rk3399 usbwifi 调试命令

手动加载WiFi驱动

    加载驱动
        insmod /system/8812au.v2.ko
    启动wlan0
        busybox ifconfig wlan0 up 
    禁用wlan0
        busybox ifconfig wlan0 down
    卸载驱动
        rmmod 8812au

wifi节点加载

    启动wlan0之前可以先使用ifconfig -a wlan0查看wlan0 节点是否存在，
        127|rk3399_mid:/ # ifconfig -a wlan0                                           
            wlan0     Link encap:Ethernet  HWaddr d4:b7:61:9f:3a:3c
                      UP BROADCAST MULTICAST  MTU:1500  Metric:1
                      RX packets:0 errors:0 dropped:0 overruns:0 frame:0 
                      TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 
                      collisions:0 txqueuelen:1000 
                      RX bytes:0 TX bytes:0 
    若不存在，则需先启动p2p_supp_rtl服务创建wlan0节点
        开启p2p_supp_rtl服务
            setprop ctl.start p2p_supp_rtl 
        关闭p2p_supp_rtl服务
            setprop ctl.stop p2p_supp_rtl
        p2p_supp_rtl服务不支持命令开启
    usbwifi开启后连接网络，需要wpa_supplicant服务支持
        开启wpa_supplicant服务
            setprop ctl.start wpa_supplicant
        关闭wpa_supplicant服务
            setprop ctl.stop wpa_supplicant
        wpa_supplicant服务可以使用命令开启
            查找wpa_supplicant服务
                service wpa_supplicant /system/bin/wpa_supplicant 
                    -iwlan0 -Dnl80211 -c/data/misc/wifi/wpa_supplicant.conf \
                    -I/system/etc/wifi/wpa_supplicant_overlay.conf \
                    -e/data/misc/wifi/entropy.bin -O/data/misc/wifi/sockets \
                    -g@android:wpa_wlan0
            输入命令开启wpa_supplicant服务
                /system/bin/wpa_supplicant  -iwlan0 -Dnl80211 -c/data/misc/wifi/wpa_supplicant.conf  -I/system/etc/wifi/wpa_supplicant_overlay.conf  -e/data/misc/wifi/entropy.bin -O/data/misc/wifi/sockets   -g@android:wpa_wlan0 -dd
                -dd  使用logcat查看时打开与wpa_supplicant运行时输出的log
                例如：
                    logcat -c
                    ./wpa_supplicant
                    logcat    只查看与wpa_supplicant运行时的log

iw命令简单使用

    扫描wifi并打印出扫描到wifi的SSID
        iw dev wlan0 scan |grep "SSID:" -i   
    连接wifi xmzw
        iw wlan0 connect xmzw

wpa_cli命令使用

    打开debuglog
        wpa_cli -iwlan0 -p/data/misc/wifi/sockets log_level debug
    扫描AP
        wpa_cli -iwlan0 scan
    显示扫描结果
        wpa_cli -iwlan0 scan_result
            例：rk3399_mid:/ # wpa_cli -iwlan0 scan       
                OK
                rk3399_mid:/ # wpa_cli -iwlan0 scan_results                 
                bssid / frequency / signal level / flags / ssid
                10:7b:44:79:46:b4       5745    -61     [WPA-PSK-CCMP+TKIP][WPA2-PSK-CCMP+TKIP][ESS]    A5
                70:62:b8:84:a0:90       2417    -61     [WPA-PSK-CCMP][WPA2-PSK-CCMP][WPS][ESS] D-Link_DIR-612
                10:7b:44:c0:de:82       2437    -48     [WPA2-PSK-CCMP][ESS]    dd-wrt_2.4G
                f0:92:b4:76:84:19       2412    -55     [WPA-PSK-CCMP+TKIP][WPA2-PSK-CCMP+TKIP][ESS]    ChinaNet-Jamg
                b0:95:8e:b8:64:13       2462    -57     [WPA-PSK-CCMP][WPA2-PSK-CCMP][ESS]      TP-LINK blue
                f0:92:b4:76:aa:51       2412    -54     [WPA-PSK-CCMP+TKIP][WPA2-PSK-CCMP+TKIP][ESS]    ChinaNet-GSsw
                20:76:93:3a:b0:70       2437    -64     [WPA2-PSK-CCMP][ESS]    newifi_2.4G_test
                70:af:6a:48:a2:73       2437    -65     [WPA-PSK-CCMP][WPA2-PSK-CCMP][ESS]      cpf
                ec:88:8f:75:3f:e2       2437    -66     [WPA-PSK-CCMP+TKIP][WPS][ESS]   db4iot
                14:75:90:79:89:0f       2462    -66     [WPA-PSK-CCMP][WPA2-PSK-CCMP][WPS][ESS] CP_2.4G
                88:70:22:00:6e:c4       2452    -67     [WPA2-PSK-CCMP][ESS]    OrayBox-6-yanfa
                24:05:0f:79:48:da       2437    -72     [WPA-PSK-CCMP][WPA2-PSK-CCMP][ESS]      cccc
                20:76:93:3a:b0:72       5745    -67     [WPA2-PSK-CCMP][ESS]    newifi_5G_test
                00:24:d2:c6:74:b7       2412    -66     [WPA-PSK-CCMP+TKIP][WPA2-PSK-CCMP+TKIP][ESS]    WWW
                00:26:75:01:ba:09       2412    -78     [WPA2-PSK-CCMP][ESS]    LBWiFi410
                b0:39:56:66:a2:b3       2412    -67     [WPA2-PSK-CCMP][WPS][ESS]       weimob--sz
                54:e0:61:21:42:d9       2447    -71     [WPA-PSK-CCMP+TKIP][WPA2-PSK-CCMP+TKIP][WPS][ESS]       ChinaNet-dEPG
                cc:08:fb:7e:6c:0d       2462    -76     [WPA-PSK-CCMP][WPA2-PSK-CCMP][ESS]      TP-LINK_6C0D
                10:7b:44:c0:de:84       5180    -79     [WPA2-PSK-CCMP][ESS]    dd-wrt_5G
    列出当前联网状态：
        rk3399_mid:/ # wpa_cli -iwlan0 status                                          
            bssid=10:7b:44:c0:de:84
            freq=5180
            ssid=dd-wrt_5G
            id=1
            id_str=%7B%22creatorUid%22%3A%221000%22%2C%22configKey%22%3A%22%5C%22dd-wrt_5G%5C%22WPA_PSK%22%7D
            mode=station
            pairwise_cipher=CCMP
            group_cipher=CCMP
            key_mgmt=WPA2-PSK
            wpa_state=COMPLETED
            ip_address=192.168.50.117
            p2p_device_address=d6:b7:61:9f:3a:3c
            address=d4:b7:61:9f:3a:3c
            uuid=6f47db9a-277a-56db-b7bf-dc203c2a9905
    列出所有备选网络
        rk3399_mid:/ # wpa_cli -iwlan0 list_networks                                 
            network id / ssid / bssid / flags
            0       dd-wrt_2.4G     any     [DISABLED][TEMP-DISABLED]
            1       dd-wrt_5G       any     [CURRENT]
    增加一个备选网络
        rk3399_mid:/ # wpa_cli -iwlan0 add_network
            2
    设置要连接的网络名称
        rk3399_mid:/ # wpa_cli -iwlan0 set_network 2 ssid '"dd-wrt_5G"'                
            OK
    设置要连接网络的密码
        rk3399_mid:/ # wpa_cli -iwlan0 set_network 2 psk '"12341234"'
            OK
    启用网络，当扫描到启用网络是会自动连接
        rk3399_mid:/ # wpa_cli -iwlan0 enable_network 2
            OK
    禁用网络
        rk3399_mid:/ # wpa_cli -iwlan0 disable_network 2                             
            OK
    保存配置：
        rk3399_mid:/ # wpa_cli -iwlan0 save_config
            OK