高通平台手机开发之Modem

最新推荐文章于 2024-09-23 17:24:41 发布

司马如风

最新推荐文章于 2024-09-23 17:24:41 发布

阅读量1.8k

点赞数 3

分类专栏： Modem

Modem 专栏收录该内容

33 篇文章 46 订阅

订阅专栏

高通平台手机开发之Modem

1、检查原理图，把每个频段的发送，接收通道都整理清楚形成表格。

a) 一般每个频段有一个发送通路，两个接受通路（4G要求的），主天线通路和分集天线通路。rx0, rx1, tx0，主天线通路默认是rx0。

b) 有的频段没有分集天线通路，如tdscmda B34

c) 有的接收回路几个频段共用一条线：G900/B8, G850/B5, G1900/B2, G1800/B3, B1/B4,B38/B41

2、在rf_card的配置里找，看有没有和我们硬件配置相似的，比如modem_proc/rfc_dime/rf_card/rfc_wtr1625_apac，如果没有相似的，就重新建一个rf_card配置文件：modem_proc/rfc_dime/rf_card/rfc_wtr1625_bacon。整体复制rfc_wtr1625_apac，然后改名，然后把里面的宏，函数名都改成wtr1625_bacon。

改动编译文件scons

在文件modem_proc/rfc_dime/build/modem_rfc_dime.scons里加入include目录

env.PublishProtectedApi('RFC_RF_CARD_INC', [

'${RFC_ROOT}/rf_card/rfc_wtr1625_vz_sv2/common/inc',

'${RFC_ROOT}/rf_card/rfc_wtr1625_bacon/common/inc'

])

编译软件，看看编译是否通过？编译通过后，进行下一步。

3、加入新的开关器件

a) 在modem_proc/rfdevice_asm/src目录下，复制一个类似的器件，然后改动。

修改modem_proc/rfdevice_asm/src/rfcdevice_asm_factory_ag.cpp，并增加新的ASM驱动

else if ( mfg_id == 0x01A5 && prd_id == 0x5F && prd_rev == 0)

{

asm_data =rfdevice_asm_sky13488_data_ag::get_instance();

}

编译通过后，进行下一步。

4、加入新的PA器件

a) 在目录modem_proc/rfdevice_pa/src，复制一个类似的器件，然后改动。

修改modem_proc/rfdevice_pa/src/rfdevice_pa_factory_ag.cpp，并增加新的PA驱动

else if ( mfg_id == 0x134 && prd_id == 0x30 && prd_rev == 0)

{

pa_data =rfdevice_pa_rfmd_7459_data_ag::get_instance();

}

编译通过后，进行下一步。

5、在rf_card里加上器件，ASM，PA等MIPI接口的器件。这些器件在modem软件启动时会扫描的。

如果用了不是MIPI接口的器件，不用在这里加

modem_proc/rfc_dime/rf_card/rfc_wtr1625_bacon/common/src/rfc_wtr1625_bacon_cmn_ag.cpp

rfc_device_cfg_info_typerfc_wtr1625_bacon_cmn_devices_list[] =

{

{ /*Device: WTR1625 */

RFDEVICE_TRANSCEIVER, /* DEVICE_TYPE */

WTR1625, /* DEVICE_NAME */

0, /* DEVICE_TYPE_INSTANCE */

RFDEVICE_COMM_PROTO_SSBI, /*DEVICE_COMM_PROTOCOL */

{ RFC_DEVICE_COMM_BUS_SSBI_1,RFC_DEVICE_COMM_BUS_SSBI_2,},/* DEVICE_COMM_BUS */

0 /*Warning: Not specified*/,/* MANUFACTURER_ID */

0 /*Warning: Not specified*/, /* PRODUCT_ID */

0 /*Warning: Not specified*/,/* PRODUCT_REV */

0 /*Warning: Not specified*/,/* DEFAULT USID RANGE START */

0 /*Warning: Not specified*/,/* DEFAULT USID RANGE END */

0 /*Warning: Not specified*/,/* ASSIGNED_USID */

0 /*Warning: Not specified*/,/* RFFE_GROUP_ID */

FALSE, /* INIT */

RFC_TX_MODEM_CHAIN_0, /*ASSOCIATED_DAC */

RFDEVICE_TYPE_INVALID, /*ASSOCIATED_DEVICE_TYPE */

0 /*Warning: Not specified*/,/* ASSOCIATED_DEVICE_TYPE_INSTANCE */

}, /* END - Device: WTR1625 */

{ /*Device: QFE1101 */ PAPower Manager，用了管理PA的功率，可以减少电流消耗。发射通道需要

RFDEVICE_PAPM, /* DEVICE_TYPE */

QFE1101, /* DEVICE_NAME */

0, /* DEVICE_TYPE_INSTANCE */

RFDEVICE_COMM_PROTO_RFFE, /*DEVICE_COMM_PROTOCOL */

{ 0,0 /* 0 not specified */,}, /*DEVICE_COMM_BUS */

0x0217, /* MANUFACTURER_ID */

0x30, /* PRODUCT_ID */

0, /* PRODUCT_REV */

0x4, /* DEFAULT USID RANGESTART */

0x4, /* DEFAULT USID RANGE END */

0x4, /* ASSIGNED_USID */

0x4, /* RFFE_GROUP_ID */

TRUE, /* INIT */

RFC_INVALID_PARAM, /*ASSOCIATED_DAC */

RFDEVICE_TYPE_INVALID, /*ASSOCIATED_DEVICE_TYPE */

0 /*Warning: Not specified*/,/* ASSOCIATED_DEVICE_TYPE_INSTANCE */

}, /* END - Device: QFE1100 */

{ /*Device: QFE1550 */ Antanna Tuner，天线调谐器，接收通道用的

RFDEVICE_TUNER, /* DEVICE_TYPE */

QFE1550, /* DEVICE_NAME */

0, /* DEVICE_TYPE_INSTANCE */

RFDEVICE_COMM_PROTO_RFFE, /*DEVICE_COMM_PROTOCOL */

{ RFC_DEVICE_COMM_BUS_SSBI_1,0 /*0 not specified */,}, /* DEVICE_COMM_BUS */

0x0217, /* MANUFACTURER_ID */

0x02, /* PRODUCT_ID */

0, /* PRODUCT_REV */

0x7, /* DEFAULT USID RANGESTART */

0x7, /* DEFAULT USID RANGE END */

0x7, /* ASSIGNED_USID */

0x7, /* RFFE_GROUP_ID */

FALSE, /* INIT */

RFC_INVALID_PARAM, /*ASSOCIATED_DAC */

RFDEVICE_TYPE_INVALID, /*ASSOCIATED_DEVICE_TYPE */

0 /*Warning: Not specified*/,/* ASSOCIATED_DEVICE_TYPE_INSTANCE */

}, /* END - Device: QFE1550 */

{ /*Device: RFMD1500 */ 开关器件

RFDEVICE_ASM, /* DEVICE_TYPE */

GEN_ASM /* ASM_16T */, /* DEVICE_NAME */

0, /* DEVICE_TYPE_INSTANCE */

RFDEVICE_COMM_PROTO_RFFE, /*DEVICE_COMM_PROTOCOL */

{ RFC_DEVICE_COMM_BUS_SSBI_1,0 /*0 not specified */,}, /* DEVICE_COMM_BUS */

0x0134, /* MANUFACTURER_ID */

0x5D, /* PRODUCT_ID */

0, /* PRODUCT_REV */

0xB, /* DEFAULT USID RANGESTART */

0xB, /* DEFAULT USID RANGE END */

0xB, /* ASSIGNED_USID */

0xB, /* RFFE_GROUP_ID */

FALSE, /* INIT */

RFC_INVALID_PARAM, /*ASSOCIATED_DAC */

RFDEVICE_TYPE_INVALID, /*ASSOCIATED_DEVICE_TYPE */

0 /*Warning: Not specified*/,/* ASSOCIATED_DEVICE_TYPE_INSTANCE */

}, /* END - Device: ASM_16T */

{ /*Device: RFMD1660 */ 开关器件

RFDEVICE_ASM, /* DEVICE_TYPE */

GEN_ASM /* ASM_10T */, /* DEVICE_NAME */

1, /* DEVICE_TYPE_INSTANCE */

RFDEVICE_COMM_PROTO_RFFE, /*DEVICE_COMM_PROTOCOL */

{ RFC_DEVICE_COMM_BUS_SSBI_1,0/* 0 not specified */,}, /* DEVICE_COMM_BUS */

0x0134, /* MANUFACTURER_ID */

0x78, /* PRODUCT_ID */

0, /* PRODUCT_REV */

0xA, /* DEFAULT USID RANGESTART */

0xA, /* DEFAULT USID RANGE END*/

0xA, /* ASSIGNED_USID */

0xA, /* RFFE_GROUP_ID */

FALSE, /* INIT */

RFC_INVALID_PARAM, /*ASSOCIATED_DAC */

RFDEVICE_TYPE_INVALID, /*ASSOCIATED_DEVICE_TYPE */

0 /*Warning: Not specified*/,/* ASSOCIATED_DEVICE_TYPE_INSTANCE */

}, /* END - Device: ASM_10T */

{ /*Device: HCPA,RF7459, Same asRF7389 */

RFDEVICE_PA, /* DEVICE_TYPE */ PA器件

GEN_PA /* HCPA */, /*DEVICE_NAME */

0, /* DEVICE_TYPE_INSTANCE */

RFDEVICE_COMM_PROTO_RFFE, /*DEVICE_COMM_PROTOCOL */

{ 0,0 /* 0 not specified */,},/* DEVICE_COMM_BUS */

0x0134, /* MANUFACTURER_ID */

0x30,

0, /* PRODUCT_REV */

0xF, /* DEFAULT USID RANGESTART */

0xF, /* DEFAULT USID RANGE END*/

0xF, /* ASSIGNED_USID */

0xF, /* RFFE_GROUP_ID */

FALSE, /* INIT */

RFC_INVALID_PARAM, /*ASSOCIATED_DAC */

RFDEVICE_TYPE_INVALID, /*ASSOCIATED_DEVICE_TYPE */

0 /*Warning: Not specified*/,/* ASSOCIATED_DEVICE_TYPE_INSTANCE */

}, /* END - Device: HCPA */

{ /*Device: TRX_HDET */ 这个设备没有具体的硬件器件，它是通过某种电路来实现的，需要在软件里加上它。

RFDEVICE_HDET, /* DEVICE_TYPE */

TRX_HDET, /* DEVICE_NAME */

0, /* DEVICE_TYPE_INSTANCE */

RFDEVICE_COMM_PROTO_SSBI, /*DEVICE_COMM_PROTOCOL */

{ RFC_DEVICE_COMM_BUS_SSBI_1,0 /*0 not specified */,}, /* DEVICE_COMM_BUS */

0 /*Warning: Not specified*/,/* MANUFACTURER_ID */

0 /*Warning: Not specified*/, /* PRODUCT_ID */

0 /*Warning: Not specified*/,/* PRODUCT_REV */

0 /*Warning: Not specified*/,/* DEFAULT USID RANGE START */

0 /*Warning: Not specified*/,/* DEFAULT USID RANGE END */

0 /*Warning: Not specified*/,/* ASSIGNED_USID */

0 /*Warning: Not specified*/,/* RFFE_GROUP_ID */

FALSE, /* INIT */

RFC_INVALID_PARAM, /*ASSOCIATED_DAC */

RFDEVICE_TRANSCEIVER, /*ASSOCIATED_DEVICE_TYPE */

0, /* ASSOCIATED_DEVICE_TYPE_INSTANCE */

}, /* END - Device: TRX_HDET*/

{ /*Device: RFDEVICE_INVALID*/

RFDEVICE_TYPE_INVALID, /* DEVICE_TYPE */

RFDEVICE_INVALID, /* DEVICE_NAME */

0 /*Warning: Not specified*/,/* DEVICE_TYPE_INSTANCE */

RFDEVICE_COMM_PROTO_INVALID,/* DEVICE_COMM_PROTOCOL */

{ 0 /* 0 not specified */,0 /* 0not specified */,}, /* DEVICE_COMM_BUS */

0 /*Warning: Not specified*/,/* MANUFACTURER_ID */

0 /*Warning: Not specified*/, /* PRODUCT_ID */

0 /*Warning: Not specified*/,/* PRODUCT_REV */

0 /*Warning: Not specified*/,/* DEFAULT USID RANGE START */

0 /*Warning: Not specified*/,/* DEFAULT USID RANGE END */

0 /*Warning: Not specified*/,/* ASSIGNED_USID */

0 /*Warning: Not specified*/,/* RFFE_GROUP_ID */

FALSE, /* INIT */

RFC_INVALID_PARAM, /*ASSOCIATED_DAC */

RFDEVICE_TYPE_INVALID, /*ASSOCIATED_DEVICE_TYPE */

0 /*Warning: Not specified*/,/* ASSOCIATED_DEVICE_TYPE_INSTANCE */

}, /* END - Device:RFDEVICE_INVALID */

};

6、根据硬件原理图，来配置每一条软件通路

在目录modem_proc/rfc_dime/rf_card/rfc_wtr1625_bacon下，/gsm, /lte, /tdscdma, wcdma每一条通道都要配置正确。其中QFE1101的硬件手册里没有发现是如何配置Port的，见附件QFE1101.png，里面有Port表。

7、配置RX通道，rx0,rx1

modem_proc/rfc_dime/rf_card/rfc_wtr1625_bacon/common/src/rfc_wtr1625_bacon_cmn_ag.cpp

rfm_devices_configuration_typerfc_wtr1625_bacon_logical_device_properties =

{

{ /* Mode Concurrencies: Bit0represents Rx concurrency and Bit1 represents Tx concurrency */

{ 0x0, 0x0, 0x0, 0x0, 0x0,0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, },

{ /* device_support */

{ /* Logical Device 0 */ //rx0 通道配置，支持哪些频段

/* bands_supported */

{

/* Bit mask element 0 */

), /* End Bit mask element 0 */

/* Bit mask element 1 */

(

//( (uint64)1 <<(SYS_BAND_WCDMA_I_IMT_2000 - 64) ) | ( (uint64)1 <<(SYS_BAND_WCDMA_II_PCS_1900 - 64) ) | ( (uint64)1 <<(SYS_BAND_WCDMA_IV_1700 - 64) ) | ( (uint64)1 << (SYS_BAND_WCDMA_V_850 -64) ) | ( (uint64)1 << (SYS_BAND_WCDMA_VIII_900 - 64) ) | ( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND1 - 64) ) | ( (uint64)1 <<(SYS_BAND_LTE_EUTRAN_BAND2 - 64) ) | ( (uint64)1 <<(SYS_BAND_LTE_EUTRAN_BAND4 - 64) ) | ( (uint64)1 <<(SYS_BAND_LTE_EUTRAN_BAND5 - 64) ) | ( (uint64)1 << (SYS_BAND_LTE_EUTRAN_BAND8- 64) )

( (uint64)1<< (SYS_BAND_WCDMA_I_IMT_2000 - 64) ) |

( (uint64)1<< (SYS_BAND_WCDMA_II_PCS_1900 - 64) ) |

( (uint64)1<< (SYS_BAND_WCDMA_III_1700 - 64) ) |

( (uint64)1<< (SYS_BAND_WCDMA_IV_1700 - 64) ) |

( (uint64)1<< (SYS_BAND_WCDMA_V_850 - 64) ) |

( (uint64)1<< (SYS_BAND_WCDMA_VIII_900 - 64) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND1 - 64) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND2 - 64) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND3 - 64) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND4 - 64) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND5 - 64) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND7 - 64) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND8 - 64) )

), /* End Bit mask element 1 */

/* Bit mask element 2 */

(

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND20 - 128) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND38 - 128) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND39 - 128) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND40 - 128) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND41 - 128) ) |

( (uint64)1<< (SYS_BAND_TDS_BANDA - 128) ) |

( (uint64)1<< (SYS_BAND_TDS_BANDF - 128) )

), /* End Bit mask element 2 */

/* ca1_bands_supported */

{

/* Bit mask element 0 */

(

), /* End Bit mask element 0 */

/* Bit mask element 1 */

(

), /* End Bit mask element 1 */

/* Bit mask element 2 */

(

), /* End Bit mask element 2 */

( RFM_DEVICE_RX_SUPPORTED |RFM_DEVICE_TX_SUPPORTED),

RFM_DEVICE_1, /* AssociatedSlave Device for RFM_DEVICE_0 */

}, /* End Logical Device 0 */

{ /* Logical Device 1 */ //rx1 通道配置，支持哪些频段

/* bands_supported */

{

/* Bit mask element 0 */

(

), /* End Bit mask element 0 */

/* Bit mask element 1 */

(

( (uint64)1<< (SYS_BAND_WCDMA_I_IMT_2000 - 64) ) |

( (uint64)1<< (SYS_BAND_WCDMA_II_PCS_1900 - 64) ) |

( (uint64)1<< (SYS_BAND_WCDMA_III_1700 - 64) ) |

( (uint64)1<< (SYS_BAND_WCDMA_IV_1700 - 64) ) |

( (uint64)1<< (SYS_BAND_WCDMA_V_850 - 64) ) |

( (uint64)1<< (SYS_BAND_WCDMA_VIII_900 - 64) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND1 - 64) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND2 - 64) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND3 - 64) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND4 - 64) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND5 - 64) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND7 - 64) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND8 - 64) )

), /* End Bit mask element 1 */

/* Bit mask element 2 */

(

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND20 - 128) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND38 - 128) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND39 - 128) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND40 - 128) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND41 - 128) )

), /* End Bit mask element 2 */

/* ca1_bands_supported */

{

/* Bit mask element 0 */

(

), /* End Bit mask element 0 */

/* Bit mask element 1 */

(

), /* End Bit mask element 1 */

/* Bit mask element 2 */

(

), /* End Bit mask element 2 */

( RFM_DEVICE_RX_SUPPORTED),

RFM_INVALID_DEVICE, /*Associated Slave Device for RFM_DEVICE_1 */

}, /* End Logical Device 1 */

8、生成QCN

a) 在目录modem_proc/rftarget_dime/common/qcn，找一个相近的，例如wtr1625_apac，来生成QCN，删除里面不存在的频段，加入有的频段。使之和硬件对应。

b) 根据硬件修改MSM8974_WTR1625_APAC_MASTERFILE.xml里的这些NV项

c) 用QDART来生成QCN

9、调试

a) MIPI器件可以用QDART来做通路测试

b) 连接仪器来做测试，如果不通，通过硬件来量信号，看是什么地方不通。

根据电路配置来说明软件实现

rfc_device_info_typerf_card_wtr1625_bacon_rx0_lte_b1_device_info =

{

0x022902A2, /* Revision: v2.41.674 */

RFC_RX_MODEM_CHAIN_0, /* Modem Chain */

0 /*Warning: Not Specified */, /* ET Modem Chain */

0, /*NV Container */

0 /*Warning: Not Specified */, /* Antenna */

2, /*NUM_DEVICES_TO_CONFIGURE */

{

RFDEVICE_TRANSCEIVER,

WTR1625, /* NAME */

0, /* DEVICE_TYPE_INSTANCE */

0, /* PHY_PATH_NUM */

{

0 /*Warning: Not specified*/, /*INTF_REV */

(int)WTR1625_LTEFDD_PRX_BAND1_PMB4, /*PORT */ W1625上的控制端口，看硬件原理图

( RFDEVICE_PA_LUT_MAPPING_INVALID ), /* RF_ASIC_BAND_PA_LUT_MAP */

FALSE, /* TXAGC_LUT */

0, /* Array Filler */

{

RFDEVICE_ASM,

GEN_ASM /* ASM_16T */, /* NAME */

0, /* DEVICE_TYPE_INSTANCE */

0 /*Warning: Not specified*/, /* PHY_PATH_NUM */

{

0 /* Orig setting: */, /*INTF_REV */

(0x0134 << 22)/*mfg_id*/ | (0x5D<< 14)/*prd_id*/ | (10)/*port_num*/, /* PORT_NUM */ 器件选通通道

0, /* Array Filler */

};

rfc_sig_info_typerf_card_wtr1625_bacon_rx0_lte_b1_sig_cfg =

{

0x022902A2, /* Revision: v2.41.674 */

{

{ (int)RFC_SIG_LIST_END, RFC_LOW }

};

rfc_device_info_typerf_card_wtr1625_bacon_rx1_lte_b1_device_info =

{

0x022902A2, /* Revision: v2.41.674 */

RFC_RX_MODEM_CHAIN_1, /* Modem Chain */

0 /* Warning:Not Specified */, /* ET Modem Chain */

1, /*NV Container */

1 /*Warning: Not Specified */, /* Antenna */

3, /*NUM_DEVICES_TO_CONFIGURE */

{

RFDEVICE_TRANSCEIVER,

WTR1625, /* NAME */

0, /* DEVICE_TYPE_INSTANCE */

1, /* PHY_PATH_NUM */

{

0 /*Warning: Not specified*/, /*INTF_REV */

(int)WTR1625_LTEFDD_DRX_BAND1_DMB1, /*PORT */

( RFDEVICE_PA_LUT_MAPPING_INVALID ), /* RF_ASIC_BAND_PA_LUT_MAP */

FALSE, /* TXAGC_LUT */

0, /* Array Filler */

{

RFDEVICE_ASM,

GEN_ASM /* ASM_10T */, /* NAME */

1, /* DEVICE_TYPE_INSTANCE */

0 /*Warning: Not specified*/, /* PHY_PATH_NUM */

{

0 /* Orig setting: */, /*INTF_REV */

(0x0134 << 22)/*mfg_id*/ | (0x78<< 14)/*prd_id*/ | (8)/*port_num*/, /* PORT_NUM */

0, /* Array Filler */

{

RFDEVICE_TUNER, 从原理图上看，所有的分集天线都通过了Tuner，所以要把这个器件加上

QFE1550, /* NAME */

0, /* DEVICE_TYPE_INSTANCE */

0 /*Warning: Not specified*/, /* PHY_PATH_NUM */

{

0 /* Orig setting: */, /*INTF_REV */

0, /* Array Filler */

};

rfc_sig_info_typerf_card_wtr1625_bacon_rx1_lte_b1_sig_cfg =

{

0x022902A2, /* Revision: v2.41.674 */

{

b1 rx1通过了器件XM0830SJ-DL0612来选通b1或b4，这个器件是通过GPIO120来控制的

{ (int)RFC_WTR1625_BACON_RF_PATH_SEL_05, RFC_HIGH }, /* GPIO_120*/

{ (int)RFC_SIG_LIST_END, RFC_LOW }

};

rfc_device_info_typerf_card_wtr1625_bacon_tx0_lte_b1_device_info =

{

0x022902A2, /* Revision: v2.41.674 */

RFC_TX_MODEM_CHAIN_0, /* Modem Chain */

RFC_TX_MODEM_CHAIN_1, /* ET Modem Chain */

0, /*NV Container */

0 /*Warning: Not Specified */, /* Antenna */

5, /*NUM_DEVICES_TO_CONFIGURE */

{

RFDEVICE_TRANSCEIVER,

WTR1625, /* NAME */

0, /* DEVICE_TYPE_INSTANCE */

0, /* PHY_PATH_NUM */

{

0 /*Warning: Not specified*/, /*INTF_REV */

(int)WTR1625_LTEFDD_TX_BAND1_TMB3, /*PORT */

(RFDEVICE_PA_LUT_MAPPING_VALID | WTR1625_HP_LUT_TYPE <<RFDEVICE_PA_STATE_0_BSHFT | WTR1625_HP_LUT_TYPE <<RFDEVICE_PA_STATE_1_BSHFT | WTR1625_HP_LUT_TYPE <<RFDEVICE_PA_STATE_2_BSHFT | WTR1625_LP_LUT_TYPE <<RFDEVICE_PA_STATE_3_BSHFT ), /* RF_ASIC_BAND_PA_LUT_MAP */ Loop 表之类的，抄的，不需要改的

FALSE, /* TXAGC_LUT */

0, /* Array Filler */

{

RFDEVICE_PA,

GEN_PA, /* NAME */

0, /* DEVICE_TYPE_INSTANCE */

0 /*Warning: Not specified*/, /* PHY_PATH_NUM */

{

0 /* Orig setting: */, /*INTF_REV */

(0x0134 << 22)/*mfg_id*/ | (0x30<< 14)/*prd_id*/ | (22)/*port_num*/, /* PORT_NUM */

0, /* Array Filler */

{ 发射通道需要加上PA Power Manager器件来控制发射功率

RFDEVICE_PAPM,

QFE1101, /* NAME */

0, /* DEVICE_TYPE_INSTANCE */

0 /*Warning: Not specified*/, /* PHY_PATH_NUM */

{

0 /* Orig setting: */, /*INTF_REV */

(0x217 <<22)/*mfg_id*/ | (0x30 << 14)/*prd_id*/ | (9)/*port_num*/, /*PORT_NUM */ 这个没有具体的资料，也是从原来的Code里抄的

0, /* Array Filler */

{

RFDEVICE_ASM,

GEN_ASM /* ASM_16T */, /* NAME */

0, /* DEVICE_TYPE_INSTANCE */

0 /*Warning: Not specified*/, /* PHY_PATH_NUM */

{

0 /* Orig setting: */, /*INTF_REV */

(0x0134 << 22)/*mfg_id*/ | (0x5D<< 14)/*prd_id*/ | (10)/*port_num*/, /* PORT_NUM */

0, /* Array Filler */

{ 没有实际存在的器件对应，可能通过电路来实现，需要加上

RFDEVICE_HDET,

TRX_HDET, /* NAME */

0, /* DEVICE_TYPE_INSTANCE */

0 /*Warning: Not specified*/, /* PHY_PATH_NUM */

{

0 /* Orig setting: */, /*INTF_REV */

0, /* Array Filler */

};

rfc_sig_info_typerf_card_wtr1625_bacon_tx0_lte_b1_sig_cfg =

{

0x022902A2, /* Revision: v2.41.674 */

{

{ (int)RFC_WTR1625_BACON_TX_GTR_TH, RFC_CONFIG_ONLY }, 这两项不加也可以，加在这里是从原有文件里带的

{ (int)RFC_WTR1625_BACON_PA_IND, RFC_CONFIG_ONLY },

{ (int)RFC_SIG_LIST_END, RFC_LOW }

};

{

RFDEVICE_PA,

GEN_PA /* HCPA */, /* NAME */

0, /* DEVICE_TYPE_INSTANCE */

0/*Warning: Not specified*/, /* PHY_PATH_NUM */

{

0 /* Orig setting: */, /* INTF_REV */

(0x01A5 << 22)/*mfg_id*/ | (0x09 << 14)/*prd_id*/ | (13 << 7)/*sec_port_num*/ | (9)/*port_num*/, /* PORT_NUM */ 这个sec_port_num也是从原来code里抄的，应该不需要

0, /* Array Filler */

高通平台手机开发之Modem

2016年02月25日 18:22:49

阅读数：8697

1、检查原理图，把每个频段的发送，接收通道都整理清楚形成表格。

a) 一般每个频段有一个发送通路，两个接受通路（4G要求的），主天线通路和分集天线通路。rx0, rx1, tx0，主天线通路默认是rx0。

b) 有的频段没有分集天线通路，如tdscmda B34

c) 有的接收回路几个频段共用一条线：G900/B8, G850/B5, G1900/B2, G1800/B3, B1/B4,B38/B41

改动编译文件scons

在文件modem_proc/rfc_dime/build/modem_rfc_dime.scons里加入include目录

env.PublishProtectedApi('RFC_RF_CARD_INC', [

'${RFC_ROOT}/rf_card/rfc_wtr1625_vz_sv2/common/inc',

'${RFC_ROOT}/rf_card/rfc_wtr1625_bacon/common/inc'

])

编译软件，看看编译是否通过？编译通过后，进行下一步。

3、加入新的开关器件

a) 在modem_proc/rfdevice_asm/src目录下，复制一个类似的器件，然后改动。

修改modem_proc/rfdevice_asm/src/rfcdevice_asm_factory_ag.cpp，并增加新的ASM驱动

else if ( mfg_id == 0x01A5 && prd_id == 0x5F && prd_rev == 0)

{

asm_data =rfdevice_asm_sky13488_data_ag::get_instance();

}

编译通过后，进行下一步。

4、加入新的PA器件

a) 在目录modem_proc/rfdevice_pa/src，复制一个类似的器件，然后改动。

修改modem_proc/rfdevice_pa/src/rfdevice_pa_factory_ag.cpp，并增加新的PA驱动

else if ( mfg_id == 0x134 && prd_id == 0x30 && prd_rev == 0)

{

pa_data =rfdevice_pa_rfmd_7459_data_ag::get_instance();

}

编译通过后，进行下一步。

5、在rf_card里加上器件，ASM，PA等MIPI接口的器件。这些器件在modem软件启动时会扫描的。

如果用了不是MIPI接口的器件，不用在这里加

modem_proc/rfc_dime/rf_card/rfc_wtr1625_bacon/common/src/rfc_wtr1625_bacon_cmn_ag.cpp

rfc_device_cfg_info_typerfc_wtr1625_bacon_cmn_devices_list[] =

{

{ /*Device: WTR1625 */

RFDEVICE_TRANSCEIVER, /* DEVICE_TYPE */

WTR1625, /* DEVICE_NAME */

0, /* DEVICE_TYPE_INSTANCE */

RFDEVICE_COMM_PROTO_SSBI, /*DEVICE_COMM_PROTOCOL */

{ RFC_DEVICE_COMM_BUS_SSBI_1,RFC_DEVICE_COMM_BUS_SSBI_2,},/* DEVICE_COMM_BUS */

0 /*Warning: Not specified*/,/* MANUFACTURER_ID */

0 /*Warning: Not specified*/, /* PRODUCT_ID */

0 /*Warning: Not specified*/,/* PRODUCT_REV */

0 /*Warning: Not specified*/,/* DEFAULT USID RANGE START */

0 /*Warning: Not specified*/,/* DEFAULT USID RANGE END */

0 /*Warning: Not specified*/,/* ASSIGNED_USID */

0 /*Warning: Not specified*/,/* RFFE_GROUP_ID */

FALSE, /* INIT */

RFC_TX_MODEM_CHAIN_0, /*ASSOCIATED_DAC */

RFDEVICE_TYPE_INVALID, /*ASSOCIATED_DEVICE_TYPE */

0 /*Warning: Not specified*/,/* ASSOCIATED_DEVICE_TYPE_INSTANCE */

}, /* END - Device: WTR1625 */

{ /*Device: QFE1101 */ PAPower Manager，用了管理PA的功率，可以减少电流消耗。发射通道需要

RFDEVICE_PAPM, /* DEVICE_TYPE */

QFE1101, /* DEVICE_NAME */

0, /* DEVICE_TYPE_INSTANCE */

RFDEVICE_COMM_PROTO_RFFE, /*DEVICE_COMM_PROTOCOL */

{ 0,0 /* 0 not specified */,}, /*DEVICE_COMM_BUS */

0x0217, /* MANUFACTURER_ID */

0x30, /* PRODUCT_ID */

0, /* PRODUCT_REV */

0x4, /* DEFAULT USID RANGESTART */

0x4, /* DEFAULT USID RANGE END */

0x4, /* ASSIGNED_USID */

0x4, /* RFFE_GROUP_ID */

TRUE, /* INIT */

RFC_INVALID_PARAM, /*ASSOCIATED_DAC */

RFDEVICE_TYPE_INVALID, /*ASSOCIATED_DEVICE_TYPE */

0 /*Warning: Not specified*/,/* ASSOCIATED_DEVICE_TYPE_INSTANCE */

}, /* END - Device: QFE1100 */

{ /*Device: QFE1550 */ Antanna Tuner，天线调谐器，接收通道用的

RFDEVICE_TUNER, /* DEVICE_TYPE */

QFE1550, /* DEVICE_NAME */

0, /* DEVICE_TYPE_INSTANCE */

RFDEVICE_COMM_PROTO_RFFE, /*DEVICE_COMM_PROTOCOL */

{ RFC_DEVICE_COMM_BUS_SSBI_1,0 /*0 not specified */,}, /* DEVICE_COMM_BUS */

0x0217, /* MANUFACTURER_ID */

0x02, /* PRODUCT_ID */

0, /* PRODUCT_REV */

0x7, /* DEFAULT USID RANGESTART */

0x7, /* DEFAULT USID RANGE END */

0x7, /* ASSIGNED_USID */

0x7, /* RFFE_GROUP_ID */

FALSE, /* INIT */

RFC_INVALID_PARAM, /*ASSOCIATED_DAC */

RFDEVICE_TYPE_INVALID, /*ASSOCIATED_DEVICE_TYPE */

0 /*Warning: Not specified*/,/* ASSOCIATED_DEVICE_TYPE_INSTANCE */

}, /* END - Device: QFE1550 */

{ /*Device: RFMD1500 */ 开关器件

RFDEVICE_ASM, /* DEVICE_TYPE */

GEN_ASM /* ASM_16T */, /* DEVICE_NAME */

0, /* DEVICE_TYPE_INSTANCE */

RFDEVICE_COMM_PROTO_RFFE, /*DEVICE_COMM_PROTOCOL */

{ RFC_DEVICE_COMM_BUS_SSBI_1,0 /*0 not specified */,}, /* DEVICE_COMM_BUS */

0x0134, /* MANUFACTURER_ID */

0x5D, /* PRODUCT_ID */

0, /* PRODUCT_REV */

0xB, /* DEFAULT USID RANGESTART */

0xB, /* DEFAULT USID RANGE END */

0xB, /* ASSIGNED_USID */

0xB, /* RFFE_GROUP_ID */

FALSE, /* INIT */

RFC_INVALID_PARAM, /*ASSOCIATED_DAC */

RFDEVICE_TYPE_INVALID, /*ASSOCIATED_DEVICE_TYPE */

0 /*Warning: Not specified*/,/* ASSOCIATED_DEVICE_TYPE_INSTANCE */

}, /* END - Device: ASM_16T */

{ /*Device: RFMD1660 */ 开关器件

RFDEVICE_ASM, /* DEVICE_TYPE */

GEN_ASM /* ASM_10T */, /* DEVICE_NAME */

1, /* DEVICE_TYPE_INSTANCE */

RFDEVICE_COMM_PROTO_RFFE, /*DEVICE_COMM_PROTOCOL */

{ RFC_DEVICE_COMM_BUS_SSBI_1,0/* 0 not specified */,}, /* DEVICE_COMM_BUS */

0x0134, /* MANUFACTURER_ID */

0x78, /* PRODUCT_ID */

0, /* PRODUCT_REV */

0xA, /* DEFAULT USID RANGESTART */

0xA, /* DEFAULT USID RANGE END*/

0xA, /* ASSIGNED_USID */

0xA, /* RFFE_GROUP_ID */

FALSE, /* INIT */

RFC_INVALID_PARAM, /*ASSOCIATED_DAC */

RFDEVICE_TYPE_INVALID, /*ASSOCIATED_DEVICE_TYPE */

0 /*Warning: Not specified*/,/* ASSOCIATED_DEVICE_TYPE_INSTANCE */

}, /* END - Device: ASM_10T */

{ /*Device: HCPA,RF7459, Same asRF7389 */

RFDEVICE_PA, /* DEVICE_TYPE */ PA器件

GEN_PA /* HCPA */, /*DEVICE_NAME */

0, /* DEVICE_TYPE_INSTANCE */

RFDEVICE_COMM_PROTO_RFFE, /*DEVICE_COMM_PROTOCOL */

{ 0,0 /* 0 not specified */,},/* DEVICE_COMM_BUS */

0x0134, /* MANUFACTURER_ID */

0x30,

0, /* PRODUCT_REV */

0xF, /* DEFAULT USID RANGESTART */

0xF, /* DEFAULT USID RANGE END*/

0xF, /* ASSIGNED_USID */

0xF, /* RFFE_GROUP_ID */

FALSE, /* INIT */

RFC_INVALID_PARAM, /*ASSOCIATED_DAC */

RFDEVICE_TYPE_INVALID, /*ASSOCIATED_DEVICE_TYPE */

0 /*Warning: Not specified*/,/* ASSOCIATED_DEVICE_TYPE_INSTANCE */

}, /* END - Device: HCPA */

{ /*Device: TRX_HDET */ 这个设备没有具体的硬件器件，它是通过某种电路来实现的，需要在软件里加上它。

RFDEVICE_HDET, /* DEVICE_TYPE */

TRX_HDET, /* DEVICE_NAME */

0, /* DEVICE_TYPE_INSTANCE */

RFDEVICE_COMM_PROTO_SSBI, /*DEVICE_COMM_PROTOCOL */

{ RFC_DEVICE_COMM_BUS_SSBI_1,0 /*0 not specified */,}, /* DEVICE_COMM_BUS */

0 /*Warning: Not specified*/,/* MANUFACTURER_ID */

0 /*Warning: Not specified*/, /* PRODUCT_ID */

0 /*Warning: Not specified*/,/* PRODUCT_REV */

0 /*Warning: Not specified*/,/* DEFAULT USID RANGE START */

0 /*Warning: Not specified*/,/* DEFAULT USID RANGE END */

0 /*Warning: Not specified*/,/* ASSIGNED_USID */

0 /*Warning: Not specified*/,/* RFFE_GROUP_ID */

FALSE, /* INIT */

RFC_INVALID_PARAM, /*ASSOCIATED_DAC */

RFDEVICE_TRANSCEIVER, /*ASSOCIATED_DEVICE_TYPE */

0, /* ASSOCIATED_DEVICE_TYPE_INSTANCE */

}, /* END - Device: TRX_HDET*/

{ /*Device: RFDEVICE_INVALID*/

RFDEVICE_TYPE_INVALID, /* DEVICE_TYPE */

RFDEVICE_INVALID, /* DEVICE_NAME */

0 /*Warning: Not specified*/,/* DEVICE_TYPE_INSTANCE */

RFDEVICE_COMM_PROTO_INVALID,/* DEVICE_COMM_PROTOCOL */

{ 0 /* 0 not specified */,0 /* 0not specified */,}, /* DEVICE_COMM_BUS */

0 /*Warning: Not specified*/,/* MANUFACTURER_ID */

0 /*Warning: Not specified*/, /* PRODUCT_ID */

0 /*Warning: Not specified*/,/* PRODUCT_REV */

0 /*Warning: Not specified*/,/* DEFAULT USID RANGE START */

0 /*Warning: Not specified*/,/* DEFAULT USID RANGE END */

0 /*Warning: Not specified*/,/* ASSIGNED_USID */

0 /*Warning: Not specified*/,/* RFFE_GROUP_ID */

FALSE, /* INIT */

RFC_INVALID_PARAM, /*ASSOCIATED_DAC */

RFDEVICE_TYPE_INVALID, /*ASSOCIATED_DEVICE_TYPE */

0 /*Warning: Not specified*/,/* ASSOCIATED_DEVICE_TYPE_INSTANCE */

}, /* END - Device:RFDEVICE_INVALID */

};

6、根据硬件原理图，来配置每一条软件通路

7、配置RX通道，rx0,rx1

modem_proc/rfc_dime/rf_card/rfc_wtr1625_bacon/common/src/rfc_wtr1625_bacon_cmn_ag.cpp

rfm_devices_configuration_typerfc_wtr1625_bacon_logical_device_properties =

{

{ /* Mode Concurrencies: Bit0represents Rx concurrency and Bit1 represents Tx concurrency */

{ 0x0, 0x0, 0x0, 0x0, 0x0,0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, },

{ /* device_support */

{ /* Logical Device 0 */ //rx0 通道配置，支持哪些频段

/* bands_supported */

{

/* Bit mask element 0 */

), /* End Bit mask element 0 */

/* Bit mask element 1 */

(

( (uint64)1<< (SYS_BAND_WCDMA_I_IMT_2000 - 64) ) |

( (uint64)1<< (SYS_BAND_WCDMA_II_PCS_1900 - 64) ) |

( (uint64)1<< (SYS_BAND_WCDMA_III_1700 - 64) ) |

( (uint64)1<< (SYS_BAND_WCDMA_IV_1700 - 64) ) |

( (uint64)1<< (SYS_BAND_WCDMA_V_850 - 64) ) |

( (uint64)1<< (SYS_BAND_WCDMA_VIII_900 - 64) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND1 - 64) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND2 - 64) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND3 - 64) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND4 - 64) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND5 - 64) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND7 - 64) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND8 - 64) )

), /* End Bit mask element 1 */

/* Bit mask element 2 */

(

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND20 - 128) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND38 - 128) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND39 - 128) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND40 - 128) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND41 - 128) ) |

( (uint64)1<< (SYS_BAND_TDS_BANDA - 128) ) |

( (uint64)1<< (SYS_BAND_TDS_BANDF - 128) )

), /* End Bit mask element 2 */

/* ca1_bands_supported */

{

/* Bit mask element 0 */

(

), /* End Bit mask element 0 */

/* Bit mask element 1 */

(

), /* End Bit mask element 1 */

/* Bit mask element 2 */

(

), /* End Bit mask element 2 */

( RFM_DEVICE_RX_SUPPORTED |RFM_DEVICE_TX_SUPPORTED),

RFM_DEVICE_1, /* AssociatedSlave Device for RFM_DEVICE_0 */

}, /* End Logical Device 0 */

{ /* Logical Device 1 */ //rx1 通道配置，支持哪些频段

/* bands_supported */

{

/* Bit mask element 0 */

(

), /* End Bit mask element 0 */

/* Bit mask element 1 */

(

( (uint64)1<< (SYS_BAND_WCDMA_I_IMT_2000 - 64) ) |

( (uint64)1<< (SYS_BAND_WCDMA_II_PCS_1900 - 64) ) |

( (uint64)1<< (SYS_BAND_WCDMA_III_1700 - 64) ) |

( (uint64)1<< (SYS_BAND_WCDMA_IV_1700 - 64) ) |

( (uint64)1<< (SYS_BAND_WCDMA_V_850 - 64) ) |

( (uint64)1<< (SYS_BAND_WCDMA_VIII_900 - 64) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND1 - 64) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND2 - 64) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND3 - 64) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND4 - 64) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND5 - 64) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND7 - 64) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND8 - 64) )

), /* End Bit mask element 1 */

/* Bit mask element 2 */

(

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND20 - 128) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND38 - 128) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND39 - 128) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND40 - 128) ) |

( (uint64)1<< (SYS_BAND_LTE_EUTRAN_BAND41 - 128) )

), /* End Bit mask element 2 */

/* ca1_bands_supported */

{

/* Bit mask element 0 */

(

), /* End Bit mask element 0 */

/* Bit mask element 1 */

(

), /* End Bit mask element 1 */

/* Bit mask element 2 */

(

), /* End Bit mask element 2 */

( RFM_DEVICE_RX_SUPPORTED),

RFM_INVALID_DEVICE, /*Associated Slave Device for RFM_DEVICE_1 */

}, /* End Logical Device 1 */

8、生成QCN

a) 在目录modem_proc/rftarget_dime/common/qcn，找一个相近的，例如wtr1625_apac，来生成QCN，删除里面不存在的频段，加入有的频段。使之和硬件对应。

b) 根据硬件修改MSM8974_WTR1625_APAC_MASTERFILE.xml里的这些NV项

c) 用QDART来生成QCN

9、调试

a) MIPI器件可以用QDART来做通路测试

b) 连接仪器来做测试，如果不通，通过硬件来量信号，看是什么地方不通。

根据电路配置来说明软件实现

rfc_device_info_typerf_card_wtr1625_bacon_rx0_lte_b1_device_info =

{

0x022902A2, /* Revision: v2.41.674 */

RFC_RX_MODEM_CHAIN_0, /* Modem Chain */

0 /*Warning: Not Specified */, /* ET Modem Chain */

0, /*NV Container */

0 /*Warning: Not Specified */, /* Antenna */

2, /*NUM_DEVICES_TO_CONFIGURE */

{

RFDEVICE_TRANSCEIVER,

WTR1625, /* NAME */

0, /* DEVICE_TYPE_INSTANCE */

0, /* PHY_PATH_NUM */

{

0 /*Warning: Not specified*/, /*INTF_REV */

(int)WTR1625_LTEFDD_PRX_BAND1_PMB4, /*PORT */ W1625上的控制端口，看硬件原理图

( RFDEVICE_PA_LUT_MAPPING_INVALID ), /* RF_ASIC_BAND_PA_LUT_MAP */

FALSE, /* TXAGC_LUT */

0, /* Array Filler */

{

RFDEVICE_ASM,

GEN_ASM /* ASM_16T */, /* NAME */

0, /* DEVICE_TYPE_INSTANCE */

0 /*Warning: Not specified*/, /* PHY_PATH_NUM */

{

0 /* Orig setting: */, /*INTF_REV */

(0x0134 << 22)/*mfg_id*/ | (0x5D<< 14)/*prd_id*/ | (10)/*port_num*/, /* PORT_NUM */ 器件选通通道

0, /* Array Filler */

};

rfc_sig_info_typerf_card_wtr1625_bacon_rx0_lte_b1_sig_cfg =

{

0x022902A2, /* Revision: v2.41.674 */

{

{ (int)RFC_SIG_LIST_END, RFC_LOW }

};

rfc_device_info_typerf_card_wtr1625_bacon_rx1_lte_b1_device_info =

{

0x022902A2, /* Revision: v2.41.674 */

RFC_RX_MODEM_CHAIN_1, /* Modem Chain */

0 /* Warning:Not Specified */, /* ET Modem Chain */

1, /*NV Container */

1 /*Warning: Not Specified */, /* Antenna */

3, /*NUM_DEVICES_TO_CONFIGURE */

{

RFDEVICE_TRANSCEIVER,

WTR1625, /* NAME */

0, /* DEVICE_TYPE_INSTANCE */

1, /* PHY_PATH_NUM */

{

0 /*Warning: Not specified*/, /*INTF_REV */

(int)WTR1625_LTEFDD_DRX_BAND1_DMB1, /*PORT */

( RFDEVICE_PA_LUT_MAPPING_INVALID ), /* RF_ASIC_BAND_PA_LUT_MAP */

FALSE, /* TXAGC_LUT */

0, /* Array Filler */

{

RFDEVICE_ASM,

GEN_ASM /* ASM_10T */, /* NAME */

1, /* DEVICE_TYPE_INSTANCE */

0 /*Warning: Not specified*/, /* PHY_PATH_NUM */

{

0 /* Orig setting: */, /*INTF_REV */

(0x0134 << 22)/*mfg_id*/ | (0x78<< 14)/*prd_id*/ | (8)/*port_num*/, /* PORT_NUM */

0, /* Array Filler */

{

RFDEVICE_TUNER, 从原理图上看，所有的分集天线都通过了Tuner，所以要把这个器件加上

QFE1550, /* NAME */

0, /* DEVICE_TYPE_INSTANCE */

0 /*Warning: Not specified*/, /* PHY_PATH_NUM */

{

0 /* Orig setting: */, /*INTF_REV */

0, /* Array Filler */

};

rfc_sig_info_typerf_card_wtr1625_bacon_rx1_lte_b1_sig_cfg =

{

0x022902A2, /* Revision: v2.41.674 */

{

b1 rx1通过了器件XM0830SJ-DL0612来选通b1或b4，这个器件是通过GPIO120来控制的

{ (int)RFC_WTR1625_BACON_RF_PATH_SEL_05, RFC_HIGH }, /* GPIO_120*/

{ (int)RFC_SIG_LIST_END, RFC_LOW }

};

rfc_device_info_typerf_card_wtr1625_bacon_tx0_lte_b1_device_info =

{

0x022902A2, /* Revision: v2.41.674 */

RFC_TX_MODEM_CHAIN_0, /* Modem Chain */

RFC_TX_MODEM_CHAIN_1, /* ET Modem Chain */

0, /*NV Container */

0 /*Warning: Not Specified */, /* Antenna */

5, /*NUM_DEVICES_TO_CONFIGURE */

{

RFDEVICE_TRANSCEIVER,

WTR1625, /* NAME */

0, /* DEVICE_TYPE_INSTANCE */

0, /* PHY_PATH_NUM */

{

0 /*Warning: Not specified*/, /*INTF_REV */

(int)WTR1625_LTEFDD_TX_BAND1_TMB3, /*PORT */

FALSE, /* TXAGC_LUT */

0, /* Array Filler */

{

RFDEVICE_PA,

GEN_PA, /* NAME */

0, /* DEVICE_TYPE_INSTANCE */

0 /*Warning: Not specified*/, /* PHY_PATH_NUM */

{

0 /* Orig setting: */, /*INTF_REV */

(0x0134 << 22)/*mfg_id*/ | (0x30<< 14)/*prd_id*/ | (22)/*port_num*/, /* PORT_NUM */

0, /* Array Filler */

{ 发射通道需要加上PA Power Manager器件来控制发射功率

RFDEVICE_PAPM,

QFE1101, /* NAME */

0, /* DEVICE_TYPE_INSTANCE */

0 /*Warning: Not specified*/, /* PHY_PATH_NUM */

{

0 /* Orig setting: */, /*INTF_REV */

(0x217 <<22)/*mfg_id*/ | (0x30 << 14)/*prd_id*/ | (9)/*port_num*/, /*PORT_NUM */ 这个没有具体的资料，也是从原来的Code里抄的

0, /* Array Filler */

{

RFDEVICE_ASM,

GEN_ASM /* ASM_16T */, /* NAME */

0, /* DEVICE_TYPE_INSTANCE */

0 /*Warning: Not specified*/, /* PHY_PATH_NUM */

{

0 /* Orig setting: */, /*INTF_REV */

(0x0134 << 22)/*mfg_id*/ | (0x5D<< 14)/*prd_id*/ | (10)/*port_num*/, /* PORT_NUM */

0, /* Array Filler */

{ 没有实际存在的器件对应，可能通过电路来实现，需要加上

RFDEVICE_HDET,

TRX_HDET, /* NAME */

0, /* DEVICE_TYPE_INSTANCE */

0 /*Warning: Not specified*/, /* PHY_PATH_NUM */

{

0 /* Orig setting: */, /*INTF_REV */

0, /* Array Filler */

};

rfc_sig_info_typerf_card_wtr1625_bacon_tx0_lte_b1_sig_cfg =

{

0x022902A2, /* Revision: v2.41.674 */

{

{ (int)RFC_WTR1625_BACON_TX_GTR_TH, RFC_CONFIG_ONLY }, 这两项不加也可以，加在这里是从原有文件里带的

{ (int)RFC_WTR1625_BACON_PA_IND, RFC_CONFIG_ONLY },

{ (int)RFC_SIG_LIST_END, RFC_LOW }

};

{

RFDEVICE_PA,

GEN_PA /* HCPA */, /* NAME */

0, /* DEVICE_TYPE_INSTANCE */

0/*Warning: Not specified*/, /* PHY_PATH_NUM */

{

0 /* Orig setting: */, /* INTF_REV */

(0x01A5 << 22)/*mfg_id*/ | (0x09 << 14)/*prd_id*/ | (13 << 7)/*sec_port_num*/ | (9)/*port_num*/, /* PORT_NUM */ 这个sec_port_num也是从原来code里抄的，应该不需要

0, /* Array Filler */

司马如风

关注

3
点赞
踩
11

收藏

觉得还不错? 一键收藏
1
评论
复制链接

分享到 QQ

分享到新浪微博

扫一扫

专栏目录