STM32入门学习之外部中断

最新推荐文章于 2023-12-12 17:29:39 发布

小菜鸟派大星

最新推荐文章于 2023-12-12 17:29:39 发布

阅读量627

点赞数 1

分类专栏： STM32开发学习文章标签： stm32 学习单片机外部中断 LED KEY delay

本文链接：https://blog.csdn.net/qq_43213240/article/details/132010922

版权

STM32开发学习专栏收录该内容

12 篇文章 0 订阅

订阅专栏

1.STM32的IO口可以作为外部中断输入口。本文通过按键按下作为外部中断的输入，点亮LED灯。在STM32的19个外部中断中，0-15为外部IO口的中断输入口。STM32的引脚分别对应着0-15的外部中断线。比如，外部中断线0对应着GPIOA.0-GPIOG.0，以此类推就可以将所以的IO映射到0-15个外部中断线上。STM32的IO的外部中断映射图如下：

2.外部中断的配置步骤：

（1）将IO口映射到对应的外部中断线上，中断线河中断初始化。

（2）配置外部中断，即配置中断管理NVIC。

（3）重写中断服务函数，即中断回调函数。这些中断回调函数在startup_stm32f10x_xx.s中被规定好了名称，我们只需要重写对应的中断回调函数即可。

3.工程代码：

delay.h:

#ifndef __DELAY_H
#define __DELAY_H

#include "stm32f10x.h"

void delay_us(uint32_t us);									//ÑÓÊ±Î¢Ãë
void delay_ms(uint32_t ms);									//ÑÓÊ±ºÁÃë

#endif

delay.c:

#include "delay.h"

void delay_us(uint32_t us)
{
	uint32_t i;
	
	//1.Ñ¡ÔñHCLKÊ±ÖÓ£¬²¢ÉèÖÃµÎ´ðÊ±ÖÓ¼ÆÊýÖµ
	SysTick_Config(72);
	
	for(i = 0;i < us;i++)
	{
		while(!((SysTick->CTRL) & (1 << 16)));		//µÈ´ý¼ÆÊýÍê³É
	}
	SysTick->CTRL &= ~SysTick_CTRL_ENABLE_Msk;	//Ñ¡ÔñSTCLKÊ±ÖÓÔ´£¬²¢Ê§ÄÜ¶¨Ê±Æ÷
}

void delay_ms(uint32_t ms)
{
	uint32_t i;
	//1.Ñ¡ÔñHCLKÊ±ÖÓÔ´£¬²¢ÉèÖÃµÎ´ðÊ±ÖÓ¼ÆÊýÖµ
	SysTick_Config(72000);
	
	for(i = 0;i < ms;i++)
	{
		while(!((SysTick->CTRL) & (1 << 16)));		//µÈ´ý¼ÆÊýÍê³É
	}
	SysTick->CTRL &= ~SysTick_CTRL_ENABLE_Msk;	//Ñ¡ÔñSTCLKÊ±ÖÓÔ´£¬²¢Ê§ÄÜ¶¨Ê±Æ÷
}

key.h:

#ifndef __KEY_H
#define __KEY_H

#include "stm32f10x.h"

#define KEY_0 GPIO_ReadInputDataBit(GPIOC,GPIO_Pin_5)			//¶ÁÈ¡°´¼üµÄ×´Ì¬
#define KEY_1 GPIO_ReadInputDataBit(GPIOA,GPIO_Pin_15)
#define KEY_2 GPIO_ReadInputDataBit(GPIOA,GPIO_Pin_0)

void KEY_Init(void);
void KEY_Scan(void);						//°´¼üÉ¨Ãèº¯Êý

#endif

key.c:

#include "key.h"
#include "delay.h"
#include "led.h"

void KEY_Init(void)
{
	/*1.¶¨ÒåÒý½ÅµÄ½á¹¹Ìå¡£
	  2.Ê¹ÄÜÒý½Å¶ÔÓ¦µÄÊ±ÖÓ¡£
	  3.ÅäÖÃÒý½ÅÐÅÏ¢*/
	
	//¶¨ÒåÒý½Å½á¹¹Ìå£º
	GPIO_InitTypeDef GPIO_InitStruct;
	
	//Ê¹ÄÜÊ±ÖÓ£º
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_GPIOC,ENABLE);
	
	//ÅäÖÃÒý½ÅÐÅÏ¢(KEY0)£º
	GPIO_InitStruct.GPIO_Pin = GPIO_Pin_5;
	GPIO_InitStruct.GPIO_Mode = GPIO_Mode_IPU;
	GPIO_InitStruct.GPIO_Speed = GPIO_Speed_50MHz;
	
	GPIO_Init(GPIOC,&GPIO_InitStruct);
	
	//ÅäÖÃKEY1£º
	GPIO_InitStruct.GPIO_Pin = GPIO_Pin_15;
	GPIO_InitStruct.GPIO_Mode = GPIO_Mode_IPU; //ÉèÖÃ³ÉÉÏÀÊäÈë

	GPIO_Init(GPIOA,&GPIO_InitStruct);
	
	//ÅäÖÃ°´¼üWK_UP:
	GPIO_InitStruct.GPIO_Pin = GPIO_Pin_0;
	GPIO_InitStruct.GPIO_Mode = GPIO_Mode_IPD;
	GPIO_Init(GPIOA,&GPIO_InitStruct);
	
	LED_Init();									//³õÊ¼»¯LED
}

void KEY_Scan(void)
{
	static u8 key_up = 1;				//°´¼üËÉ¿ª±êÖ¾Î»
	if(key_up && (KEY_0 == 0||  KEY_1  == 0|| KEY_1 == 1))
	{
		delay_ms(10);						  //È¥¶¶¶¯
		key_up = 0;
		if(KEY_0 == 0)
		{
			GPIO_ResetBits(GPIOD ,GPIO_Pin_2);
			GPIO_SetBits(GPIOA,GPIO_Pin_8);
			//delay_ms(1000);
		}
		else if(KEY_1 == 0)
		{
			GPIO_ResetBits(GPIOA ,GPIO_Pin_8);
			GPIO_SetBits(GPIOD,GPIO_Pin_2);
			//delay_ms(1000);
		}
		else if(KEY_2 == 1)
		{
			GPIO_ResetBits(GPIOA ,GPIO_Pin_8);
			GPIO_ResetBits(GPIOD ,GPIO_Pin_2);
		}
	}
	else if(KEY_0==1&&KEY_1==1&&KEY_2==0)
	{
		key_up = 1;
	}
}

exti.h:

#ifndef __EXTI_H
#define __EXTI_H

#include "stm32f10x.h"

void EXTIx_Init(void);

#endif

exti.c:

#include "exti.h"
#include "key.h"
#include "delay.h"

void EXTIx_Init(void)
{
	/*Íâ²¿ÖÐ¶ÏµÄÅäÖÃ·½·¨£º
	  1.½«IO¿ÚÓ³Éäµ½¶ÔÓ¦Íâ²¿ÖÐ¶ÏÏßÉÏ
	  2.ÅäÖÃÍâ²¿ÖÐ¶Ï
	  3.ÖØÐ´ÖÐ¶Ï·þÎñº¯Êý£¬¼´ÖÐ¶Ï»Øµ÷º¯Êý*/
	
	//¶¨ÒåÍâ²¿ÖÐ¶ÏºÍÖÐ¶ÏµÄ½á¹¹Ìå£º
	EXTI_InitTypeDef EXTI_InitStructure;
	NVIC_InitTypeDef NVIC_InitStructure;
	
	//Ê¹ÄÜÊ±ÖÓ£º
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO,ENABLE);//Íâ²¿ÖÐ¶ÏÐèÒª¸´ÓÃÊ±ÖÓ
	KEY_Init();			//³õÊ¼»¯°´¼ü
	
	//GPIOC.5µÄÖÐ¶ÏÏßºÍÖÐ¶Ï³õÊ¼»¯ÅäÖÃ£º
	GPIO_EXTILineConfig(GPIO_PortSourceGPIOC,GPIO_PinSource5);	//GPIOÓëÖÐ¶ÏÏß½øÐÐÓ³Éä
	
	EXTI_InitStructure.EXTI_Line = EXTI_Line5;
	EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
	EXTI_InitStructure.EXTI_LineCmd = ENABLE;
	EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising_Falling;
	
	EXTI_Init(&EXTI_InitStructure);//½«ÉÏÃæÅäÖÃµÄÐÅÏ¢Ð´ÈëEXTI¼Ä´æÆ÷ÖÐ
	
	//GPIOA.0µÄÖÐ¶ÏÏßºÍÖÐ¶Ï³õÊ¼»¯ÅäÖÃ£º
	GPIO_EXTILineConfig(GPIO_PortSourceGPIOA,GPIO_PinSource0);	//GPIOÓëÖÐ¶ÏÏß½øÐÐÓ³Éä
	
	EXTI_InitStructure.EXTI_Line = EXTI_Line0;
	EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
	EXTI_InitStructure.EXTI_LineCmd = ENABLE;
	EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising;
	
	EXTI_Init(&EXTI_InitStructure);
	
	//GPIOA.15µÄÖÐ¶ÏÏßºÍÖÐ¶Ï³õÊ¼»¯ÅäÖÃ£º
	GPIO_EXTILineConfig(GPIO_PortSourceGPIOA,GPIO_PinSource15);	//GPIOÓëÖÐ¶ÏÏß½øÐÐÓ³Éä
	
	EXTI_InitStructure.EXTI_Line = EXTI_Line15;
	EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
	EXTI_InitStructure.EXTI_LineCmd = ENABLE;
	EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Falling;
	
	EXTI_Init(&EXTI_InitStructure);
	
	//ÖÐ¶Ï¹ÜÀíÅäÖÃ£º
	NVIC_InitStructure.NVIC_IRQChannel = EXTI0_IRQn;
	NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
	NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 2;
	NVIC_InitStructure.NVIC_IRQChannelSubPriority = 2;
	
	NVIC_Init(&NVIC_InitStructure);
	
	NVIC_InitStructure.NVIC_IRQChannel = EXTI9_5_IRQn;
	NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
	NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 2;
	NVIC_InitStructure.NVIC_IRQChannelSubPriority = 1;
	
	NVIC_Init(&NVIC_InitStructure);
	
	NVIC_InitStructure.NVIC_IRQChannel = EXTI15_10_IRQn;
	NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
	NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 2;
	NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
	
	NVIC_Init(&NVIC_InitStructure);	
}

//ÖØÐ´ÖÐ¶Ï·þÎñº¯Êý.
void EXTI0_IRQHandlÕâÐ©ÖÐ¶Ï»Øµ÷º¯ÊýÔÚstartup_stm32f10x_xx.sÖÐ±»¹æ¶¨ºÃÁËÃû³Æer(void)
{
	//¾²Ì¬±äÁ¿Ö»»áÔÚµÚÒ»´ÎÔËÐÐÊ±±»³õÊ¼»¯¡£ËùÒÔ£¬¿ÉÒÔÀí½âÎªÕâÌõÓï¾äÖ»Ö´ÐÐÒ»´Î
	static u8 flag1 = 1;	
	delay_ms(10);				//Ïû¶¶
	if(KEY_2 == 1)
	{
		if(flag1)
		{
			//GPIO_ResetBits(GPIOD ,GPIO_Pin_2);
			GPIO_SetBits(GPIOA,GPIO_Pin_8);
			flag1 = !flag1;
		}
		else
		{
			GPIO_ResetBits(GPIOA ,GPIO_Pin_8);
			//GPIO_SetBits(GPIOD,GPIO_Pin_2);
			flag1 = !flag1;
		}
	}
	EXTI_ClearITPendingBit(EXTI_Line0);
}

void EXTI9_5_IRQHandler(void)
{
	static u8 flag2 = 1;
	delay_ms(10);				//Ïû¶¶
	if(KEY_0 == 0)
	{
		if(flag2)
		{
			//GPIO_ResetBits(GPIOA,GPIO_Pin_8);
			GPIO_SetBits(GPIOD,GPIO_Pin_2);
			flag2 = !flag2;
		}
		else
		{
			//GPIO_ResetBits(GPIOA,GPIO_Pin_8);
			GPIO_ResetBits(GPIOD,GPIO_Pin_2);
			flag2 = !flag2;
		}
	}
	EXTI_ClearITPendingBit(EXTI_Line5);
}

void EXTI15_10_IRQHandler(void)
{
	static u8 flag3 = 1;
	delay_ms(10);				//Ïû¶¶
	if(KEY_1 == 0)
	{
		if(flag3)
		{
			GPIO_ResetBits(GPIOA,GPIO_Pin_8);
			GPIO_ResetBits(GPIOD,GPIO_Pin_2);
			flag3 = !flag3;
		}
		else
		{
			GPIO_SetBits(GPIOA,GPIO_Pin_8);
			GPIO_SetBits(GPIOD,GPIO_Pin_2);
			flag3 = !flag3;
		}
	}
	EXTI_ClearITPendingBit(EXTI_Line15);
}

main.c:

#include "stm32f10x.h"
#include "delay.h"
#include "led.h"
#include "key.h"
#include "exti.h"

int main(void)
{
	//LED_Init();
	NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2);// ÉèÖÃÖÐ¶ÏÓÅÏÈ¼¶·Ö×é2
	KEY_Init();
	EXTIx_Init();
	while(1)
	{
//		GPIO_ResetBits(GPIOD ,GPIO_Pin_2);
//		GPIO_SetBits(GPIOA,GPIO_Pin_8);
//		delay_ms(1000);
//		GPIO_ResetBits(GPIOA ,GPIO_Pin_8);
//		GPIO_SetBits(GPIOD,GPIO_Pin_2);
//		delay_ms(1000);
		//KEY_Scan();
	}
}

4.运行结果：按下key0，LED1亮，再按一下熄灭。按下key1，LED0亮，再按一下熄灭。按下key3，两个LED亮，再按一下两个LED熄灭。