神码IBGP简单配置

一、拓扑图：

二、地址表

设备	接口	地址	备注
R1	G0/0	192.168.10.2	Loopback1： 10.10.1.1/32
	G0/1	192.168.20.2
SW3-1	E1/0/1	VLAN10:192.168.10.1	Loopback1： 10.10.2.1/32
SW3-2	E1/0/1	VLAN20:192.168.20.1	Loopback1： 10.10.3.1/32

三、任务要求

1.根据拓扑图要求配置设备名称、接口地址、VLAN等。

2.在SW3-1,SW3-2,R1配置IBGP，区域为65001

端口IP配置

R1:

interface GigaEthernet0/0

ip add 192.168.10.2 255.255.255.0

interface GigaEthernet0/1

ip add 192.168.20.2 255.255.255.0

interface loopback 1

ip add 10.10.1.1 255.255.255.255

SW3-1:

vlan 10

interface Vlan10

ip address 192.168.10.1 255.255.255.0

Interface Ethernet1/0/1

Sw acc vlan 10

interface loopback 1

ip add 10.10.2.1 255.255.255.255

SW3-2:

vlan 20

interface Vlan20

ip address 192.168.20.1 255.255.255.0

Interface Ethernet1/0/1

Sw acc vlan 20

interface loopback 1

ip add 10.10.3.1 255.255.255.255

配置OSPF用来通信loopback1

R1：

Router ospf 10

Network 192.168.10.0 0.0.0.255 area 0

Network 192.168.20.0 0.0.0.255 area 0

Network 10.10.1.1 0.0.0.0 area 0

SW3-1：

Router ospf 10

Network 192.168.10.0 255.255.255.0 area 0

Network 10.10.2.1 255.255.255.255 area 0

SW3-2：

Router ospf 10

Network 192.168.20.0255.255.255.0 area 0

Network 10.10.3.1 255.255.255.255 area 0

配置IBGP

R1:

Bgp router-id 1.1.1.1

neighbor 10.10.2.1 remote-as 65001       #指向对方的回环地址加AS区域

neighbor 10.10.2.1 update-source loopback 1        #将本身的回环地址建立邻居

neighbor 10.10.3.1 remote-as 65001

neighbor 10.10.3.1 update-source loopback 1

SW3-1:

Bgp router-id 2.2.2.2

neighbor 10.10.1.1 remote-as 65001

neighbor 10.10.1.1 update-source loopback 1

neighbor 10.10.3.1 remote-as 65001

neighbor 10.10.3.1 update-source loopback 1

SW3-2:

Bgp router-id 3.3.3.3

neighbor 10.10.1.1 remote-as 65001

neighbor 10.10.1.1 update-source loopback 1

neighbor 10.10.2.1 remote-as 65001

neighbor 10.10.2.1 update-source loopback 1