Blinker利用RGB做氛围灯

RGB为三色灯珠，颜色为红，蓝，绿；
接线 所有灯阴极

接GED,蓝接GPIO15
绿接GPIO13
红接GPIO12

支持语音（变色、亮度调节，开关灯）
色温还有模式代码暂时不加，用不上，
如果装灯带可以使用MOS管作为驱动；
后期慢慢更多骚操作；
可以关注抖音 雨天实验室
学习交流群467948028

#define BLINKER_WIFI
	
#define BLINKER_MIOT_LIGHT
	
#define BLINKER_PRINT Serial
	
 
	
#include <Blinker.h>
	
uint8_t colorR=255, colorG=255, colorB=255, colorW=50;//默认亮度为50，防止亮瞎眼睛
	
char auth[] = "";//你的密钥
	
char ssid[] = "你的wifi名";
	
char pswd[] = "你的wifi密码";
	
// 新建组件对象
	
BlinkerButton Button1("yu");//一路继电器的键值
	
void miotColor(int32_t color)
	
{
	
    BLINKER_LOG("need set color: ", color);
	
 
	
    colorR = color >> 16 & 0xFF;
	
    colorG = color >>  8 & 0xFF;
	
    colorB = color       & 0xFF;
	
 
	
    BLINKER_LOG("colorR: ", colorR, ", colorG: ", colorG, ", colorB: ", colorB);
	
     analogWrite(15, colorB*colorW*0.041);//colorw为亮度值，colorB为蓝灯数值（0-255）esp8266的pwm为0-1024，换算一下公式
	
    analogWrite(13, colorG*colorW*0.041);
	
    analogWrite(12, colorR*colorW*0.041);
	
    BlinkerMIOT.color(color);
	
    BlinkerMIOT.print();
	
}
	
void miotBright(const String & bright)
	
{
	
    BLINKER_LOG("need set brightness: ", bright);
	
 
	
    colorW = bright.toInt();
	
 
	
    BLINKER_LOG("now set brightness: ", colorW);
	
    
	
    analogWrite(15,colorB*colorW*0.041);//在之前的变色调节亮度
	
    analogWrite(13, colorG*colorW*0.041);
	
    analogWrite(12, colorR*colorW*0.041);
	
    BlinkerMIOT.brightness(colorW);
	
    BlinkerMIOT.print();
	
}
	
 
	
 
	
 
	
 
	
 
	
 
	
 
	
 
	
 
	
void miotPowerState(const String & state)
	
{
	
    BLINKER_LOG("need set power state: ", state);
	
 
	
    if (state == BLINKER_CMD_ON) {
	
     analogWrite(15,512);//开机亮度为三色50
	
    analogWrite(13, 512);
	
    analogWrite(12,512);
	
         
	
        BlinkerMIOT.powerState("on");
	
        BlinkerMIOT.print();
	
    }
	
    else if (state == BLINKER_CMD_OFF) {
	
        analogWrite(15,0);
	
    analogWrite(13, 0);
	
    analogWrite(12,0);
	
        BlinkerMIOT.powerState("off");
	
        BlinkerMIOT.print();
	
    }
	
}
	
// 按下按键即会执行该函数
	
void button1_callback(const String & state) {
	
    BLINKER_LOG("get button state: ", state);
	
    digitalWrite(2, !digitalRead(2));
	
}//继电器接口为2，要不要无所谓
	
 
	
// 如果未绑定的组件被触发，则会执行其中内容
	
void dataRead(const String & data)
	
{
	
    BLINKER_LOG("Blinker readString: ", data);
	
}
	
 
	
void setup() {
	
    // 初始化串口
	
    Serial.begin(115200);
	
 
	
    #if defined(BLINKER_PRINT)
	
        BLINKER_DEBUG.stream(BLINKER_PRINT);
	
    #endif
	
 
	
    // 初始化有LED的IO
	
    pinMode(2, OUTPUT);
	
    digitalWrite(2, HIGH);
	
    // 初始化blinker
	
    Blinker.begin(auth, ssid, pswd);
	
    Blinker.attachData(dataRead);
	
    Button1.attach(button1_callback);
	
    BlinkerMIOT.attachPowerState(miotPowerState);
	
   BlinkerMIOT.attachColor(miotColor);
	
   BlinkerMIOT.attachBrightness(miotBright);
	
}
	
 
	
void loop() {
	
    Blinker.run();
	
}