如何使用parted对齐分区以得到最优性能

来源地址: http://rainbow.chard.org/2013/01/30/how-to-align-partitions-for-best-per...

How to align partitions for best performance using parted

There are two common problems when creating partitions in Linux on big storage arrays. The first is easy, and the warning message from fdisk is a bit of a giveaway:

WARNING: The size of this disk is 8.0 TB (7970004230144 bytes).
DOS partition table format can not be used on drives for volumes
larger than (2199023255040 bytes) for 512-byte sectors. Use parted(1) and GUID
partition table format (GPT).

The answer: use parted. Don’t have it? Install it!

The second problem is this warning from parted:

(parted) mklabel gpt
(parted) mkpart primary 0 100%
Warning: The resulting partition is not properly aligned for best performance.
Ignore/Cancel?

…and no matter what combination of numbers you use, the message just keeps coming back. It’s tempting to ignore it, but don’t.

There are a few posts on the subject, but this one from HP really gets to the guts of the problem.

Here’s a quick step-by-step guide to aligning partitions properly. It’s just an abstraction of the HP post, but hopefully easier to follow. This will work for most arrays (in fact it works for all the arrays that I’ve seen); there are more options in HP’s post, but I’ve included the most common configuration here.

1. Get the alignment parameters for your array (remember to replace sdb with the name of your device as seen by the kernel).

    # cat /sys/block/sdb/queue/optimal_io_size
    1048576
    # cat /sys/block/sdb/queue/minimum_io_size
    262144
    # cat /sys/block/sdb/alignment_offset
    0
    # cat /sys/block/sdb/queue/physical_block_size
    512

2. Add optimal_io_size to alignment_offset and divide the result by physical_block_size. In my case this was (1048576 + 0) / 512 = 2048.
3. This number is the sector at which the partition should start. Your new parted command should look like

    mkpart primary 2048s 100%

The trailing ‘s’ is important: it tells parted that you’re talking about sectors, not bytes or megabytes.

4. If all went well, the partition will have been created with no warnings. You can check the alignment thusly (replacing ’1′ with the partition number if necessary):

    (parted) align-check optimal 1                                           
    1 aligned

As I alluded to before, there are cases where this won’t work: if optimal_io_size is zero, for example, there are other rules to follow. Of course it would be nice if parted could do this—the values are all available as ioctls, after all—but then what would I write about? :)

末尾的最后一条评论更加实用:
Apparently, using % causes parted to automatically align the sectors for best performance:

(parted) mkpart primary ext4 0% 100%
评论
添加红包

请填写红包祝福语或标题

红包个数最小为10个

红包金额最低5元

当前余额3.43前往充值 >
需支付:10.00
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明:

1.余额是钱包充值的虚拟货币,按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载,可以购买VIP、付费专栏及课程。

余额充值