原来公司的网络架构可以用拓扑图这样来搭建（详解，不通你来打我！）！！！

---

搭建拓扑图

路由器上接口不够如何添加接口？

如何快速配置路由器接口的ip信息？

互联网主干部分网络配置

DNS服务器的ip配置和DNS解析地址

1、为每个路由器接口配置ip地址和子网掩码

router0配置

Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#interface GigabitEthernet0/1
Router(config-if)#ip address 12.12.12.1 255.255.255.0
Router(config-if)#no shutdown 
Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up

Router(config-if)#
Router(config-if)#exit
Router(config)#interface GigabitEthernet0/2
Router(config-if)#ip address 13.13.13.1 255.255.255.0
Router(config-if)#no sh
Router(config-if)#no shutdown 

Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up

Router(config)#interface GigabitEthernet0/0
Router(config-if)#ip address 192.168.10.2 255.255.255.0
Router(config-if)#no sh
Router(config-if)#no shutdown 

Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up

router1配置

Router(config)#interface GigabitEthernet0/0
Router(config-if)#ip address 12.12.12.2 255.0.0.0
Router(config-if)#ip address 12.12.12.2 255.255.255.0
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#interface GigabitEthernet0/1
Router(config-if)#ip address 23.23.23.1 255.0.0.0
Router(config-if)#ip address 23.23.23.1 255.255.255.0
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up

router2配置

Router(config)#interface GigabitEthernet0/0
Router(config-if)#ip address 13.13.13.2 255.0.0.0
Router(config-if)#ip address 13.13.13.2 255.255.255.0
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#interface GigabitEthernet0/1
Router(config-if)#ip address 24.24.24.1 255.0.0.0
Router(config-if)#ip address 24.24.24.1 255.255.255.0
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up

router3配置

Router(config)#interface GigabitEthernet0/0
Router(config-if)#ip address 23.23.23.2 255.255.255.0
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#interface GigabitEthernet0/1
Router(config-if)#ip address 24.24.24.2 255.255.255.0
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up

Router(config-if)#exit
Router(config)#exit
Router#vlan database
% Warning: It is recommended to configure VLAN from config mode,
  as VLAN database mode is being deprecated. Please consult user
  documentation for configuring VTP/VLAN in config mode.

Router(vlan)#
%SYS-5-CONFIG_I: Configured from console by console
vlan 10 name VLAN10
VLAN 10 modified:
    Name: VLAN10
Router(vlan)#exit
APPLY completed.
Exiting....
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int vlan 10
Router(config