t113-s3 tina-linux 适配 tft-lcd 面板

于 2025-04-24 17:22:57 发布
阅读量210 收藏 3
点赞数 7
分类专栏： 全志T113-S3 文章标签： 驱动开发 嵌入式硬件 linux c语言 单片机 pcb工艺 硬件工程
版权声明：本文为博主原创文章，遵循 CC 4.0 BY-SA 版权协议，转载请附上原文出处链接和本声明。
本文链接：https://blog.csdn.net/qq_39029441/article/details/147483039
版权

适配 86 盒屏幕

86 屏使用的是 ST7701 芯片，RGB 接口，需要 SPI 初始化才可以使用，所以需要增加初始化代码。

参考文档：https://blog.csdn.net/weixin_43094346/article/details/127082843

关闭 uboot disp2

如果希望关闭 U-Boot 的 LCD DISP 驱动输出，可以注释掉 CONFIG_DISP2_SUNXI=y 这一行

vim lichee/brandy-2.0/u-boot-2018/configs/sun8iw20p1_bingpi-m2_defconfig
vim lichee/brandy-2.0/u-boot-2018/configs/sun8iw20p1_defconfig
vim device/config/chips/t113/configs/bingpi_m2/configs/config-uboot

添加 .c .h

下方给出了代码，此处使用了IO来模拟实现 9 bit spi：

https://gist.github.com/FanhuaCloud/b0f72ceb4ec5e8cefe6c0d2d65fb12cb

https://gist.github.com/FanhuaCloud/cbb54819bd40cabc498134bc73074208

将 st7701_86.h，st7701_86.c 放入下方文件中：

vim lichee/linux-5.4/drivers/video/fbdev/sunxi/disp2/disp/lcd/st7701_86.c

/*
 * drivers/video/fbdev/sunxi/disp2/disp/lcd/st7701_86/st7701_86.c
 *
 * Copyright (c) 2007-2018 Allwinnertech Co., Ltd.
 * Author: zhengxiaobin <zhengxiaobin@allwinnertech.com>
 *
 * This software is licensed under the terms of the GNU General Public
 * License version 2, as published by the Free Software Foundation, and
 * may be copied, distributed, and modified under those terms.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
[lcd0]
lcd_used            = 1

lcd_driver_name     = "st7701_86"
lcd_x               = 480
lcd_y               = 480
lcd_width           = 71
lcd_height          = 71
lcd_dclk_freq       = 30

lcd_pwm_used        = 1
lcd_pwm_ch          = 8
lcd_pwm_freq        = 50000
lcd_pwm_pol         = 0
lcd_pwm_max_limit   = 255

lcd_hbp             = 120
;10 + 20 + 10 + 240*3 = 760  real set 1000
lcd_ht              = 850
lcd_hspw            = 2
lcd_vbp             = 13
lcd_vt              = 373
lcd_vspw            = 2

lcd_frm             = 1
lcd_if              = 0
lcd_hv_if			= 8
lcd_hv_clk_phase    = 0
lcd_hv_sync_polarity   = 0
lcd_hv_srgb_seq		= 0

lcd_io_phase        = 0x0000
lcd_gamma_en        = 0
lcd_bright_curve_en = 1
lcd_cmap_en         = 0


lcd_rb_swap	= 0

deu_mode            = 0
lcdgamma4iep        = 22
smart_color         = 90

;lcd_bl_en           = port:PB03<1><0><default><1>
lcd_power           = "vcc-lcd"
lcd_pin_power           = "vcc-pd"

;reset
lcd_gpio_0          = port:PD09<1><0><default><1>
;cs
lcd_gpio_1          = port:PD10<1><0><default><0>
;sda
lcd_gpio_2          = port:PD13<1><0><default><0>
;sck
lcd_gpio_3          = port:PD12<1><0><default><0>


lcdd5                = port:PD03<2><0><2><default>
lcdd6                = port:PD04<2><0><2><default>
lcdd7                = port:PD05<2><0><2><default>
lcdd10               = port:PD06<2><0><2><default>
lcdd11               = port:PD07<2><0><2><default>
lcdd12               = port:PD08<2><0><2><default>

lcdclk              = port:PD18<2><0><3><default>
lcdde               = port:PD19<2><0><3><default>
lcdhsync            = port:PD20<2><0><3><default>
lcdvsync            = port:PD21<2><0><3><default>

[lcd0_suspend]

lcdd5                = port:PD03<7><0><2><default>
lcdd6                = port:PD04<7><0><2><default>
lcdd7                = port:PD05<7><0><2><default>
lcdd10               = port:PD06<7><0><2><default>
lcdd11               = port:PD07<7><0><2><default>
lcdd12               = port:PD08<7><0><2><default>

lcdclk              = port:PD18<7><0><3><default>
lcdde               = port:PD19<7><0><3><default>
lcdhsync            = port:PD20<7><0><3><default>
lcdvsync            = port:PD21<7><0><3><default>
 */
#include "st7701_86.h"

#define spi_scl_1 sunxi_lcd_gpio_set_value(0, 3, 1)
#define spi_scl_0 sunxi_lcd_gpio_set_value(0, 3, 0)
#define spi_sdi_1 sunxi_lcd_gpio_set_value(0, 2, 1)
#define spi_sdi_0 sunxi_lcd_gpio_set_value(0, 2, 0)
#define spi_cs_1 sunxi_lcd_gpio_set_value(0, 1, 1)
#define spi_cs_0 sunxi_lcd_gpio_set_value(0, 1, 0)

static void lcd_panel_st7701_86_init(void);
static void LCD_power_on(u32 sel);
static void LCD_power_off(u32 sel);
static void LCD_bl_open(u32 sel);
static void LCD_bl_close(u32 sel);

static void LCD_panel_init(u32 sel);
static void LCD_panel_exit(u32 sel);

static void LCD_cfg_panel_info(struct panel_extend_para *info)
{
  printk("\n\n\n>>>>>>119.st7701,st7701_86.c,LCD_cfg_panel_info()\n\n\n");
	u32 i = 0, j = 0;
	u32 items;
	u8 lcd_gamma_tbl[][2] = {
	    /* {input value, corrected value} */
	    {0, 0},     {15, 15},   {30, 30},   {45, 45},   {60, 60},
	    {75, 75},   {90, 90},   {105, 105}, {120, 120}, {135, 135},
	    {150, 150}, {165, 165}, {180, 180}, {195, 195}, {210, 210},
	    {225, 225}, {240, 240}, {255, 255},
	};

	u32 lcd_cmap_tbl[2][3][4] = {
	    {
		{LCD_CMAP_G0, LCD_CMAP_B1, LCD_CMAP_G2, LCD_CMAP_B3},
		{LCD_CMAP_B0, LCD_CMAP_R1, LCD_CMAP_B2, LCD_CMAP_R3},
		{LCD_CMAP_R0, LCD_CMAP_G1, LCD_CMAP_R2, LCD_CMAP_G3},
	    },
	    {
		{LCD_CMAP_B3, LCD_CMAP_G2, LCD_CMAP_B1, LCD_CMAP_G0},
		{LCD_CMAP_R3, LCD_CMAP_B2, LCD_CMAP_R1, LCD_CMAP_B0},
		{LCD_CMAP_G3, LCD_CMAP_R2, LCD_CMAP_G1, LCD_CMAP_R0},
	    },
	};

	items = sizeof(lcd_gamma_tbl) / 2;
	for (i = 0; i < items - 1; i++) {
		u32 num = lcd_gamma_tbl[i + 1][0] - lcd_gamma_tbl[i][0];

		for (j = 0; j < num; j++) {
			u32 value = 0;

			value =
			    lcd_gamma_tbl[i][1] +
			    ((lcd_gamma_tbl[i + 1][1] - lcd_gamma_tbl[i][1]) *
			     j) /
				num;
			info->lcd_gamma_tbl[lcd_gamma_tbl[i][0] + j] =
			    (value << 16) + (value << 8) + value;
		}
	}
	info->lcd_gamma_tbl[255] = (lcd_gamma_tbl[items - 1][1] << 16) +
				   (lcd_gamma_tbl[items - 1][1] << 8) +
				   lcd_gamma_tbl[items - 1][1];

	memcpy(info->lcd_cmap_tbl, lcd_cmap_tbl, sizeof(lcd_cmap_tbl));
}

static s32 LCD_open_flow(u32 sel)
{
  printk("\n\n\n>>>>>>168.st7701,st7701_86.c,LCD_open_flow()\n\n\n");
	/* open lcd power, and delay 50ms */
	LCD_OPEN_FUNC(sel, LCD_power_on, 200);
	/* open lcd power, than delay 200ms */
	LCD_OPEN_FUNC(sel, LCD_panel_init, 200);
	/* open lcd controller, and delay 100ms */
	LCD_OPEN_FUNC(sel, sunxi_lcd_tcon_enable, 150);
	/* open lcd backlight, and delay 0ms */
	LCD_OPEN_FUNC(sel, LCD_bl_open, 0);

	return 0;
}

static s32 LCD_close_flow(u32 sel)
{
  printk("\n\n\n>>>>>>183.st7701,st7701_86.c,LCD_close_flow()\n\n\n");
	/* close lcd backlight, and delay 0ms */
	LCD_CLOSE_FUNC(sel, LCD_bl_close, 50);
	/* close lcd controller, and delay 0ms */
	LCD_CLOSE_FUNC(sel, sunxi_lcd_tcon_disable, 10);
	/* open lcd power, than delay 200ms */
	LCD_CLOSE_FUNC(sel, LCD_panel_exit, 10);
	/* close lcd power, and delay 500ms */
	LCD_CLOSE_FUNC(sel, LCD_power_off, 10);

	return 0;
}

static void LCD_power_on(u32 sel)
{
  printk("\n\n\n>>>>>>198.st7701,st7701_86.c,LCD_power_on()\n\n\n");
	/* config lcd_power pin to open lcd power0 */
	sunxi_lcd_power_enable(sel, 0);
	/* pwr_en, active low */
	sunxi_lcd_gpio_set_value(sel, 3, 0);
	sunxi_lcd_pin_cfg(sel, 1);
}

static void LCD_power_off(u32 sel)
{
  printk("\n\n\n>>>>>>208.st7701,st7701_86.c,LCD_power_off()\n\n\n");
	sunxi_lcd_pin_cfg(sel, 0);
	/* pwr_en, active low */
	sunxi_lcd_gpio_set_value(sel, 3, 1);
	/* config lcd_power pin to close lcd power0 */
	sunxi_lcd_power_disable(sel, 0);
}

static void LCD_bl_open(u32 sel)
{
  printk("\n\n\n>>>>>>218.st7701,st7701_86.c,LCD_bl_open()\n\n\n");
	sunxi_lcd_pwm_enable(sel);
	/* config lcd_bl_en pin to open lcd backlight */
	sunxi_lcd_backlight_enable(sel);
}

static void LCD_bl_close(u32 sel)
{
  printk("\n\n\n>>>>>>226.st7701,st7701_86.c,LCD_bl_close()\n\n\n");
	/* config lcd_bl_en pin to close lcd backlight */
	sunxi_lcd_backlight_disable(sel);
	sunxi_lcd_pwm_disable(sel);
}

static void st7701_86_spi_write_cmd(u8 value)
{

    int i;
    spi_cs_0;
    spi_sdi_0;
    spi_scl_0;
    sunxi_lcd_delay_us(10);
    spi_scl_1;
    for (i = 0; i < 8; i++) {
        sunxi_lcd_delay_us(10);
        if (value & 0x80)
            spi_sdi_1;
        else
            spi_sdi_0;
        spi_scl_0;
        sunxi_lcd_delay_us(10);
        spi_scl_1;
        value <<= 1;
    }
    sunxi_lcd_delay_us(10);
    spi_cs_1;
}

static void st7701_86_spi_write_data(u8 value)
{

    int i;
    spi_cs_0;
    spi_sdi_1;
    spi_scl_0;
    sunxi_lcd_delay_us(10);
    spi_scl_1;
    for (i = 0; i < 8; i++) {
        sunxi_lcd_delay_us(10);
        if (value & 0x80)
            spi_sdi_1;
        else
            spi_sdi_0;
        value <<= 1;
        sunxi_lcd_delay_us(10);
        spi_scl_0;
        spi_scl_1;
    }
    sunxi_lcd_delay_us(10);
    spi_cs_1;
}

static void LCD_panel_init(u32 sel)
{
  printk("\n\n\n>>>>>>282.st7701,st7701_86.c,LCD_panel_init()\n\n\n");
	struct disp_panel_para *info =
	    kmalloc(sizeof(struct disp_panel_para), GFP_KERNEL | __GFP_ZERO);
	bsp_disp_get_panel_info(sel, info);
	lcd_panel_st7701_86_init();
	kfree(info);
	return;
}

static void LCD_panel_exit(u32 sel)
{
  printk("\n\n\n>>>>>>293.st7701,st7701_86.c,LCD_panel_exit()\n\n\n");
	struct disp_panel_para *info =
	    kmalloc(sizeof(struct disp_panel_para), GFP_KERNEL | __GFP_ZERO);
	st7701_86_spi_write_cmd(0x28);
	st7701_86_spi_write_cmd(0x10);
	sunxi_lcd_delay_ms(300);
	bsp_disp_get_panel_info(sel, info);
	kfree(info);
	return;
}

static void lcd_panel_st7701_86_init(void)
{
  printk("\n\n\n>>>>>>306.st7701,st7701_86.c,lcd_panel_st7701_86_init()\n\n\n");
	/* VCI=3.3V */
	/************* Reset LCD Driver ****************/
	spi_cs_0;
	sunxi_lcd_gpio_set_value(0, 0, 1);
	sunxi_lcd_delay_ms(50);
	sunxi_lcd_gpio_set_value(0, 0, 0);
	/* Delay 10ms, This delay time is necessary */
	sunxi_lcd_delay_ms(100);
	sunxi_lcd_gpio_set_value(0, 0, 1);
	/* Delay 120 ms */
	sunxi_lcd_delay_ms(150);

	/******************************************************************************/
	st7701_86_spi_write_cmd(0xFF);
	st7701_86_spi_write_data(0x77);
	st7701_86_spi_write_data(0x01);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x13);
	st7701_86_spi_write_cmd(0xEF);
	st7701_86_spi_write_data(0x08);
	st7701_86_spi_write_cmd(0xFF);
	st7701_86_spi_write_data(0x77);
	st7701_86_spi_write_data(0x01);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x10);
	st7701_86_spi_write_cmd(0xC0);
	st7701_86_spi_write_data(0x3B);
	st7701_86_spi_write_data(0x00);

	st7701_86_spi_write_cmd(0xC1);
	st7701_86_spi_write_data(0x0D);
	st7701_86_spi_write_data(0x02);

	st7701_86_spi_write_cmd(0xC2);
	st7701_86_spi_write_data(0x21);
	st7701_86_spi_write_data(0x08);

	st7701_86_spi_write_cmd(
		0xC3); //配置工作模式为DE模式，供应商给的驱动源码并没有设置该 地址 。
	st7701_86_spi_write_data(
		0x02); // 0X02 The data is input on the negative edge of DOTCLK
	st7701_86_spi_write_data(0x02);
	st7701_86_spi_write_data(0x00);

	st7701_86_spi_write_cmd(0xCD);
	st7701_86_spi_write_data(
		0x08); //18-bit/pixel: MDT=0:D[21:16]=R,D[13:8]=G,D[5:0]=B(CDH=00) ;

	//              MDT=1:D[17:12]=R,D[11:6]=G,D[5:0]=B(CDH=08) ;

	st7701_86_spi_write_cmd(0xB0);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x11);
	st7701_86_spi_write_data(0x18);
	st7701_86_spi_write_data(0x0E);
	st7701_86_spi_write_data(0x11);
	st7701_86_spi_write_data(0x06);
	st7701_86_spi_write_data(0x07);
	st7701_86_spi_write_data(0x08);
	st7701_86_spi_write_data(0x07);
	st7701_86_spi_write_data(0x22);
	st7701_86_spi_write_data(0x04);
	st7701_86_spi_write_data(0x12);
	st7701_86_spi_write_data(0x0F);
	st7701_86_spi_write_data(0xAA);
	st7701_86_spi_write_data(0x31);
	st7701_86_spi_write_data(0x18);
	st7701_86_spi_write_cmd(0xB1);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x11);
	st7701_86_spi_write_data(0x19);
	st7701_86_spi_write_data(0x0E);
	st7701_86_spi_write_data(0x12);
	st7701_86_spi_write_data(0x07);
	st7701_86_spi_write_data(0x08);
	st7701_86_spi_write_data(0x08);
	st7701_86_spi_write_data(0x08);
	st7701_86_spi_write_data(0x22);
	st7701_86_spi_write_data(0x04);
	st7701_86_spi_write_data(0x11);
	st7701_86_spi_write_data(0x11);
	st7701_86_spi_write_data(0xA9);
	st7701_86_spi_write_data(0x32);
	st7701_86_spi_write_data(0x18);
	st7701_86_spi_write_cmd(0xFF);
	st7701_86_spi_write_data(0x77);
	st7701_86_spi_write_data(0x01);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x11);
	st7701_86_spi_write_cmd(0xB0);
	st7701_86_spi_write_data(0x60);
	st7701_86_spi_write_cmd(0xB1);
	st7701_86_spi_write_data(0x30);
	st7701_86_spi_write_cmd(0xB2);
	st7701_86_spi_write_data(0x87);
	st7701_86_spi_write_cmd(0xB3);
	st7701_86_spi_write_data(0x80);
	st7701_86_spi_write_cmd(0xB5);
	st7701_86_spi_write_data(0x49);
	st7701_86_spi_write_cmd(0xB7);
	st7701_86_spi_write_data(0x85);
	st7701_86_spi_write_cmd(0xB8);
	st7701_86_spi_write_data(0x21);
	st7701_86_spi_write_cmd(0xC1);
	st7701_86_spi_write_data(0x78);
	st7701_86_spi_write_cmd(0xC2);
	st7701_86_spi_write_data(0x78);
	sunxi_lcd_delay_ms(20);
	st7701_86_spi_write_cmd(0xE0);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x1B);
	st7701_86_spi_write_data(0x02);
	st7701_86_spi_write_cmd(0xE1);
	st7701_86_spi_write_data(0x08);
	st7701_86_spi_write_data(0xA0);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x07);
	st7701_86_spi_write_data(0xA0);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x44);
	st7701_86_spi_write_data(0x44);
	st7701_86_spi_write_cmd(0xE2);
	st7701_86_spi_write_data(0x11);
	st7701_86_spi_write_data(0x11);
	st7701_86_spi_write_data(0x44);
	st7701_86_spi_write_data(0x44);
	st7701_86_spi_write_data(0xED);
	st7701_86_spi_write_data(0xA0);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0xEC);
	st7701_86_spi_write_data(0xA0);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_cmd(0xE3);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x11);
	st7701_86_spi_write_data(0x11);
	st7701_86_spi_write_cmd(0xE4);
	st7701_86_spi_write_data(0x44);
	st7701_86_spi_write_data(0x44);
	st7701_86_spi_write_cmd(0xE5);
	st7701_86_spi_write_data(0x0A);
	st7701_86_spi_write_data(0xE9);
	st7701_86_spi_write_data(0xD8);
	st7701_86_spi_write_data(0xA0);
	st7701_86_spi_write_data(0x0C);
	st7701_86_spi_write_data(0xEB);
	st7701_86_spi_write_data(0xD8);
	st7701_86_spi_write_data(0xA0);
	st7701_86_spi_write_data(0x0E);
	st7701_86_spi_write_data(0xED);
	st7701_86_spi_write_data(0xD8);
	st7701_86_spi_write_data(0xA0);
	st7701_86_spi_write_data(0x10);
	st7701_86_spi_write_data(0xEF);
	st7701_86_spi_write_data(0xD8);
	st7701_86_spi_write_data(0xA0);
	st7701_86_spi_write_cmd(0xE6);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x11);
	st7701_86_spi_write_data(0x11);
	st7701_86_spi_write_cmd(0xE7);
	st7701_86_spi_write_data(0x44);
	st7701_86_spi_write_data(0x44);
	st7701_86_spi_write_cmd(0xE8);
	st7701_86_spi_write_data(0x09);
	st7701_86_spi_write_data(0xE8);
	st7701_86_spi_write_data(0xD8);
	st7701_86_spi_write_data(0xA0);
	st7701_86_spi_write_data(0x0B);
	st7701_86_spi_write_data(0xEA);
	st7701_86_spi_write_data(0xD8);
	st7701_86_spi_write_data(0xA0);
	st7701_86_spi_write_data(0x0D);
	st7701_86_spi_write_data(0xEC);
	st7701_86_spi_write_data(0xD8);
	st7701_86_spi_write_data(0xA0);
	st7701_86_spi_write_data(0x0F);
	st7701_86_spi_write_data(0xEE);
	st7701_86_spi_write_data(0xD8);
	st7701_86_spi_write_data(0xA0);
	st7701_86_spi_write_cmd(0xEB);
	st7701_86_spi_write_data(0x02);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0xE4);
	st7701_86_spi_write_data(0xE4);
	st7701_86_spi_write_data(0x88);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x40);
	st7701_86_spi_write_cmd(0xEC);
	st7701_86_spi_write_data(0x3C);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_cmd(0xED);
	st7701_86_spi_write_data(0xAB);
	st7701_86_spi_write_data(0x89);
	st7701_86_spi_write_data(0x76);
	st7701_86_spi_write_data(0x54);
	st7701_86_spi_write_data(0x02);
	st7701_86_spi_write_data(0xFF);
	st7701_86_spi_write_data(0xFF);
	st7701_86_spi_write_data(0xFF);
	st7701_86_spi_write_data(0xFF);
	st7701_86_spi_write_data(0xFF);
	st7701_86_spi_write_data(0xFF);
	st7701_86_spi_write_data(0x20);
	st7701_86_spi_write_data(0x45);
	st7701_86_spi_write_data(0x67);
	st7701_86_spi_write_data(0x98);
	st7701_86_spi_write_data(0xBA);
	st7701_86_spi_write_cmd(0xEF);
	st7701_86_spi_write_data(0x10);
	st7701_86_spi_write_data(0x0D);
	st7701_86_spi_write_data(0x04);
	st7701_86_spi_write_data(0x08);
	st7701_86_spi_write_data(0x3F);
	st7701_86_spi_write_data(0x1F);
	st7701_86_spi_write_cmd(0xFF);
	st7701_86_spi_write_data(0x77);
	st7701_86_spi_write_data(0x01);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x00);

	st7701_86_spi_write_cmd(0x3A);
	st7701_86_spi_write_data(
		0x66); //55/50=16bit(RGB565);66=18bit(RGB666);77?????3AH?=24bit(RGB888)

	st7701_86_spi_write_cmd(0xFF);
	st7701_86_spi_write_data(0x77);
	st7701_86_spi_write_data(0x01);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x13);
	st7701_86_spi_write_cmd(0xE8);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x0E);
	st7701_86_spi_write_cmd(0xFF);
	st7701_86_spi_write_data(0x77);
	st7701_86_spi_write_data(0x01);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x00);

	st7701_86_spi_write_cmd(0xFF);
	st7701_86_spi_write_data(0x77);
	st7701_86_spi_write_data(0x01);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x13);
	st7701_86_spi_write_cmd(0xE8);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x0C);
	sunxi_lcd_delay_ms(10);
	st7701_86_spi_write_cmd(0xE8);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x00);

	st7701_86_spi_write_cmd(0xFF);
	st7701_86_spi_write_data(0x77);
	st7701_86_spi_write_data(0x01);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x00);
	st7701_86_spi_write_data(0x00);

	st7701_86_spi_write_cmd(0x35);
	st7701_86_spi_write_data(0x00); //TE ON

	st7701_86_spi_write_cmd(0x36);
	st7701_86_spi_write_data(0x08); //FW:00     BW:10

	st7701_86_spi_write_cmd(0x21);

	///BIST
	// st7701_86_spi_write_cmd(0xFF);
	// st7701_86_spi_write_data(0x77);
	// st7701_86_spi_write_data(0x01);
	// st7701_86_spi_write_data(0x00);
	// st7701_86_spi_write_data(0x00);
	// st7701_86_spi_write_data(0x12);
	// st7701_86_spi_write_cmd(0xD1);
	// st7701_86_spi_write_data(0x81);
	// st7701_86_spi_write_cmd(0xD2);
	// st7701_86_spi_write_data(0x06);

	st7701_86_spi_write_cmd(0x11);
	sunxi_lcd_delay_ms(120);

	st7701_86_spi_write_cmd(0x29);
	sunxi_lcd_delay_ms(120);
}

/* sel: 0:lcd0; 1:lcd1 */
static s32 LCD_user_defined_func(u32 sel, u32 para1, u32 para2, u32 para3)
{
	return 0;
}

struct __lcd_panel st7701_86_panel = {
    /* panel driver name, must mach the name of lcd_drv_name in sys_config.fex
       */
	.name = "st7701_86",
	.func = {
		.cfg_panel_info = LCD_cfg_panel_info,
		.cfg_open_flow = LCD_open_flow,
		.cfg_close_flow = LCD_close_flow,
		.lcd_user_defined_func = LCD_user_defined_func,
		},
};

void st7701_86_init_00A(void) {
  printk("\n\n\n>>>>>>626.st7701,st7701_86.c,st7701_86_init_00A()\n\n\n");
  LCD_power_on(0);sunxi_lcd_delay_ms(200);
  LCD_panel_init(0);sunxi_lcd_delay_ms(200);
  sunxi_lcd_tcon_enable(0);sunxi_lcd_delay_ms(150);
  LCD_bl_open(0);sunxi_lcd_delay_ms(200);
}

vim lichee/linux-5.4/drivers/video/fbdev/sunxi/disp2/disp/lcd/st7701_86.h

/*
 * drivers/video/fbdev/sunxi/disp2/disp/lcd/st7789v/st7789v.h
 *
 * Copyright (c) 2007-2018 Allwinnertech Co., Ltd.
 * Author: zhengxiaobin <zhengxiaobin@allwinnertech.com>
 *
 * This software is licensed under the terms of the GNU General Public
 * License version 2, as published by the Free Software Foundation, and
 * may be copied, distributed, and modified under those terms.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 */
#ifndef __ST7701_86_PANEL_H__
#define __ST7701_86_PANEL_H__

#include "panels.h"

extern struct __lcd_panel st7701_86_panel;

#endif

修改 Kconfig

vim lichee/brandy-2.0/u-boot-2018/drivers/video/sunxi/disp2/disp/lcd/Kconfig

vim lichee/linux-5.4/drivers/video/fbdev/sunxi/disp2/disp/lcd/Kconfig

config LCD_SUPPORT_ST7701_86
	bool "LCD support ST7701_86 panel"
	default n
	---help---
		If you want to support ST7701_86 panel for display driver, select it.

修改 panels.c panels.h

  • 修改 panels.c 增加屏幕指针
  • vim lichee/linux-5.4/drivers/video/fbdev/sunxi/disp2/disp/lcd/panels.c
#ifdef CONFIG_LCD_SUPPORT_ST7701_86
	&st7701_86_panel,
#endif

void st7701_86_init_00A(void);

int lcd_init(void)
{
        printk("\n\n\n>>>>>>36.st7701,st7701_86.c,lcd_init()\n\n\n");
        sunxi_disp_get_source_ops(&g_lcd_drv.src_ops);
        lcd_set_panel_funs();
        st7701_86_init_00A();

        return 0;
}
  • panels.h
  • vim lichee/linux-5.4/drivers/video/fbdev/sunxi/disp2/disp/lcd/panels.h

指针的声明位于头文件中，需要确认声明与panel.c中的名称是否一致

#ifdef CONFIG_LCD_SUPPORT_ST7701_86
extern struct __lcd_panel st7701_86_panel;
#endif

修改 Makefile

接着添加屏幕到上一级目录的 Makefile 中

vim lichee/brandy-2.0/u-boot-2018/drivers/video/sunxi/disp2/disp/Makefile

vim lichee/linux-5.4/drivers/video/fbdev/sunxi/disp2/disp/Makefile

disp-$(CONFIG_LCD_SUPPORT_ST7701_86) += lcd/st7701_86.o

内核选中 st7701_86 面板

make kernel_menuconfig

> Device Drivers
  > Graphics support
    > Frame buffer Devices
      > Video support for sunxi
        > LCD panels select
          [*] LCD support ST7701_86 panel

修改设备树

&lcd0 {
	/* part 1 */
	lcd_used            = <1>;
	lcd_driver_name     = "st7701_86";
	// lcd_backlight	    = <255>;

	/* part 2 */
	lcd_if = <0>;
	lcd_hv_if = <0>;
	
	/* part 3 */
	lcd_x               = <480>;
	lcd_y               = <480>;
	lcd_width           = <71>;
	lcd_height          = <71>;
	lcd_dclk_freq       = <24>;

	lcd_hbp             = <20>;
	lcd_ht              = <526>;
	lcd_hspw            = <6>;

	lcd_vbp             = <10>;
	lcd_vt              = <510>;
	lcd_vspw            = <4>;
		
	lcd_pwm_used        = <1>;
	lcd_pwm_ch          = <7>;
	lcd_pwm_freq        = <10000>;
	lcd_pwm_pol         = <0>;

	/* part 5 */
	lcd_frm = <1>;
	lcd_io_phase = <0x0000>;
	lcd_gamma_en = <0>;
	lcd_cmap_en = <0>;
	lcd_hv_clk_phase = <0>;
	lcd_hv_sync_polarity= <0>;

	// reset
	lcd_gpio_0 = <&pio PB 3 GPIO_ACTIVE_HIGH>;
	// cs
	lcd_gpio_1 = <&pio PB 5 GPIO_ACTIVE_HIGH>;
	// sda
	lcd_gpio_2 = <&pio PB 2 GPIO_ACTIVE_HIGH>;
	// sck
	lcd_gpio_3 = <&pio PB 4 GPIO_ACTIVE_HIGH>;

	/* part 6 */
	lcd_power = "vcc-lcd";
	lcd_pin_power = "vcc-pd";
	pinctrl-0 = <&rgb18_pins_a>;
	pinctrl-1 = <&rgb18_pins_b>;
};

8.打开背光

# pd22 bl
echo 118 > /sys/class/gpio/export
echo out > /sys/class/gpio/gpio118/direction
echo 1 > /sys/class/gpio/gpio118/value

# pb5 cs
echo 37 > /sys/class/gpio/export
echo out > /sys/class/gpio/gpio37/direction
echo 0 > /sys/class/gpio/gpio37/value

fbset

dd if=/dev/urandom of=/dev/fb0 bs=4096 count=1

cat /dev/urandom > /dev/fb0

dmesg | grep -i st7701



echo 1 > /sys/class/disp/disp/attr/colorbar

echo 8 > /sys/class/disp/disp/attr/colorbar
评论 1
添加红包

请填写红包祝福语或标题

个

红包个数最小为10个

元

红包金额最低5元

当前余额3.43元 前往充值 >
需支付：10.00元
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付元
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明：

1.余额是钱包充值的虚拟货币，按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载，可以购买VIP、付费专栏及课程。

余额充值