DHCPv6中继的配置

实验目的：配置路由器作为DHCPv6服务器，为下端所连主机动态的分配IPv6地址

                 配置三层交换机为DHCPv6中继器

实验拓扑图

 配置过程：

LSW2作为集线器，不用做任何配置

交换机1上配置

[Huawei]vlan batch 10 20              

Info: This operation may take a few seconds. Please wait for a moment...done.

[Huawei]ipv6

[Huawei]int g0/0/1

[Huawei-GigabitEthernet0/0/1]port link-type trunk

[Huawei-GigabitEthernet0/0/1]port trunk pvid vlan 10

[Huawei-GigabitEthernet0/0/1]port trunk allow-pass vlan all

[Huawei]int g0/0/2

[Huawei-GigabitEthernet0/0/2]port link-type trunk

[Huawei-GigabitEthernet0/0/2]port trunk pvid vlan 20

[Huawei-GigabitEthernet0/0/2]port trunk allow-pass vlan all

配置vlanif的IP地址

[Huawei]int Vlanif 10

[Huawei-Vlanif10]ipv6 enable

[Huawei-Vlanif10]ipv6 address 2001:0ab2:1111:0001::2 64

[Huawei-Vlanif10]quit

[Huawei]int Vlanif 20

[Huawei-Vlanif20]ipv6 enable

[Huawei-Vlanif20]ipv6 address 2001:0ab2:1111:0002::1 64

[Huawei-Vlanif20]quit

配置vlanif10的DHCP中继功能

[Huawei]int Vlanif 10

[Huawei-Vlanif10]dhcpv6 relay destination 2001:0ab2:1111:0002::2   //目的地址指向路由器的接口地址，因为路由器是DHCPv6的服务器

[Huawei-Vlanif10]undo ipv6 nd ra halt        手动开启发送ra报文

[Huawei-Vlanif10]ipv6 nd autoconfig managed-address-flag      设置标志位，主机通过有状态自动配置获取IPv6地址

[Huawei-Vlanif10]ipv6 nd autoconfig other-flag      设置标志位，主机通过有状态自动配置获取IPv6其他信息

[Huawei-Vlanif10]quit

路由器的配置

[Huawei]ipv6

[Huawei]dhcp enable

Info: The operation may take a few seconds. Please wait for a moment.done.

[Huawei]int g0/0/0

[Huawei-GigabitEthernet0/0/0]ipv6 enable

[Huawei-GigabitEthernet0/0/0]ipv6 address 2001:0ab2:1111:0002::2 64

[Huawei-GigabitEthernet0/0/0]quit

建立DHCPv6地址池

[Huawei]dhcpv6 pool pool10  //地址池名称为pool10

[Huawei-dhcpv6-pool-pool10]address prefix 2001:0ab2:1111:0001::/64

[Huawei-dhcpv6-pool-pool10]excluded-address 2001:0ab2:1111:0001::2

[Huawei-dhcpv6-pool-pool10]quit

进入接口使能地址池

[Huawei]int g0/0/0

[Huawei-GigabitEthernet0/0/0]dhcpv6 server pool10

注意：一定要配置一条缺省路由，让路由器有出去的路由，去分配地址

[Huawei]ipv6 route-static :: 0 2001:0ab2:1111:0002::1

查看结果