配置MPLS的静态LSP

MPLS的静态LSP

1.配置IP地址

[AR1]int g0/0/0

[AR1-GigabitEthernet0/0/0]ip add 12.1.1.1 24

[AR1-LoopBack0]ip add 1.1.1.1 32

[AR2]int g0/0/0

[AR2-GigabitEthernet0/0/0]ip add 12.1.1.2 24

[AR2-GigabitEthernet0/0/0]int g0/0/1

[AR2-GigabitEthernet0/0/1]ip add 23.1.1.1 24

[AR2-GigabitEthernet0/0/1]int lo 0

[AR2-LoopBack0]ip add 2.2.2.2 32

[AR3]int g0/0/0

[AR3-GigabitEthernet0/0/0]ip add 23.1.1.2 24

[AR3-GigabitEthernet0/0/0]int lo 0

[AR3-LoopBack0]ip add 3.3.3.3 32

2.配置OSPF

[AR1]ospf

[AR1-ospf-1]area 0

[AR1-ospf-1-area-0.0.0.0]network 12.1.1.0 0.0.0.255

[AR1-ospf-1-area-0.0.0.0]network 1.1.1.1 0.0.0.0

[AR2-LoopBack0]ospf

[AR2-ospf-1]area 0

[AR2-ospf-1-area-0.0.0.0]network 12.1.1.0 0.0.0.255

[AR2-ospf-1-area-0.0.0.0]network 2.2.2.2 0.0.0.0

[AR2-ospf-1-area-0.0.0.0]network 23.1.1.0 0.0.0.255

[AR3-LoopBack0]ospf

[AR3-ospf-1]area 0

[AR3-ospf-1-area-0.0.0.0]network 23.1.1.0 0.0.0.255

[AR3-ospf-1-area-0.0.0.0]network 3.3.3.3 0.0.0.0

测试一下是否能ping通3.3.3.3

可以看到图中是不能ping通3.3.3.3，因为我们的MPLS的隧道还没有建立。

3.配置MPLS静态LDP

[AR1]mpls lsr-id 1.1.1.1

[AR1]mpls

Info: Mpls starting, please wait... OK!

[AR1]int g0/0/0

[AR1-GigabitEthernet0/0/0]mpls

[AR2]mpls lsr-id 2.2.2.2

Warning: Can't configure lsr-id when MPLS is enabled.

[AR2]mpls

[AR2]int g0/0/0

[AR2-GigabitEthernet0/0/0]mpls

[AR2]int g0/0/1

[AR2-GigabitEthernet0/0/1]mpls

[AR3]mpls lsr-id 3.3.3.3

[AR3]mpls

Info: Mpls starting, please wait... OK!

[AR3-GigabitEthernet0/0/0]mpls

3.配置标签

[AR1]static-lsp ingress 1-3 destination 3.3.3.3 32 nexthop 12.1.1.2 out-label 200 ##建立一个静态的LSP隧道，压入名字为1-3的目的地址为3.3.3.3子网掩码为32位，下一跳为12.1.1.2，出口标签打上200

查看AR1的MPLS的LSP

[AR2]static-lsp transit 1-3 incoming-interface GigabitEthernet 0/0/0 in-label 20

0 nexthop 23.1.1.2 out-label 100 ## 建立一个lsp静态隧道，交换名字为1-3，进入的接口为g0/0/0入标签为200，下一跳为23.1.1.2，出标签为100

查看AR2的MPLS的LSP

[AR3]static-lsp egress 1-3 incoming-interface GigabitEthernet0/0/0 in-label 100 ##建立一个LSP的隧道，弹出名字为1-3，进入的接口为g0/0/0，入标签为100

查看AR3的MPLS的LSP

[AR3]static-lsp ingress 3-1 destination 1.1.1.1 32 nexthop 23.1.1.1 out-label 10

0

[AR2]static-lsp transit 3-1 incoming-interface g0/0/1 in-label 100 nexthop 12.1

.1.1 out-label 200

[AR1]static-lsp egress 3-1 incoming-interface GigabitEthernet 0/0/0 in-label 20

0

查看MPLS隧道

4.测试连通性