DS4800 用串口登陆0.1改成85状态

 DS4800 用串口登陆0.1改成85状态
1、首先按ctrl+break提示如下

space> within 5 seconds
Baud rate set to 9600

Press within 5 seconds: <ESC> for SHELL, <BREAK> for baud rate ***** Cancelled

Press within 5 seconds: <ESC> for SHELL, <BREAK> for baud rate

2、按esc进入如下界面，输入密码：infiniti

Current date: 11/19/10  time: 22:54:22

Enter password to access shell: 
Password incorrect

Enter password to access shell: 
Engenio RAID Controller
Copyright Engenio Information Technologies, Inc., 2004-2006
Copyright Wind River Systems, Inc., 1998-2002
VxWorks: VxWorks5.5.1   Kernel: WIND version 2.6
Mode
Press within 5 seconds: <ESC> for SHELL, <BREAK> for baud rate
Set baud rate: press <space> within 5 seconds l: 6091    Firmware version: 06.14.28.00

 

->
Baud rate set to 9600
 
->
3、输入M字符，如下所示：
-> M
value = 0 = 0x0
->

NOTICE: The BOOT OPERATIONS MENU has been invoked too late for
proper operation of some activities, including Isolation Diagnostics.
You may wish to restart this controller again and press Control-B
IMMEDIATELY after seeing the start-up indicator ("-=<###>=-").

 

                           BOOT OPERATIONS MENU

 1) Perform Isolation Diagnostics    10) Serial Interface Mode Menu
 2) Download Permanent File          11) Display Hardware Configuration
 3) Reserved                         12) Change Hardware Configuration Menu
 4) Dump NVSRAM Group                13) Development Options Menu
 5) Patch NVSRAM Group               14) Display Memory Error Log
 6) Set Real Time Clock              15) Manufacturing Setup Menu
 7) Display Board Configuration       R) Restart Controller
 8) Special Services Menu             Q) Quit Menu
 9) Display Exception Message

    Enter Selection: 12

                      CHANGE HARDWARE CONFIGURATION MENU

    -------SOFTWARE SWITCH OPTION--------  --CURRENT--  --DEFAULT--
 1) Switch #1 (PCI Device Config Disable)      Default      Off
 2) Switch #2 (Manufacturing Diagnostics)      Default      Off
 3) Switch #3 (Invoke Boot Menu)               Default      Off
 4) Switch #4 (Continuous Diagnostics)         Default      Off

    ----------SOFTWARE OPTION------------  --CURRENT--
 5) Option #1 (Extensive Diagnostics)          Off   
 6) Option #2 (Diagnostics Disable)            Off   
 7) Option #3 (Autoload Disable)               On    
 8) Option #4 (Network Enable)                 On      (NVSRAM Enabled)

    ------------VALUE OPTION-------------  --CURRENT--  --DEFAULT--
 9) Host SCSI Id                               0x04         0x04
10) Reserved                                   0x00         0x00
11) Buffer Memory Size (MB)                    0x00         0x00
12) Board Id                                   0x28         0x28
13) Reserved                                   0x00         0x00

 R) Reset all options
 C) Cancel all changes and quit
 H) Help
 Q) Quit Menu
4、输入R，重置所有选项！
5、等待1分钟后，启动完成。正常，LED灯显示85
    Enter Selection: R

                      CHANGE HARDWARE CONFIGURATION MENU

    -------SOFTWARE SWITCH OPTION--------  --CURRENT--  --DEFAULT--
 1) Switch #1 (PCI Device Config Disable)      Default      Off
 2) Switch #2 (Manufacturing Diagnostics)      Default      Off
 3) Switch #3 (Invoke Boot Menu)               Default      Off
 4) Switch #4 (Continuous Diagnostics)         Default      Off

    ----------SOFTWARE OPTION------------  --CURRENT--
 5) Option #1 (Extensive Diagnostics)          Off   
 6) Option #2 (Diagnostics Disable)            Off   
 7) Option #3 (Autoload Disable)               Off   
 8) Option #4 (Network Enable)                 Off     (NVSRAM Enabled)

    ------------VALUE OPTION-------------  --CURRENT--  --DEFAULT--
 9) Host SCSI Id                               0x04         0x04
10) Reserved                                   0x00         0x00
11) Buffer Memory Size (MB)                    0x00         0x00
12) Board Id                                   0x28         0x28
13) Reserved                                   0x00         0x00

 R) Reset all options
 C) Cancel all changes and quit
 H) Help
 Q) Quit Menu

    Enter Selection: q齊c
                         }蚤俏B?cN^j尬

Current date: 11/19/10  time: 22:55:41

Send <BREAK> for shell access or baud rate change
11/19/10-22:55:44 (GMT) (tRAID): NOTE:  rpaBattMgr instantiation starting.
11/19/10-22:55:44 (GMT) (tRAID): NOTE:  rpaBattery Init starting.
11/19/10-22:55:44 (GMT) (tRAID): NOTE:  rpaBattMgr instantiation complete.

Network Ready
11/19/10-22:55:45 (GMT) (tRAID): NOTE:  lockMgr Role is Master
11/19/10-22:55:45 (GMT) (tRAID): NOTE:  Failing The Alternate Controller
11/19/10-22:55:45 (GMT) (tRAID): NOTE:  holding alt ctl in reset
11/19/10-22:55:47 (GMT) (tRAID): NOTE:  hddWwnSearch: unable to find0000000000000000
11/19/10-22:55:47 (GMT) (tRAID): NOTE:  Change WWN baseName from 000400a0-b83254bc to 000400a0-b8325348 because: OnlyCtl
11/19/10-22:55:47 (GMT) (tRAID): NOTE:  hddWwnSearch: unable to find0000000000000000
11/19/10-22:55:47 (GMT) (tRAID): NOTE:  WWN baseName 000400a0-b8325348 (valid==>NewBaseNoChk)
11/19/10-22:55:49 (GMT) (hddCyclic): NOTE:  hddChanReport ==> -0 -1 -2 +3 =4 =5 =6 =7
11/19/10-22:55:51 (GMT) (IOSched): NOTE:  Extended Link Down  ==> Chan 0
11/19/10-22:55:51 (GMT) (IOSched): NOTE:  Extended Link Down  ==> Chan 1
11/19/10-22:55:51 (GMT) (tRAID): NOTE:  HDD waiting for channel 0 to stabilize
11/19/10-22:55:51 (GMT) (tRAID): NOTE:  HDD waiting for channel 1 to stabilize
11/19/10-22:55:51 (GMT) (hddCyclic): NOTE:  hddChanReport ==> =0 =1 +2  3 =4 =5 =6 =7
11/19/10-22:55:52 (GMT) (tRAID): NOTE:  HDD waiting for channel 0 to stabilize
11/19/10-22:55:52 (GMT) (tRAID): NOTE:  HDD waiting for channel 1 to stabilize
11/19/10-22:55:53 (GMT) (tRAID): NOTE:  HDD waiting for channel 0 to stabilize
11/19/10-22:55:53 (GMT) (tRAID): NOTE:  HDD waiting for channel 1 to stabilize
11/19/10-22:55:54 (GMT) (tRAID): NOTE:  HDD waiting for channel 0 to stabilize
11/19/10-22:55:54 (GMT) (tRAID): NOTE:  HDD waiting for channel 1 to stabilize
11/19/10-22:55:55 (GMT) (tRAID): NOTE:  HDD waiting for channel 0 to stabilize
11/19/10-22:55:55 (GMT) (tRAID): NOTE:  HDD waiting for channel 1 to stabilize
11/19/10-22:55:56 (GMT) (tRAID): NOTE:  HDD waiting for channel 0 to stabilize
11/19/10-22:55:56 (GMT) (tRAID): NOTE:  HDD waiting for channel 1 to stabilize
11/19/10-22:55:57 (GMT) (tRAID): NOTE:  HDD waiting for channel 0 to stabilize
11/19/10-22:55:57 (GMT) (tRAID): NOTE:  HDD waiting for channel 1 to stabilize
11/19/10-22:55:58 (GMT) (tRAID): NOTE:  HDD waiting for channel 0 to stabilize
11/19/10-22:55:58 (GMT) (tRAID): NOTE:  HDD waiting for channel 1 to stabilize
11/19/10-22:55:59 (GMT) (tRAID): NOTE:  HDD waiting for channel 0 to stabilize
11/19/10-22:55:59 (GMT) (tRAID): NOTE:  HDD waiting for channel