eNSP 配置VLAN hybrid

在sw1 sw2上先将对应接口设置为access

[sw1-Ethernet0/0/1]port link-type access 
[sw1-Ethernet0/0/1]port default vlan 2


[sw2-Ethernet0/0/1]port link-type access 
[sw2-Ethernet0/0/1]port default vlan 2

对于各个sw之间配置为truank

[sw1-Ethernet0/0/1]port link-type truank
[sw1-Ethernet0/0/1]port truank allow-pass 2 to 5

对于sw1的e0/0/4口

希望它将vlan3、vlan4、vlan5的标签脱掉

将vlan2打上标签

以区分他们的流量

[sw1-Ethernet0/0/4]port hybrid tagged vlan 2
[sw1-Ethernet0/0/4]port hybrid untagged vlan 3 to 5

对于pc2它可以正常访问到pc4/5/6 也能通过路由器访问到pc1/3

[sw1-Ethernet0/0/2]port hybrid pvid vlan 3
[sw1-Ethernet0/0/2]port hybrid untagged vlan 3 to 5

对于pc4、pc5不能访问pc6

[sw3-Ethernet0/0/1]port hybrid pvid vlan 4
[sw3-Ethernet0/0/1]port hybrid untagged vlan 3 to 4

[sw2-Ethernet0/0/1]port hybrid pvid vlan 4
[sw2-Ethernet0/0/1]port hybrid untagged vlan 3 to 4

对于pc6，不能被pc4、pc5访问

[sw3-Ethernet0/0/2]port hybrid pvid vlan 5
[sw3-Ethernet0/0/2]port hybrid untagged vlan 3 5

来到R1上配置dhcp，物理接口为vlan3、4、5分配ip，子接口为vlan2分配ip

[r1]dhcp enable
Info: The operation may take a few seconds. Please wait for a moment.done.
[r1]int g0/0/0
[r1-GigabitEthernet0/0/0]ip ad 192.168.2.1 24
Aug  7 2022 23:05:41-08:00 r1 %%01IFNET/4/LINK_STATE(l)[0]:The line protocol IP on the interface GigabitEthernet0/0/0 has entered the UP state. 
[r1-GigabitEthernet0/0/0]q
[r1]int g0/0/0.1

[r1-GigabitEthernet0/0/0.1]dot1q termination vid 2
[r1-GigabitEthernet0/0/0.1]ip ad 192.168.1.1 24
Aug  7 2022 23:06:06-08:00 r1 %%01IFNET/4/LINK_STATE(l)[1]:The line protocol IP on the interface GigabitEthernet0/0/0.1 has entered the UP state. 

[r1-GigabitEthernet0/0/0.1]arp broadcast enable 
[r1-GigabitEthernet0/0/0.1]q
[r1]ip pool v2
Info: It's successful to create an IP address pool.
[r1-ip-pool-v2]network 192.168.1.0 ma 24
[r1-ip-pool-v2]gate 192.168.1.1
[r1-ip-pool-v2]dns 8.8.8.8
[r1-ip-pool-v2]q
[r1]ip pool v345
Info: It's successful to create an IP address pool.
[r1-ip-pool-v345]network 192.168.2.0 ma 24
[r1-ip-pool-v345]gate 192.168.2.1 
[r1-ip-pool-v345]dns 8.8.8.8
[r1-ip-pool-v345]q
[r1]int g0/0/0
[r1-GigabitEthernet0/0/0]dhcp select global 
[r1-GigabitEthernet0/0/0]int g0/0/0.1
[r1-GigabitEthernet0/0/0.1]dhcp se g

测试

pc1 访问 pc 2 4 5 6

pc4 pc5 无法访问 pc6