海思双网卡冗余配置

1、海思PCIE设置成RC模式外接PCIE设备，内核配置
Bus support->PCI Express Port Bus support
Bus support-> Root Port Advanced Error Reporting support
Bus support-> PCI Express ASPM control
Bus support-> Hisilicon PCI Express support
Bus support → Hisilicon PCI Express support → PCI Express configs-> limit pcie max read request size     

2、海思外接PCIE网卡，内核配置
Device Drivers->Network device support -> Ethernet driver support -> Intel(R) PRO/1000 PCI-Express Gigabit Ethernet support
海思网络双冗余内核配置
Device Drivers->Network device support->Bonding driver support
双冗余模式内核配置
Device Drivers->Network device support-> Ethernet team driver support

3、配置完成后重新编译内核，在新内核下通过命令lspci可以查看pcie设备信息如下:
~ # lspci
00:00.0 Class 0604: 19e5:3559
01:00.0 Class 0200: 8086:10d3

4、海思网卡双冗余配置命令
ifconfig -a查看当前所有网口信息
~ # ifconfig -a
bond0     Link encap:Ethernet  HWaddr A2:7C:89:FF:CD:57  
          BROADCAST MASTER MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

eth0      Link encap:Ethernet  HWaddr E6:3F:86:A6:4B:7B  
          inet addr:192.168.24.46  Bcast:192.168.24.255  Mask:255.255.255.0
          inet6 addr: fe80::e43f:86ff:fea6:4b7b/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:10484 errors:0 dropped:537 overruns:0 frame:0
          TX packets:2001 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:9939854 (9.4 MiB)  TX bytes:168340 (164.3 KiB)
          Interrupt:43 

eth1      Link encap:Ethernet  HWaddr 68:05:CA:19:31:51  
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:50 Memory:30880000-308a0000 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:8 errors:0 dropped:0 overruns:0 frame:0
          TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1 
          RX bytes:896 (896.0 B)  TX bytes:896 (896.0 B)

网口双冗余绑定：
ifconfig bond0 down
ifconfig eth0 down
ifconfig eth1 down

modprobe bonding mode=0 miimon=100
参数说明：
mode:
0 for balance-rr
1 for active-backup
2 for balance-xor
3 for broadcast
4 for 802.3ad
5 for balance-tlb
6 for balance-alb

miimon:切换时间单位ms

                       
ifconfig bond0 192.168.24.46 netmask 255.255.255.0 up
ifenslave bond0 eth0 eth1
route add default gw 192.168.24.254

5、 查看冗余网卡绑定信息：
/sys/devices/platform/soc/0.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/net/eth1 # cat /proc/net/bonding/bond0 
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)

Bonding Mode: load balancing (round-robin)
MII Status: up
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0

Slave Interface: eth0
MII Status: up
Speed: 1000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: e6:3f:86:a6:4b:7b
Slave queue ID: 0

Slave Interface: eth1
MII Status: up
Speed: 1000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: 68:05:ca:19:31:51
Slave queue ID: 0