Values outside of that defined spec are reserved.  These class codes can only be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
07h	xxh	xxh	Printer device

 

 

Base Class 08h (Mass Storage)

This base class is defined for devices that conform to the Mass Storage Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values. Values outside of that defined spec are reserved. These class codes can only be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
08h	xxh	xxh	Mass Storage device

 

 

Base Class 09h (Hub)

This base class is defined for devices that are USB hubs and conform to the definition in the USB specification.  That specification defines the complete triples as shown below.  All other values are reserved.  These class codes can only be used in Device Descriptors.

 

Base Class	SubClass	Protocol	Meaning
09h	00h	00h	Full speed Hub
		01h	Hi-speed hub with single TT
		02h	Hi-speed hub with multiple TTs

 

 

Base Class 0Ah (CDC-Data)

This base class is defined for devices that conform to the Communications Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values.Values outside of that defined spec are reserved. These class codes can only be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
0Ah	xxh	xxh	CDC data device

 

 

Base Class 0Bh (Smart Card)

This base class is defined for devices that conform to the Smart Card Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values.Values outside of that defined spec are reserved. These class codes can only be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
0Bh	xxh	xxh	Smart Card device

 

 

Base Class 0Dh (Content Security)

This base class is defined for devices that conform to the Content Security Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values. Values outside of that defined spec are reserved. These class codes can only be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
0Dh	00h	00h	Content Security device

 

 

Base Class 0Eh (Video)

This base class is defined for devices that conform to the Video Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values. Values outside of that defined spec are reserved. These class codes can only be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
0Eh	xxh	xxh	Video device

 

 

Base Class 0Fh (Personal Healthcare)

This base class is defined for devices that conform to the Personal Healthcare Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values. Values outside of that defined spec are reserved. These class codes should only be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
0Fh	xxh	xxh	Personal Healthcare device

 

 

Base Class DCh (Diagnostic Device)

This base class is defined for devices that diagnostic devices. There is currently only one value defined. All other values are reserved. This class code can be used in Device or Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
DCh	01h	01h	USB2 Compliance Device.  Definition for this device can be found at http://www.intel.com/technology/usb/spec.htm

 

 

Base Class E0h (Wireless Controller)

This base class is defined for devices that are Wireless controllers. Values not shown in the table below are reserved. These class codes are to be used in Interface Descriptors, with the exception of the Bluetooth class code which can also be used in a Device Descriptor. 

 

Base Class	SubClass	Protocol	Meaning
E0h	01h	01h	Bluetooth Programming Interface.  Get specific information from www.bluetooth.com.
		02h	UWB Radio Control Interface.  Definition for this is found in the Wireless USB Specification in Chapter 8.
		03h	Remote NDIS.  Information can be found at: http://www.microsoft.com/windowsmobile/mobileoperators/default.mspx
		04h	Bluetooth AMP Controller. Get specific information from www.bluetooth.com.
	2h	01h	Host Wire Adapter Control/Data interface.  Definition can be found in the Wireless USB Specification in Chapter 8.
		02h	Device Wire Adapter Control/Data interface.  Definition can be found in the Wireless USB Specification in Chapter 8.
		03h	Device Wire Adapter Isochronous interface.  Definition can be found in the Wireless USB Specification in Chapter 8.

 

Base Class EFh (Miscellaneous)

This base class is defined for miscellaneous device definitions. Values not shown in the table below are reserved.  The use of these class codes (Device or Interface descriptor) are specifically annotated in each entry below.

 

 

Base Class	SubClass	Protocol	Meaning
EFh	01h	01h	Active Sync device.  This class code can be used in either Device or Interface Descriptors.  Contact Microsoft for more information on this class.
		02h	Palm Sync.  This class code can be used in either Device or Interface Descriptors.
	02h	01h	Interface Association Descriptor.  The usage of this class code triple is defined in the Interface Association Descriptor ECN that is provided on www.usb.org .  This class code may only be used in Device Descriptors.
		02h	Wire Adapter Multifunction Peripheral programming interface. Definition can be found in the Wireless USB Specification in Chapter 8.  This class code may only be used in Device Descriptors
	03h	01h	Cable Based Association Framework.  This is defined in the Association Model addendum to the Wireless USB specification.  This class code may only be used in Interface Descriptors.

 

 

 

Base Class FEh (Application Specific)

This base class is defined for devices that conform to several class specifications found on the USB-IF website.  That specification defines the usable set of SubClass and Protocol values.  Values outside of that defined spec are reserved.  These class codes can only be used in Interface Descriptors.

 

 

Base Class	SubClass	Protocol	Meaning
FEh	01h	01h	Device Firmware Upgrade.  Device class definition provided on www.usb.org .
	02h	00h	IRDA Bridge device.  Device class definition provided on www.usb.org .
	03h	00h	USB Test and Measurement Device.  Definition provided in the USB Test and Measurement Class spec found on www.usb.org .
		01h	USB Test and Measurement Device conforming to the USBTMC USB488 Subclass Specification found on www.usb.org.

 

 

Base Class FFh (Vendor Specific)

This base class is defined for vendors to use as they please.  These class codes can be used in both Device and Interface Descriptors.

 

 

Base Class	SubClass	Protocol	Meaning
FFh	xxh	xxh	Vendor specific

 

以下是相关类型的详细说明:

地址:http://www.usb.org/developers/devclass_docs

Approved Class Specification Documents 

If you have questions regarding any of these documents please contact the DWG chair (dwg-wg-chair@usb.org) and your questions will be channeled to the appropriate group.

Audio Class

Audio Device Class Spec for Basic Audio Devices and Adopters Agreement (.zip format, size 1.33MB)
Audio Device Document 1.0 
Audio Data Formats 1.0 
Audio Terminal Types 1.0 
USB MIDI Devices 1.0 
Audio Devices Rev. 2.0 Spec and Adopters Agreement (.zip format, size 1.28MB) 

Battery Charging

Battery Charging v1.1 Spec and Adopters Agreement (.zip format, size 292 KB)

Cable and Connector

Cable and Connector Class 2.0 
Series 'A' Plug form factor Guideline 1.0 
USB Connector for Mezzanine Applications Guidelines Rev. 1.0 
Micro-USB Cables and Connectors v1.01 Spec and Adopters Agreement

Common Class (CCS)

Common Class Base Specification 1.0

Communications Device Class

Class definitions for Communication Devices 1.2 (.zip file format, size 2.61 MB)
the components of CDC 1.1 have been reorganized as five separate documents:
ATM120.pdf -- CDC Subclass for Asynchronous Transfer Mode Devices
CDC120.pdf -- CDC Subclass for Communications Devices
ECM120.pdf -- CDC Subclass for Ethernet Control Model Devices
ISDN120.pdf -- CDC Subclass for ISDN Devices
PSTN120.pdf -- CDC Subclass for PSTN devices
CDC Subclass for Wireless Mobile Communication Devices 1.1
CDC v1.2 WMC v1.1 Adopters Agreement

CDC Subclass Specification for Ethernet Emulation Model Devices 1.0

Network Control Model Devices Specification v1.0 and Adopters Agreement (.zip format, size 492 KB)

Content Security

Device Class Definition for Content Security Devices 1.0 
Content Security Method 1 - Basic Authentication Protocol 1.0 
Content Security Method 2 - USB Digital Transmission Content Protection Implementation 1.0

Device Firmware Upgrade Group

Device Firmware Upgrade 1.1 (new version 31-Aug-2004)

HID Class

HID Information

Imaging Class

Still Image Capture Device Definition 1.0 and Errata as of 16-Mar-2007 (.zip format, size 200 KB)

IrDA

IrDA Bridge Device Definition 1.0

Mass Storage

Mass Storage Class Specification Overview 1.3 
Mass Storage Bulk Only 1.0 
Mass Storage Control/Bulk/Interrupt (CBI) Specification 1.1  
Mass Storage UFI Command Specification 1.0 
Mass Storage Bootability Specification 1.0 
Lockable Mass Storage Specification 1.0 and Adopters Agreement (.zip format, size 288 KB)
  - Lockable Mass Storage IP Disclosure

Media Transfer Protocol

Media Transfer Protocol v.1.0 Spec and MTP v.1.0 Adopters Agreement (.zip format, size 1.86MB)

Monitor

Monitor Device Document 1.0

OpenUSBDI

OpenUSBDI Specification 1.0

Personal Healthcare

Personal Healthcare Rev. 1.0, Errata for USB Personal Health Care Device Class and Personal Healthcare Adopters Agreement (.zip format, size 386 KB)

Physical Interface Devices

Device Class Definition for PID 1.0

Power

Power Device Class Document 1.0

Printer Class

Printer Device Class Document 1.1

Smart Card Class

Smart Card CCID version 1.1 
Smart Card ICCD version 1.0  

Test & Measurement Class

Test & Measurement Class Specifications

Video Class

Video Class 1.1 document set
    USB_Video_Class_1.1
    USB_Video_Identifiers_1.1
    USB_Video_Payload_DV_1.1
    USB_Video_Payload_Frame_Based_1.1
    USB_Video_Payload_MJPEG_1.1
    USB_Video_Payload_MPEG-2_TS_1.1
    USB_Video_Payload_Uncompressed_1.1
    USB_Video_Payload_Stream_Based_1.1
    USB_Video_Transport_1.1
    USB_Video_Example_1.1
    USB_Video_FAQ_1.1

Draft Class Specification Documents

PC Legacy Compatibility Specification 0.9

USB_Video_Compliance_1.09b -- draft for public review