STM32的串口采用DMA方式发送数据测试

               

STM32的串口采用DMA方式发送数据测试

文博客链接:http://blog.csdn.net/jdh99,作者:jdh,转载请注明.

环境：

主机:WIN7

开发环境:MDK4.23

MCU:STM32F103CBT6

源代码:

配置:

//---------------------串口功能配置---------------------//打开串口对应的外设时钟  RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1 , ENABLE);   //启动DMA时钟RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1, ENABLE);//DMA发送中断设置NVIC_InitStructure.NVIC_IRQChannel = DMA1_Channel4_IRQn;NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 3;NVIC_InitStructure.NVIC_IRQChannelSubPriority = 2;NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;NVIC_Init(&NVIC_InitStructure);//DMA1通道4配置DMA_DeInit(DMA1_Channel4);//外设地址DMA_InitStructure.DMA_PeripheralBaseAddr = (u32)(&USART1->DR);//内存地址DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)Uart_Send_Buffer;//dma传输方向单向DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralDST;//设置DMA在传输时缓冲区的长度DMA_InitStructure.DMA_BufferSize = 100;//设置DMA的外设递增模式，一个外设DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable;//设置DMA的内存递增模式DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable;//外设数据字长DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte;//内存数据字长DMA_InitStructure.DMA_MemoryDataSize = DMA_PeripheralDataSize_Byte;//设置DMA的传输模式DMA_InitStructure.DMA_Mode = DMA_Mode_Normal;//设置DMA的优先级别DMA_InitStructure.DMA_Priority = DMA_Priority_High;//设置DMA的2个memory中的变量互相访问DMA_InitStructure.DMA_M2M = DMA_M2M_Disable;DMA_Init(DMA1_Channel4,&DMA_InitStructure);DMA_ITConfig(DMA1_Channel4,DMA_IT_TC,ENABLE);//使能通道4//DMA_Cmd(DMA1_Channel4, ENABLE);  //初始化参数  //USART_InitStructure.USART_BaudRate = DEFAULT_BAUD;  USART_InitStructure.USART_WordLength = USART_WordLength_8b;  USART_InitStructure.USART_StopBits = USART_StopBits_1;  USART_InitStructure.USART_Parity = USART_Parity_No;  USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;  USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;    USART_InitStructure.USART_BaudRate = DEFAULT_BAUD; //初始化串口 USART_Init(USART1,&USART_InitStructure);  //TXE发送中断,TC传输完成中断,RXNE接收中断,PE奇偶错误中断,可以是多个   USART_ITConfig(USART1,USART_IT_RXNE,ENABLE);  //配置UART1中断  NVIC_PriorityGroupConfig(NVIC_PriorityGroup_3);NVIC_InitStructure.NVIC_IRQChannel = USART1_IRQn;               //通道设置为串口1中断  NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 2;       //中断占先等级0  NVIC_InitStructure.NVIC_IRQChannelSubPriority = 1;              //中断响应优先级0  NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;                 //打开中断  NVIC_Init(&NVIC_InitStructure);                                 //初始化  //采用DMA方式发送USART_DMACmd(USART1,USART_DMAReq_Tx,ENABLE);//启动串口  USART_Cmd(USART1, ENABLE);   //设置IO口时钟      RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_AFIO, ENABLE);    //串口1的管脚初始化    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;                       //管脚9  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_2MHz;                //选择GPIO响应速度  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;                 //复用推挽输出  GPIO_Init(GPIOA, &GPIO_InitStructure);                          //TX初始化  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;                      //管脚10  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_2MHz;                //选择GPIO响应速度  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;           //浮空输入  GPIO_Init(GPIOA, &GPIO_InitStructure);                          //RX初始化                                                      //设置IO口时钟      RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB | RCC_APB2Periph_AFIO, ENABLE);   GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0;                       //管脚9  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_2MHz;                //选择GPIO响应速度  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;                 //复用推挽输出  

中断函数：

//串口1DMA方式发送中断void DMA1_Channel4_IRQHandler(void){ //清除标志位   DMA_ClearFlag(DMA1_FLAG_TC4); //DMA_ClearITPendingBit(DMA1_FLAG_TC4);   //DMA1->IFCR |= DMA1_FLAG_TC4; //关闭DMA DMA_Cmd(DMA1_Channel4,DISABLE);  //DMA1_Channel4->CCR &= ~(1<<0); //允许再次发送 Flag_Uart_Send = 0;}

发送测试：

//串口DMA发送测试Uart_Send_Buffer[0] = 1;Uart_Send_Buffer[1] = 2;Uart_Send_Buffer[2] = 3;Uart_Send_Buffer[3] = 4;Uart_Send_Buffer[4] = 5;i = 1;while (1){ //检查串口是否可以发送 while (Flag_Uart_Send); Flag_Uart_Send = 1; //设置传输数据长度 DMA_SetCurrDataCounter(DMA1_Channel4,i); //打开DMA DMA_Cmd(DMA1_Channel4,ENABLE); i++; if (i > 5) {  i = 1; }}