Packet Tracer配置CHAP双向认证

最新推荐文章于 2024-05-18 16:23:13 发布

傻傻的心动

最新推荐文章于 2024-05-18 16:23:13 发布

阅读量519

点赞数 1

分类专栏： CCNA4 思科实验文章标签：网络运维服务器

Panta rhei

本文链接：https://blog.csdn.net/m0_63624418/article/details/129245914

版权

思科实验同时被 2 个专栏收录

130 篇文章 69 订阅

订阅专栏

CCNA4

29 篇文章 2 订阅

订阅专栏

Packet Tracer配置CHAP双向认证

【拓扑图】

【设备参数表】

设备	接口	IP地址	子网掩码	默认网关
R1	S0/0/0	192.168.12.1	255.255.255.0	N/A
R2	S0/0/0	192.168.12.2	255.255.255.0	N/A

【实验步骤】

Router>en

Router#conf

Configuring from terminal, memory, or network [terminal]?

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#hostname R1

R1(config)#username R2 password cisco

R1(config)#INTerface s0/0/0

R1(config-if)#ip address 192.168.12.1 255.255.255.0

R1(config-if)#no shutdown

%LINK-5-CHANGED: Interface Serial0/0/0, changed state to down

R1(config-if)#

%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to down

R1(config-if)#encapsulation ppp

R1(config-if)#ppp authentication chap

R1(config-if)#exit

R1(config)#

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up

R1(config)#end

R1#

%SYS-5-CONFIG_I: Configured from console by console

R1#show ip interface brief

Interface IP-Address OK? Method Status Protocol

GigabitEthernet0/0 unassigned YES unset administratively down down

GigabitEthernet0/1 unassigned YES unset administratively down down

Serial0/0/0 192.168.12.1 YES manual up up

Serial0/0/1 unassigned YES unset administratively down down

Vlan1 unassigned YES unset administratively down down

R1#show run

R1#show running-config

Building configuration...

Current configuration : 816 bytes

version 15.1

no service timestamps log datetime msec

no service timestamps debug datetime msec

no service password-encryption

hostname R1

no ip cef

no ipv6 cef

username R2 password 0 cisco

license udi pid CISCO1941/K9 sn FTX1524NA7G-

spanning-tree mode pvst

interface GigabitEthernet0/0

no ip address

duplex auto

speed auto

shutdown

interface GigabitEthernet0/1

no ip address

duplex auto

speed auto

shutdown

interface Serial0/0/0

ip address 192.168.12.1 255.255.255.0

encapsulation ppp

ppp authentication chap

interface Serial0/0/1

no ip address

clock rate 2000000

shutdown

interface Vlan1

no ip address

shutdown

ip classless

ip flow-export version 9

line con 0

line aux 0

line vty 0 4

end

R1#

Router>enable

Router#conf

Configuring from terminal, memory, or network [terminal]?

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#hostname R2

R2(config)#username R1 password cisco

R2(config)#interface s0/0/0

R2(config-if)#ip address 192.168.12.2 255.255.255.0

R2(config-if)#encapsulation ppp

R2(config-if)#ppp authentication chap

R2(config-if)#no shutdown