提示：文章写完后，目录可以自动生成，如何生成可参考右边的帮助文档
前言
提示：这里可以添加本文要记录的大概内容：
例如：随着人工智能的不断发展，机器学习这门技术也越来越重要，很多人都开启了学习机器学习，本文就介绍了机器学习的基础内容。
提示：以下是本篇文章正文内容，下面案例可供参考
一、IIC协议是什么？
IIC,即I²C，全称 Inter-Integrated Circuit，字面上的意思是集成电路之间，它其实是I²C Bus简称，所以中文应该叫 集成电路总线 ，它是一种串行通信总线，使用多主从架构，由飞利浦公司在1980年代为了让主板、嵌入式系统或手机用以连接低速周边设备而发展。（百度百科）
main.c
代码如下（示例）：
2.读入数据
#include "stm32f10x.h"
#include "usart.h"
#include "Delay.h"
#include <stdio.h>
#include "led.h"
#include "systick.h"
#include "HC_SR04.h"
#include "motor.h"
#include "oled.h"
int main()
{
unsigned int i;
I2C_Configuration();//I2C初始化
Oled_Iint();//产家给的OLED初始化代码
ms_Delay(2000);
Oled_Fill(0xff);//屏幕点亮
ms_Delay(2000);
Oled_Fill(0x00);//全屏灭
ms_Delay(2000);
OLED_ShowStr(0,3,"LZG",1);
OLED_ShowStr(0,4,"Hello world",2);
while(1)
{
for(i=0;i<3;i++)
{
OLED_ShowCN(22+16*i,0,i);
}
}
}
oled.c
代码如下（示例）：
#include "oled.h"
#include "stm32f10x.h"
#include "Delay.h"
#include "codetab.h"
void I2C_Configuration(void)
{
I2C_InitTypeDef I2C_InitStructure;//I2C结构体
GPIO_InitTypeDef GPIO_InitSructure;//GPIO结构体
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_I2C1, ENABLE);
//PB6 SCL PB7 SDA
GPIO_InitSructure.GPIO_Mode= GPIO_Mode_AF_OD;
GPIO_InitSructure.GPIO_Pin = GPIO_Pin_6 | GPIO_Pin_7;
GPIO_InitSructure.GPIO_Speed= GPIO_Speed_50MHz;
GPIO_Init(GPIOB, &GPIO_InitSructure);
//IC2
I2C_DeInit(I2C1);
I2C_InitStructure.I2C_Ack = I2C_Ack_Enable; //应答使能
I2C_InitStructure.I2C_AcknowledgedAddress= I2C_AcknowledgedAddress_7bit;//配置指定地址长度为7位
I2C_InitStructure.I2C_ClockSpeed = 400000;//配置时钟速度为400kbit/s
I2C_InitStructure.I2C_DutyCycle = I2C_DutyCycle_2 ;//配置占空比为2:1
I2C_InitStructure.I2C_Mode = I2C_Mode_I2C;//配置为I2C模式
I2C_InitStructure.I2C_OwnAddress1= 0X30;//配置自身设备地址，可以随便配
I2C_Init(I2C1, &I2C_InitStructure);
I2C_Cmd(I2C1, ENABLE);
}
void I2C_WriteByte(uint8_t address,uint8_t data)
{
while(I2C_GetFlagStatus(I2C1, I2C_FLAG_BUSY));//检查I2C总线是否繁忙
I2C_GenerateSTART(I2C1,ENABLE); //开启I2C1总线
while( !I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_MODE_SELECT));//EV5主模式
I2C_Send7bitAddress(I2C1,OLED_ADDRESS,I2C_Direction_Transmitter);//发送器件地址
while( !I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED ));//EV6
I2C_SendData(I2C1 , address);//寄存器地址
while( !I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_BYTE_TRANSMITTING));//EV8
I2C_SendData(I2C1 , data);//发送数据
while( !I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_BYTE_TRANSMITTING));//EV8
I2C_GenerateSTOP(I2C1, ENABLE);//关闭I2C总线
}
//写命令
void WriteCmd(unsigned char I2C_Command)
{
I2C_WriteByte(0x00,I2C_Command);
}
//写数据
void WriteDat(unsigned char I2C_data)
{
I2C_WriteByte(0x40,I2C_data);
}
//OLED屏幕初始化
void Oled_Iint()
{
Delay(100);
WriteCmd(0xAE); //display off
WriteCmd(0x20); //Set Memory Addressing Mode
WriteCmd(0x10); //00,Horizontal Addressing Mode;01,Vertical Addressing Mode;10,Page Addressing Mode (RESET);11,Invalid
WriteCmd(0xb0); //Set Page Start Address for Page Addressing Mode,0-7
WriteCmd(0xc8); //Set COM Output Scan Direction
WriteCmd(0x00); //---set low column address
WriteCmd(0x10); //---set high column address
WriteCmd(0x40); //--set start line address
WriteCmd(0x81); //--set contrast control register
WriteCmd(0xff); //调节亮度，0x00~0xff
WriteCmd(0xa1); //--set segment re-map 0 to 127
WriteCmd(0xa6); //--set normal display
WriteCmd(0xa8); //--set multiplex ratio(1 to 64)
WriteCmd(0x3F); //
WriteCmd(0xa4); //0xa4,Output follows RAM content;0xa5,Output ignores RAM content
WriteCmd(0xd3); //-set display offset
WriteCmd(0x00); //-not offset
WriteCmd(0xd5); //--set display clock divide ratio/oscillator frequency
WriteCmd(0xf0); //--set divide ratio
WriteCmd(0xd9); //--set pre-charge period
WriteCmd(0x22); //
WriteCmd(0xda); //--set com pins hardware configuration
WriteCmd(0x12);
WriteCmd(0xdb); //--set vcomh
WriteCmd(0x20); //0x20,0.77xVcc
WriteCmd(0x8d); //--set DC-DC enable
WriteCmd(0x14); //
WriteCmd(0xaf); //--turn on oled panel
}
//设置起点坐标
void Oled_SetPos(unsigned char x,unsigned char y)
{
WriteCmd(0xb0 +y);//页地址
WriteCmd((x&0xf0)>>4|0x10);//列高地址
WriteCmd((x&0x0f)|0x01);//列低地址
}
//全屏填充
void Oled_Fill(unsigned char Fill_Data)
{
unsigned char m,n;
for(m=0;m<8;m++)
{
WriteCmd(0xb0+m);
WriteCmd(0x00);
WriteCmd(0x10);
for(n=0;n<128;n++)
{
WriteDat(Fill_Data);
}
}
}
//清屏
void Oled_CLS(void)
{
Oled_Fill(0x00);
}
//OLED打开
void Oled_ON(void)
{
WriteCmd(0x8D);//设置电荷泵
WriteCmd(0x14);//开启电荷泵
WriteCmd(0xAF);//设置显示开
}
//OLED关闭
void OLED_OFF(void)
{
WriteCmd(0x8D);//开启电荷泵
WriteCmd(0x13);//关闭电荷泵
WriteCmd(0xAE);//设置显示关
}
//显示字符串
void OLED_ShowStr(unsigned char x,unsigned char y,unsigned char ch[],unsigned char TextSize)
{
unsigned char c=0,i=0,j=0;
switch(TextSize)
{
case 1://8*6
{ while(ch[j]!='\0')
{
c=ch[j]-32;
if(x>122)
{
x=0;
y++;
}
Oled_SetPos(x,y);
for(i=0;i<6;i++)
{
WriteDat( F6x8[c][i] );
}
x+=6;
j++;
}
}break;
case 2://16*8
{
while(ch[j]!='\0')
{
c=ch[j]-32;
if(x>120)
{
x=0;
y++;
}
Oled_SetPos(x,y);
for(i=0;i<8;i++)
{
WriteDat( F8X16[c*16+i] );
}
Oled_SetPos(x,y+1);
for(i=0;i<8;i++)
{
WriteDat( F8X16[c*16+i+8] );
}
x+=8;
j++;
}
}
}
}
//显示中文,想要显示什么汉字，要用取模软件生成，放在codetab.h文件里
void OLED_ShowCN(unsigned char x,unsigned char y,unsigned char N)//N表示第几个汉字
{
unsigned char wm=0;
unsigned int addr=32*N;//一个汉字有32个Byte
Oled_SetPos(x,y);
for(wm=0;wm<16;wm++)
{
WriteDat(HZ1F16X16[addr]);
addr++;
}
Oled_SetPos(x,y+1);
for(wm=0;wm<16;wm++)
{
WriteDat( HZ1F16X16[addr]);
addr++;
}
}
//显示图片
void OLED_DrawBMP(unsigned char x0,unsigned char y0,unsigned char x1,unsigned char y1,unsigned char BMP[])
{
unsigned int j=0;
unsigned char x,y;
if(y1%8==0)
{
y=y1/8;
}
else
{
y=y1/8+1;
}
for(y=y0;y<y1;y++)
{
Oled_SetPos(x0,y0);
for(x=x0;x<x1;x++)
{
WriteDat(BMP[j]);
j++;
}
}
}oled.h
#ifndef _OLED_H_
#define _OLED_H_
#include "stm32f10x.h"
void I2C_Configuration(void);
void I2C_WriteByte(uint8_t address,uint8_t data);
void Writecmd(unsigned char I2C_Command);
void WriteDat(unsigned char I2C_data);
void Oled_Iint();
void Oled_SetPos(unsigned char x,unsigned char y);
void Oled_Fill(unsigned char Fill_Data);
void OLED_ShowStr(unsigned char x,unsigned char y,unsigned char ch[],unsigned char TextSize);
void OLED_ShowCN(unsigned char x,unsigned char y,unsigned char N);
void OLED_DrawBMP(unsigned char x0,unsigned char y0,unsigned char x1,unsigned char y1,unsigned char BMP[]);
#define OLED_ADDRESS 0x78
#endif
总结
注意字符和中文，要用取模软件进行取模，图形也要用相对于的取模软件取模，oled显示屏是八页，128列，其中每页又有8行，要注意向oled写入数据，是一竖一竖写，一竖就是一个byte，写完一竖自动跳转至下一竖开始写
1498
被折叠的 条评论
为什么被折叠?
到【灌水乐园】发言
