cisco1

 1

2

3

4

R1路由的配置

Router>

Router>en

Router>enable

Router#conf

Router#configure ter

Router#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#hos

Router(config)#hostname R1

R1(config)#int

R1(config)#interface g0/0

R1(config-if)#ip ad

R1(config-if)#ip address 192.168.1.1 255.255.255.0

R1(config-if)#no sh

R1(config-if)#no shutdown

R1(config-if)#

%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up

R1(config-if)#do ping 192.168.1.110

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 192.168.1.110, timeout is 2 seconds:

.!!!!

Success rate is 80 percent (4/5), round-trip min/avg/max = 0/0/0 ms

 R2路由配置

 

Router>en
Router>enable 
Router#con
Router#conf
Router#configure te
Router#configure terminal 
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#hos
Router(config)#hostname R2
R2(config)#inte
R2(config)#interface s0/0/0
R2(config-if)#ip ad
R2(config-if)#ip address 12.0.0.2 255.255.255.252
R2(config-if)#no sh
R2(config-if)#no shutdown 

%LINK-5-CHANGED: Interface Serial0/0/0, changed state to down
R2(config-if)#inte
R2(config-if)#interf
R2(config-if)#interface g0/0
R2(config-if)#ip ad
R2(config-if)#ip address  172.16.1.1 255.255.255.0
R2(config-if)#no shu
R2(config-if)#no shutdown 

R2(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up

R2(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up

R2(config-if)#
R2(config-if)#do wr
Building configuration...
[OK]
R2(config-if)#
R2(config-if)#ip rou
R2(config-if)#exit
R2(config)#ip ro
R2(config)#ip route 192.168.1.0 255.255.255.0 s0/0/0
%Default route without gateway, if not a point-to-point interface, may impact performance
R2(config)#
R2(config)#do show ip route sta
R2(config)#do show ip route static
S    192.168.1.0/24 is directly connected, Serial0/0/0

R2(config)#

R2 con0 is now available

Press RETURN to get started.

5

去客户端 测试www.test.com

 6

 然后看左下角是不是 successful成功 就行

7

2022-12-1

密码配置

全局模式输入下面

enable password 123

line console 0

password 456

login

line vty 0 4

password 789

login