ZYNQ下驱动ADF5355试验成功

前两个集BLOG分别给出了ADF5355接口的VERILOG设计实现以及设置频率的C语言算法，我今天试验了以，试验成功了。

首先很重要的是ADF5355寄存器配置的设置：

可以在这个基础上修改输入以及输入频率类型，其他不要动。驱动代码如下：

 
#include <stdio.h>
#include "platform.h"
#include "xil_printf.h"

#define R00 0X200960
#define R01 0X1
#define R02 0X42
#define R03 0x3

#define R04_1     0X08008B94
#define R04_0     0X10008B94

#define R04_A_LCK 0x28008B94
#define R04_D_LCK 0x30008B84

#define R05 0X800025
#define R06 0X35C0C076
#define R07 0X120000E7
#define R08 0X102D0428
#define R09 0X1110FCC9
#define R10 0XC0193A
#define R11 0X61300B
#define R12 0X1041C


#define Fref_in 40000	 //输入时钟
#define F_pfd   Fref_in  //鉴相频率
#define MODE1    16777216; //第一部分小数分频模数
#define MODE2    130;  //第二部分小数分频模数



#define IO *(unsigned int volatile *) (0x43c00000)
#define RF_EN *(unsigned int volatile *) (0x43c00004)

void WriteToADF5355(unsigned int  BUF) {while( (IO&1)!=0  ) ;IO=BUF;}

void   Write_frequence_AMP(unsigned int  Freq,unsigned int  Amp)  //写频率和幅度
//AMP ==> 0:-4dbm 1:-1dbm 2:2dbm 3:5dbm
{
 float Freq_N,Freq_temp;
 unsigned int  	Freq2VCO,INT,FRAC1,FRAC2; //整数分频，  小数分频1 小数分频2
 unsigned int  R0_temp=0;  //控制INT
 unsigned int  R4_temp=0,MODE2_temp; //改变输出的分频控制字，一共分成7段
 unsigned int  Out_Divider,RF_Divider;//输出分频控制，3位  及对应的分频数
 unsigned int  I_CP=9000;
 unsigned int  I_BLEED_N;
if((53125<=Freq)&&(Freq<106250))   { Out_Divider=6; RF_Divider=64;}  //分频段
if((106250<=Freq)&&(Freq<212500))  { Out_Divider=5; RF_Divider=32;} //
if((212500<=Freq)&&(Freq<425000))  { Out_Divider=4; RF_Divider=16;}  //
if((425000<=Freq)&&(Freq<850000))  { Out_Divider=3; RF_Divider=8; }   //
if((850000<=Freq)&&(Freq<1700000)) { Out_Divider=2; RF_Divider=4; }   //
if((1700000<=Freq)&&(Freq<3400000)){ Out_Divider=1; RF_Divider=2; }  //
if((3400000<=Freq)&&(Freq<6800000)){ Out_Divider=0; RF_Divider=1; }
  Freq_temp=Freq;
  Freq2VCO=(Freq_temp*RF_Divider)*2;//计算出2倍VCO，从B端口输出
  //计算整数分频INT;小数分频1FRAC1;小数分频2FRAC2
  Freq_temp=Freq;
  Freq_N=(Freq_temp*RF_Divider)/F_pfd; //计算出N分频值，带有小数位

  Freq_temp=Freq_N;
  INT=(unsigned int )Freq_temp;//计算出整数分频INT

  I_BLEED_N=I_CP*4/(INT*375); //计算bleed 电流对应的值
  I_BLEED_N=(unsigned int )I_BLEED_N;

  Freq_temp=(Freq_N-INT)*MODE1;
  FRAC1=(unsigned int )Freq_temp;    //计算出小数分频1-FRAC1

  Freq_temp=(Freq_N-INT)*MODE1
  Freq_temp=Freq_temp-FRAC1;
  FRAC2=(unsigned int )Freq_temp*MODE2;

  MODE2_temp=MODE2;
  WriteToADF5355((Out_Divider<<21)|(I_BLEED_N<<13)|(Amp<<4)|0X35000046);//R6
  WriteToADF5355(R04_D_LCK  |  1<<4  );  //R4-计数器复位
  WriteToADF5355(2|(MODE2_temp<<4)|(FRAC2<<18));//R2
  WriteToADF5355(1|(FRAC1<<4));  //R1
  WriteToADF5355(INT<<4);  //R0
  WriteToADF5355(R04_D_LCK);  //R4-计数器启动
	usleep(161);
  WriteToADF5355(0X200000|(INT<<4));
}


void Init_ADF5355(int mux ){
 WriteToADF5355(R12);
 WriteToADF5355(R11);
 WriteToADF5355(R10);
 WriteToADF5355(R09);
 WriteToADF5355(R08);
 WriteToADF5355(R07);
 WriteToADF5355(R06);
 WriteToADF5355(R05);
 if (mux==1)      WriteToADF5355(R04_1);    // muxout = 1
 else if (mux==2) WriteToADF5355(R04_A_LCK); // ANALOG LOCK
 else if (mux==3) WriteToADF5355(R04_D_LCK); //DIGITAL LOCK
 else             WriteToADF5355(R04_0);// muxout = 0
 WriteToADF5355(R03);
 WriteToADF5355(R02);
 WriteToADF5355(R01);
 usleep(200);
 WriteToADF5355(R00);
}

int check_if_adf5355_online(){
int i =10;unsigned int r ;
while(i--){
Init_ADF5355(1);r= IO&2 ;	 if (r==0) return 0;
Init_ADF5355(0);r= IO&2 ;	 if (r!=0) return 0;
}
return 1 ;
}

int main()
{
	int r  ;
    init_platform();
    RF_EN =1;
    print("Hello World\n\r");
    sleep(1);



    r = check_if_adf5355_online();
    if (r==0)while(1);

  Init_ADF5355(3);

  Write_frequence_AMP(1000*60 , 3);

    while(1) ;

    cleanup_platform();
    return 0;
}

已经测试过了，代码很好用。100M以内的频率输出我用示波器看了么有问题，另外用频谱仪看了几个2G的频点，也都OK。

ADF5355的接口VERILOG代码在上两个BLOG里面，没有任何修改。在VIVADO项目下包装成了AXI_LITE外设，之后用上述驱动代码控制。

{{aAxvOXMOIvVUoXMxvoxiowMwWV8xxWTxoxOIOVIUUOvwVOUiIoUvvTMMVMwovWHWX8vOUOvvviTHUToiVwiVxvvMTXIm8VmUTXmOiXmvMW88IivwmHMoiHIoVU8VvmvIWXTvvOvv8xvMovOWooTxUWMm8UmooOTvvwUIoTwvmWUoiTw8VmvoHWwMIUWOixiowiUoiXwiwwMMIiIXHwUmOWUVmXXwV8iHWOTUiwTU8xwOoV8HVmTWZz}}