>Enable 进入特权模式
#Exit 返回上一级操作模式
#End 返回到特权模式
#write memory 或 copy running-config startup-config
保存配置文件
#del flash:config.text 删除配置文件 (交换机及 1700 系列路由器 )
#erase startup-config 删除配置文件 (2500 系列路由器 )
#del flash:vlan.dat 删除 Vlan 配置信息(交换机)
#Configure terminal 进入全局配置模式
(config)# hostname switchA
(config)#banner motd &
(config)#enable secret level 1 0 star 配置远程登陆密码为 star
(config)#enable secret level 15 0 star 配置特权密码为 star
Level 1 为普通用户级别,可选为 1~15 ,15 为最高权限级别; 0 表示密码不加密
(config)#enable services web-server 开启交换机 WEB 管理功能
Services 可选以下: web-server(WEB 管理 ) 、 telnet-server( 远程登陆 )等
配置设备名称为 switchA
配置每日提示信息 & 为终止符
查看所有端口信息
查看版本信息
查看交换机当前 MAC 地址表信息
查看信息
#show running-config
查看当前生效的配置信息
#show interface fastethernet 0/3 查看 F0/3 端口信息
查看 S1/2 端口信息
#show interface serial 1/2
#show interface
查看所有端口信息
#show ip interface brief
以简洁方式汇总查看所有端口信息
#show ip interface
#show version
#show mac-address-table
#show running-config
#show vlan
#show vlan id 10
#show interface fastethernet 0/1 switchport 查看某一端口模式 (如 F 0/1)
#show aggregateport 1 summary
#show spanning-tree
#show spanning-tree interface fastethernet 0/1 查看该端口的生成树状态
#show port-security
#show port-security address 查看地址安全绑定配置信息
#show ip access-lists listname 查看名为 listname 的列表的配置信息
#show access-lists
查看当前生效的配置信息
查看所有 VLAN 信息
查看某一 VLAN ( 如 VLAN10) 的信息
查看交换机的端口安全配置信息
查看聚合端口 AG1 的信息
查看生成树配置信息
端口的基本配置
(config)#Interface fastethernet 0/3 进入 F0/3 的端口配置模式
(config)#interface range fa 0/1-2,0/5,0/7-9 进入 F0/1 、F0/2 、F0/5、F0/7、F0/8、F0/9 的端
口配置模式
(config-if)#speed 10
(config-if)#duplex
适应 )
配置端口速率为 10M, 可选 10,100,auto
full 配置端口为全双工模式 ,可选 full( 全双工 ),half( 半双式 ),auto( 自
更多信息
l
开启该端口
(config-if)#no shutdown
(config-if)#switchport access vlan 10 将该端口划入 VLAN10 中, 用于 VLAN
(config-if)#switchport mode trunk
可选模式为 access , trunk
(config-if)#port-group 1
将该端口划入聚合端口 AG1 中 ,用于聚合端口
将该端口设为 trunk 模式 ,用于 Tag vlan
聚合端口的创建
(config)# interface aggregateport 1 创建聚合接口 AG1
(config-if)# switchport mode trunk
配置并保证 AG1 为 trunk 模式
(config)#int f0/23-24
(config-if-range)#port-group 1
将端口(端口组)划入聚合端口
AG1 中
生成树
(config)#spanning-tree
(config)#spanning-tree mode stp 指定生成树类型为 stp
可选模式 stp , rstp , mstp
(config)#spanning-tree priority 4096 设置交换机的优先级为 4096 , 优先级值小为高。优
开启生成树协议
先级可选值为 0,4096, 8192,,, ,为 4096 的倍数。交换机默认值为 32768
VLAN 的基本配置
(config)#vlan 10 创建 VLAN10
(config-vlan)#name vlanname 命名 VLAN 为 vlanname
(config-if)#switchport access vlan 10 将该端口划入 VLAN10 中
某端口的接口配置模式下进行
(config)#interface vlan 10 进入 VLAN 10 的虚拟端口配置模式
(config-if)# ip address 192.168.1.1 255.255.255.0 为 VLAN10 的虚拟端口配置 IP 及掩码,
二层交换机只能配置一个 IP,此 IP 是作为管理 IP 使用, 例如, 使用 Telnet 的方式登录的 IP
地址
(config-if)# no shutdown
启用该端口
端口安全
(config)# interface fastethernet 0/1
(config-if)# switchport port-security
1.配置最大连接数限制
(config-if)# switchport port-secruity maxmum 1 配置端口的最大连接数为 1,最大连接数
进入一个端口
开启该端口的安全功能
为 128
(config-if)# switchport port-secruity violation shutdown
配置安全违例的处理方式为 shutdown ,可选为 protect ( 当安全地址数满后,将未知名地
址丢弃 )、restrict( 当违例时,发送一个 Trap 通知 ) 、shutdown( 当违例时将端口关闭,并发送
Trap 通知,可在全局模式下用 errdisable recovery 来恢复 )
2. IP 和 MAC 地址绑定
(config-if)#switchport port-security mac-address xxxx.xxxx.xxxx ip-address 172.16.1.1
接口配置模式下配置 MAC 地址 xxxx.xxxx.xxxx 和 IP172.16.1.1 进行绑定 (MAC 地址注
意用小写 )
三层路由功能 (针对三层交换机 )
(config)# ip routing
(config)# interface fastethernet 0/1
(config-if)# no switchport
开启三层交换机的路由功能
开启端口的三层路由功能 (这样就可以为某一端口配置
IP)
(config-if)# ip address 192.168.1.1 255.255.255.0
(config-if)# no shutdown
三层交换机路由协议
(config)# ip route 172.16.1.0 255.255.255.0 172.16.2.1 配置静态路由
注 :172.16.1.0 255.255.255.0 为目标网络的网络号及子网掩码
172.16.2.1 为下一跳的地址,也可用接口表示 , 如 ip route 172.16.1.0 255.255.255.0 serial
1/2(172.16.2.0 所接的端口 )
(config)# router rip
(config-router)# network 172.16.1.0
(config-router)# version 2
开启 RIP 协议进程
申明本设备的直连网段信息
开启 RIP V2,可选为 version 1(RIPV1) 、 version
2(RIPV2)
(config-router)# no auto-summary
关闭路由信息的自动汇总功能 (只有在 RIPV2 支持 )
(config)# router ospf
(config)# router ospf 1
开启 OSPF 路由协议进程(针对 1762,无需使用进程 ID )
开启 OSPF 路由协议进程(针对 2501,需要加 OSPF 进程
ID )
列表
(config-router)# network 192.168.1.0 0.0.0.255 area 0
申明直连网段信息,并分配区域号 (area0 为骨干区域 )
IP ACL :
交换机采用命名的访问控制列表;分标准
1.标准 ACL
(stand) 和扩展 (extended)两种
(config)#ip access-list stand listname 定义命名标准列表,命名为 listname, stand 为标准
(config-std-nacl)#deny 192.168.30.0 0.0.0.255 拒绝来自 192.168.30.0 网段的 IP 流量通过
注: deny:拒绝通过;可选: deny(拒绝通过 )、 permit( 允许通过 )
192.168.30.0 0.0.0.255 :源地址及源地址通配符;可使用
(config-std-nacl)#permit any
(config-std-nacl)#end
2.扩展 ACL
(config)#ip access-list extended listname
定义命名扩展列表,命名为 listname,extended 为扩展
(config-ext-nacl)#deny
tcp 192.168.30.0 0.0.0.255 192.168.10.0 0.0.0.255 eq www 拒绝源
any 表示任何 IP
返回
地址为 192.168.30.0 网段的 IP 访问目的地址为 192.168.10.0 网段的 WWW 服务
注: deny:拒绝通过,可选: deny(拒绝通过 )、 permit( 允许通过 )
tcp: 协议名称,协议可以是 udp, ip, eigrp, gre, icmp, igmp, igrp 等等。
192.168.10.0 0.0.0.255 :源地址及源地址通配符
192.168.30.0 0.0.0.255 :目的地址及目的地址通配符
eq:操作符( lt-小于, eq-等于, gt-大于, neg- 不等于, range-包含)
www :端口号,可使用名称或具体编号
可以使用的协议名称(或编号)和端口名称(或编号)请打?查询。
(config-ext-nacl)#permit ip any any
(config-ext-nacl)#end
(config)#interface vlan 10
(config-if)# ip access-group listname in
进入端口配置模式
允许其它通过
返回
访问控制列表在端口下 in 方向应用;可选:in( 入
栈) 、 out( 出栈 )
(config-if)#end
注:配置 ACL 时,若只想对其中部分 IP 进行限制访问时,必须配置允许其流量通过,
返回
否则设备只会对限制 IP 进行处理,不会对非限制 IP 进行允许通过处理。
在锐捷交换机上配置 vrrp 、 arp 和 mstp
交换机
密码
1234(config)#enable secret level 1 0 100
1234(config)#enable secret level 15 0 100
远程登入密码
1234(config)#line vty 0 4
1234(config-line)#password 100
1234(config-line)#end
交换机管理 IP
1234(config)#interface vlan 1
1234(config-if)#ip address 192.168.1.10 255.255.255.0
1234(config-if)#no shutdown
修改交换机老化时间
1234(config)#mac-address-table aging-time 20
1234(config)#end
添删 vlan
1234(config)#vlan 888
1234(config-vlan)#name a888
1234(config)#no vlan 888
添加 access口
1234(config)#interface gigabitEthernet 0/10
1234(config-if)#switchport mode access
1234(config-if)#switchport access vlan 10
切换 assess trunk
1234(config-if)#switchport mode access
1234(config-if)#switchport mode trunk
指定特定一个 native vlan
1234(config-if)#switchport trunk native vlan 10
配置 trunk 口的许可 vlan 列表
Add VLANs to the current list
All VLANs
1234(config-if)#switchport trunk allowed vlan ?
add
all
except All VLANs except the following
remove Remove VLANs from the current list
速成树协议
1234(config)#spanning-tree
1234(config)#spanning-tree mode rstp/stp
配置网关:
switch(config)#ip default-gateway 192.168.1.254
交换机基本配置 - 常见查看命令
查看 CPU 利用率
show cpu
查看交换机时钟
show clock
查看交换机日志
show logging
查看交换机动态学习到的 MAC 地址表
show mac-address-table dynamic
查看当前交换机运行的配置文件
show running-config
查看交换机硬件、软件信息
show version
查看交换机的 arp 表
show arp
显示接口详细信息的命令
show interfaces gigabitEthernet 4/1 counters
接口配置
Switch(config)#interface gigabitethernet 0/1
把接口工作模式改为光口。
Switch(config-if)#medium-type fiber
把接口工作模式改为电口。
Switch(config-if)#medium-type copper
速度 /双工配置
进入接口配置模式。
Switch(config)#interface interface-id
设置接口的速率参数,或者设置为
auto。
Switch(config-if)#speed {10 | 100 | 1000 | auto }
设置接口的双工模式。
Switch(config-if)#duplex {auto | full | half}
例子
Switch(config)#interface gigabitethernet 0/1
Switch(config-if)#speed 1000
Switch(config-if)#duplex full
光口不能修改速度和双工配置,只能
在故障处理的时候, 如果遇到规律性的时断时续或掉包,
和对端设备的速率和双工模式不匹配,尤其是两端设备为不同厂商的时候。
VLAN
建立 VLAN 100
Switch (config)#vlan 100
该 VLAN 名称为 ruijie
auto。
在排除其他原因后, 可以考虑是否
Switch (config)#name ruijie
将交换机接口划入 VLAN 中:
range 表示选取了系列端口 1-48,这个对多个端口进行相同配置时非常有用。
Switch (config)#interface range f 0/1-48
将接口划到 VLAN 100 中。
Switch (config-if-range)#switchport access vlan 100
将接口划回到默认 VLAN 1 中,即端口初始配置。
Switch (config-if-range)#no switchport access vlan
Switch(config)#interface fastEthernet 0/1
该端口工作在 access模式下
Switch(config-if)#switchport mode access
该端口工作在 trunk 模式下
Switch(config-if)#switchport mode trunk
Switch(config)#interface fastEthernet 0/2
设定 VLAN 要修剪的 VLAN 。
Switch(config-if)#switchport trunk allowed vlan remove 2-9,11-19,21-4094
取消端口下的 VLAN 修剪。
Switch(config-if)#no switchport trunk allowed vlan
生成树
开启生成树协议。
Switch(config)#spanning-tree
禁止生成树协议。
Switch(config)#no spanning-tree
配置生成树优先级:
配置设备优先级为 4096。
Switch(config)#spanning-tree priority 4096
数值越低,优先级别越高。
端口镜像
配置 G0/2 为镜像端口。
Switch (config)# monitor session 1 destination interface G 0/2
配置 G0/1 为被镜像端口,且出入双向数据均被镜像。
Switch (config)# monitor session 1 source interface G 0/1 both
去掉镜像 1。
Switch (config)# no monitor session 1
端口聚合
Switch(config)#interface fastEthernet 0/1
把端口 f0/1 加入到聚合组 1 中。
Switch (config-if)#port-group 1
把端口 f0/1 从聚合组 1 中去掉
Switch (config-if)#no port-group 1
建立 ACL :
建立 ACL 访问控制列表名为 ruijie , extend 表示建立的是扩展访
Switch(config)# Ip access-list exten ruijie
问控制列表。
添加 ACL 的规则:
禁止 PING IP 地址为 192.168.1.1 的设备。
Switch (config-ext-nacl)#deny icmp any 192.168.1.1 255.255.255.0
禁止端口号为 135 的应用。
Switch (config-ext-nacl)# deny tcp any any eq 135
禁止协议为 www 的应用。
Switch (config-ext-nacl)#deny udp any any eq www
允许所有行为。
Switch(config-ext-nacl)# permit ip any any
将 ACL 应用到具体的接口上:
Switch (config)#interface range f 0/1
把名为 ruijie 的 ACL 应用到端口 f 0/1 上。
Switch (config-if)#ip access-group ruijie in
从接口去除 ACL 。
Switch (config-if)#no ip access-group ruijie in
删除 ACL:
删除名为 ruijie 的 ACL 。
Switch(config)#no Ip access-list exten ruijie
增加 ACE 项后,是增加到 ACL 最后,不可以中间插入,如果要调整
个删除 ACL 后再重新配置。
端口安全
ACE 的顺序,必须整
Switch (config)#interface range f 0/1
开启端口安全。
Switch(config-if)# switchport port-security
关闭端口安全。
Switch(config-if)# no switchport port-security
8。
设置端口能包含的最大安全地址数为
Switch(config-if)# switchport port-security maximum 8
在接口 fastethernet0/1 配置一个安全地址 00d0.f800.073c ,并为其绑定一个 IP 地址 192.168.1.1
Switch(config-if)# switchport port-security mac-address 00d0.f800.073c ip-address 192.168.1.1
删除接口上配置的安全地址。
Switch(config-if)#no switchport port-security mac-address 00d0.f800.073c ip-address 192.168.1.1
防 ARP 攻击
IP 和 MAC 地址的绑定
Switch(config)#arp ip-address hardware-address [type] interface-id
Switch(config)#arp 192.168.12.111 00d0.f800.073c arpa g 0/1
绑定网关
进入指定端口进行配置。
Switch(config)#Interface interface-id
配置防止 ip-address 的 ARP 欺骗。
Switch(config-if)#Anti-ARP-Spoofing ip ip-address
防 STP 攻击
进入端口 Fa0/1。
Switch(config)# inter fastEthernet 0/1
打开该端口的的 BPDU guard 功能。
Switch(config-if)# spanning-tree bpduguard enable
关闭该端口的的 BPDU guard 功能。
Switch(config-if)# spanning-tree bpduguard diaable
端口关闭后只能 shutdown 然后再 no shutdown
或者重新启动交换机才能恢复!
防 DOS/DDOS 攻击
进入端口 Fa0/1。
Switch(config)# inter fastEthernet 0/1
预防伪造源 IP 的 DOS 攻击的入口过滤功能。
Switch(config-if)#ip deny spoofing-source
关闭入口过滤功能只能在三层接口上配置。
Switch(config-if)#no ip deny spoofing-source
和 ACL 不能同时存在。
端口关闭后只能 shutdown 然后再 no shutdown
或者重新启动交换机才能恢复!
防 IP 扫描攻击配置:
打开系统保护。
Switch(config)#system-guard enable
关闭系统保护功能。
Switch(config)#no system-guard
DHCP 配置
打开 DHCP Relay Agent :
Switch(config)#service dhcp
配置 DHCP Server 的 IP 地址:
Switch(config)#ip helper-address address
VRRP 配置
Switch(config)#Interface interface-id
Switch(config-if)#Standby [group-number] ip ip-address
设置虚拟机的优先级。
standby [group-number] priority priority
三层交换机配置
SVI :
把 VLAN 10 配置成 SVI 。
switch (config)#interface vlan 10
给该 SVI 接口配置一个 IP 地址
switch (config-if)#ip address 192.168.1.1 255.255.255.0
Routed Port :
switch (config)#interface fa 0/1
把 f 0/1 变成路由口。
switch (config-if)#no switch
路由配置:
添加一条路由。
switch (config)#ip route 目的地址 掩码 下一跳
switch (config)#ip route 210.10.10.0 255.255.255.0 218.8.8.8
配置多生成树协议 :
switch(config)#spanning-tree
switch(config)#spanning-tree mst configuration
switch(config-mst)#name ruijie
switch(config-mst)#revision 1
switch(config-mst)#instance 0 vlan 10,20
switch(config-mst)#instance 1 vlan 30,40
switch(config)#spanning-tree mst 0 priority 4096
switch(config)#spanning-tree mst 1 priority 8192
//设定校订本为 1
//开启生成树协议
//建立多生成树协议
//命名为 ruijie
//建立实例 0
//建立实例 1
//设置优先级为 4096
//设置优先级为 8192
switch(config)#interface vlan 10
switch(config-if)#vrrp 1 ip 192.168.10.1 // 此为 vlan 10 的 IP 地址
switch(config)#interface vlan 20
switch(config-if)#vrrp 1 ip 192.168.20.1 // 此为 vlan 20 的 IP 地址
switch(config)#interface vlan 30
switch(config-if)#vrrp 2 ip 192.168.30.1 // 此为 vlan 30 的 IP 地址 ( 另一三层交换机 )
switch(config)#interface vlan 40
switch(config-if)#vrrp 2 ip 192.168.40.1 // 此为 vlan 40 的 IP 地址 ( 另一三层交换机 )
此配置需在两个三层交换机和二层交换机上进行配置
! 在二层交换机上不用配置 VRRP!
冗余链路
在骨干网设备连接中 ,单一链路的连接很容易实现 ,但一个简单的故障就会造成网络的中
断. 因此在实际网络组建的过程中 ,为了保持网络的稳定性 ,在多台交换机组成的网络环境中
通常都使用一些备份连接 ,以提高网络的健壮性、稳定性 .
,
这里的备份连接也称为备份链路或者冗余链路
成一个环路 ,通过环路可以在一定程度上实现冗余
.
.备份链路之间的交换机经常互相连接
, 形
,但是备份链路也会使网
, 交换机之间的环路将导致网络新
链路的冗余备份能为网络带来健壮性、稳定性和可靠性等好处
络存在环路 ,环路问题是备份链路所面临的最为严重的问题
问题的发生 :
广播风暴
多帧复制
地址表的不稳定
解决方法:
生成树协议避免环路
每个 LAN 都会选择一台设备为指定交换机,通过该设备的端口连接到根,该端口为指
定端口( Designated port )
将交换网络中所有设备的根端口 (RP) 和指定端口( DP)设为转发状态( Forwarding ),
将其他端口设为阻塞状态( Blocking )
生成树经过一段时间(默认值是
50 秒左右)稳定之后,所有端口要么进入转发状态,
要么进入阻塞状态。
IEEE 802.1w —快速生成树协议
快速生成树协议概述
快速生成树协议 RSTP(Rapid Spannning Tree Protocol) IEEE 802.1w
RSTP 协议在 STP 协议基础上做了改进,使得收敛速度快得多(最快
生成树协议的配置
开启生成树协议
Switch(config)#Spanning-tree
关闭生成树协议
1 秒以内)
Switch(config)#no Spanning-tree
配置生成树协议的类型
Switch(config)#Spanning-tree mode stp/rstp
锐捷全系列交换机默认使用 MSTP 协议
配置交换机优先级
Switch(config)#spanning-tree priority <0-61440>
(“ 0”或“ 4096”的倍数、共 16 个、缺省 32768)
恢复到缺省值
Switch(config)# no
配置交换机端口的优先级
spanning-tree priority
Switch(config)#interface interface-type interface-number
Switch(config-if)#spanning-tree port-priority number
显示生成树状态
Switch#show spanning-tree
显示端口生成树协议的状态
Switch#show spanning-tree interface fastethernet <0-2/1-24>
生成树协议概述
生成树协议( spanning-tree protocol )由 IEEE 802.1d 标准定义
生成树协议的作用是为了提供冗余链路,解决网络环路问题
生成树协议通过 SPA(生成树算法) 生成一个没有环路的网络, 当主要链路出现故障时,
能够自动切换到备份链路,保证网络的正常通信
配置模式:
全局配置模式 switch(config)#
配置交换机的整体参数
接口配置模式 switch(config-if)#
配置交换机的接口参数
进入全局配置模式
Switch #c onfigure terminal
Switch(config)#exit
Switch#
进入接口配置模式
Switch(config)#interface fastethernet 0/1
Switch(config-if)#exit
Switch(config)#
从子模式下直接返回特权模式
Switch(config-if)#end
Switch#
命令行其他功能
获得帮助
switch#?
switch#show ?
命令简写
全写: switch# configure terminal
简写: Switch# config
使用历史命令
Switch# ( 向上键 )
Switch# ( 向下键 )
配置交换机 Telnet 功能
配置远程登陆密码
Switch(config)#enable secret level 1 0 ruijie
配置进入特权模式密码
Switch (config)#enable secret level 15 0 ruijie
为交换机配置管理 IP
Switch (config)#interface vlan 1
Switch (config-if)#no shutdown
Switch (config-if)#ip address 192.168.1.1 255.255.255.0
Switch (config-if)#end
配置文件的管理
保存配置
将当前运行的参数保存到 flash 中用于系统初始化时初始化参数
Switch#copy running-config startup-config
Switch#write memory
Switch#write
删除配置
永久性的删除 flash 中不需要的文件
使用命令 delete flash:config.text
删除当前的配置: 在配置命令前加 no
例: switch(config-if)# no ip address
查看配置文件内容
Switch#show configure 查看保存在 FLASH 里的配置信息
Switch#show running-config 查看 RAM 里当前生效的配置
配置 Port VLAN
创建 VLAN10 ,将它命名为 test 的例子
Switch# configure terminal
Switch(config)# vlan 10
Switch(config-vlan)# name test
Switch(config-vlan)# end
把接口 0/10 加入 VLAN10
Switch# configure terminal
Switch(config)# interface fastethernet 0/10
Switch(config-if)# switchport mode access
Switch(config-if)# switchport access vlan 10
Switch(config-if)# end
将一组接口加入某一个 VLAN
Switch(config)#interface range fastethernet 0/1-8 , 0/15, 0/20
Switch(config-if-range)# switchport access vlan 20
注:连续接口 0/1-8 ,不连续接口用逗号隔开,但一定要写明模块编号
配置 Tag VLAN-Trunk
把 Fa0/1 配成 Trunk 口
Switch# configure terminal
Switch(config)# interface fastethernet0/1
Switch(config-if)# switchport mode trunk
把端口 Fa0/20 配置为 Trunk 端口,但是不包含 VLAN 2 :
Switch(config)# interface fastethernet 0/20
Switch(config-if)# switchport trunk allowed vlan remove 2
Switch(config-if)# end
Native VLAN
配置命令:
Switch(config-if)# switchport trunk native vlan 20
Switch(config-if)# end
注意:
每个 Trunk 口的缺省 native VLAN 是 VLAN 1
在配置 Trunk 链路时,请确保连接链路两端的 Trunk 口属于相同的 native VLAN
保存 /清除 VLAN 信息
将 VLAN 信息保存到 flash 中
Switch#write memory
从 flash 中只清除 VLAN 信息
Switch#delete flash:vlan.dat
从 RAM 中删除 VLAN
Switch(config)#no vlan VLAN-id
生成树协议的配置
开启生成树协议
Switch(config)#Spanning-tree
关闭生成树协议
Switch(config)#no Spanning-tree
配置生成树协议的类型
Switch(config)#Spanning-tree mode stp/rstp
锐捷全系列交换机默认使用 MSTP 协议
配置交换机优先级
Switch(config)#spanning-tree priority <0-61440>
(“ 0”或“ 4096”的倍数、共 16 个、缺省 32768)
恢复到缺省值
Switch(config)# no spanning-tree priority
配置交换机端口的优先级
Switch(config)#interface interface-type interface-number
Switch(config-if)#spanning-tree port-priority number
配置 STP、 RSTP
Spanning Tree 的缺省配置:
关闭 STP
STP Priority 是 32768
STP port Priority 是 128
STP port cost 根据端口速率自动判断
Hello Time 2 秒
Forward-delay Time 15 秒
Max-age Time 20 秒
可通过 spanning-tree reset 命令让 spanning tree 参数恢复到缺省配置
查看生成树协议配置
显示生成树状态
Switch#show spanning-tree
显示端口生成树协议的状态
Switch#show spanning-tree interface fastethernet <0-2/1-24>
配置 aggregate port
将该接口加入一个 AP
Switch #c onfigure terminal
Switch(config) # interface interface-type interface-id
Switch(config-if-range)#port-group port-group-number
如果这个 AP 不存在,可自动创建 AG 端口
查看聚合端口的汇总信息
Switch#show aggregateport summary
查看聚合端口的流量平衡方式
Switch#show aggregateport load-balance
路由器上配置 telnet
第一步 : 配置端口地址
RouterA# configure terminal !进入全局配置模式
RouterA(config)# interface fastethernet 1/0
!进入路由器接口配置模式
RouterA(config-if)# ip address 192.168.0.1 255.255.255.0
!配置路由器管理接口 IP 地址
RouterA(config-if)# no shutdown !开启路由器 f 1/0 接口
第二步:配置远程登录密码
RouterA(config)# line vty 0 4 !进入路由器线路配置模式
RouterA(config-line)# login !配置远程登录
RouterA(config-line)# password star !设置路由器远程登录密码为
“ star”
RouterA(config-line)#end
第三步:配置路由器特权模式密码
RouterA(config)# enable secret star !设置路由器特权模式密码为
“ star”
或者
RouterA(config)# enable password star
查看配置文件
show version !查看版本及引导信息
show running-config !查看运行配置
show startup-config !查看用户保存在 NVRAM 中的配置文件
保存配置文件
Router#copy running-config startup-config
Router#write memory
Router#write
删除配置文件
Router#delete flash:config.text !删除初始配置文件
查看路由信息
router#show ip route
Codes: C - connected ,S static, R RIP , O- OSPF
IA - OSPF inter area , E1-OSPF external type 1
E2 - OSPF external type 2 , * - candidate default
Gateway of last resort is 10.5.5.5 to network 0.0.0.0
172.16.0.0/24 is subnetted, 1 subnets
C 172.16.11.0 is directly connected, serial1/2
O E2 172.22.0.0/16 [110/20] via 10.3.3.3, 01:03:01, Serial1/2
S* 0.0.0.0/0 [1/0] via 10.5.5.5
静态路由配置命令
配置静态路由用命令 ip route
router(config)#ip route [ 网络编号 ] [ 子网掩码 ] [ 转发路由器的 IP 地址 /本地接口 ]
例: ip route 192.168.10.0 255.255.255.0 serial 1/2
例: ip route 192.168.10.0 255.255.255.0 172.16.2.1
静态路由描述转发路径的方式有两种
指向本地接口(即从本地某接口发出)
指向下一跳路由器直连接口的
IP 地址(即将数据包交给 X.X.X.X )
配置默认路由:
router(config)#ip route 0.0.0.0 0.0.0.0 [ 转发路由器的 IP 地址 /本地接口 ]
RIP 路由协议的版本
RIPv1
有类路由协议,不支持 VLSM
以广播的形式发送更新报文
不支持认证
RIPv2
无类路由协议,支持 VLSM
以组播的形式发送更新报文
支持明文和 MD5 的认证
配置 RIP 协议
配置步骤
1、开启 RIP 路由协议进程
Router(config)#router rip
2、申请本路由器参与 RIP 协议的直连网段信息
Router(config-router)#network 192.168.1.0
3、指定 RIP 协议的版本 2(默认是 version1)
Router(config-router)#version 2
4、在 RIPv2 版本中关闭自动汇总
Router(config-router)#no auto-summary
查看 RIP 配置信息
验证 RIP 的配置
Router#show ip protocols
显示路由表的信息
Router#show ip route
清除 IP 路由表的信息
Router#clear ip route
在控制台显示 RIP 的工作状态
Router#debug ip rip
OSPF 协议
OSPF 配置如下:
1、创建 loopback 接口,定义 ROUTE ID
routerA(config)#interface loopback 10
routerA(config)#ip address 192.168.100.1 255.255.255.0
2、开启 OSPF 进程
routerA(config)#router ospf 10
10 代表进程编号,只具有本地意义
3、申请直连网段
routerA(config-router)#network 10.1.1.0 0.0.0.255 area 0
注意反掩码和区域号
查看 OSPF 配置信息
验证 OSPF 的配置
Router#show ip ospf
显示路由表的信息
Router#show ip route
清除 IP 路由表的信息
Router#clear ip route
在控制台显示 OSPF 的工作状态
Router#debug ip ospf
三层交换的路由功能
三层交换机默认开启路由功能
Switch(config)#ip routing ( 开启三层交换机路由功能 )
三层交换机配置路由接口的两种方法
开启三层交换机物理接口的路由功能
Switch(config)#interface fastethernet 0/5
Switch(config-if)#no switchport
Switch(config-if)#ip address 192.168.1.1 255.255.255.0
Switch(config-if)#no shutdown
关闭物理接口路由功能
Switch(config-if)# switchport
采用 SVI 方式( switch virtual interface )
Switch(config)#interface vlan 10
Switch(config-if)#ip address 192.168.1.1.255 255.255.0
Switch(config-if)#no shutdown
三层交换机和路由器相连的网络
方法一 (SVI) :
Switch(config)#interface f0/10
Switch(config-if)#switchport access vlan 10
Switch(config-if)#exit
Switch(config)#interface vlan 10 switch(config-if)#ip address 192.168.10.1 255.255.255.0
Switch(config-if)#no shutdown
方法二 (路由接口 ):
Switch(config)#interface f0/10
Switch(config-if)#no switchport
Switch(config-if)#ip address 192.168.10.1 255.255.255.0
Switch(config-if)#no shutdown
三层交换机路由协议的配置
静态路由
Switch(config)#ip route x.x.x.x x.x.x.x [x.x.x.x/interface]
RIP
Switch(config)#router rip
Switch(config-router)#network X.X.X.X
Switch(config-router)#version 2
注:三层交换机不支持 no auto-summary
OSPF
Switch(config)#router ospf
Switch(config)#network X.X.X.X X.X.X.X area x
查看三层交换机路由配置
查看路由接口信息
Switch#show ip interface