14Gbps850nm SFP+ Transceiver,100m Reach storage module

SOSP-8596-01

1. Applications

Ø  Tri-Rate 14.025 Gb/s Fibre Channel

Ø  Other optical links

 

2.Features

Ø  Up to 14.025 Gb/s bi-directional data links

Ø  Hot-pluggable SFP+ footprint

Ø  Built-in digital diagnosticfunctions

Ø  Built-in CDR with shut offcontrol

Ø  850nm Oxide VCSEL lasertransmitter

Ø  Duplex LC connector

Ø  RoHS compliant and Lead Free

Ø  35m on 50/125um MMF

Ø  100m on high-bandwidth 50/125um(OM3)

Ø  Metal enclosure, for lower EMI

Ø  Single 3.3V power supply

Ø  Operating temperature range:0°C to 70°C

3. Description

Sinovo’s 16G SW SFP+ transceivers are designed for use in Fibre Channel links up to14.025

Gb/s data rateover multimode fiber.   They are compliantwith FC-PI-5 Rev. 6.00a, SFF-8472 Rev 11.0c and SFF-8081h, andcompatible with SFF-8432b and applicable portions of SFF-8431 Rev. 4.1d.The opticaltransceiver is compliant per the RoHS.

4.standard

Ø  Electrical interface compliant toSFF-8431

Ø  Compliant with SFF-8472 Rev 10.2

Ø  Compliant with IEEE 802.3ae10GBASE-LR and 10GBASE-LW

Ø  RoHS Compliant

5.Performance Specifications

5.1.Absolute Maximum Ratings

These values represent the damage threshold of the module. Stress inexcess of any of the individual Absolute Maximum Ratings can cause immediatecatastrophic damage to the module even if all other parameters are withinRecommended Operating Conditions.

Table.1 Absolute maximumratings

Parameter	Symbol	Min	Max	Unit
Maximum Supply Voltage	Vcc	-0.5	4.0	V
Storage Temperature	Ts	0	70	°C
RX Input Average Power	Pmax		0	dBm
Relative Humidity	RH	5	85	%

 

5.2.Recommended Operating Conditions

Table.2 RecommendedOperating Conditions

Parameter	Symbol	Min	Typical	Max	Unit
Operating Case Temperature	Standard Tc	0	25	70	°C
Power Supply Voltage	Vcc	3.15	3.3	3.46	V
Power Supply Current	Icc			290	mA
Power Dissipation	PD	90		800	mW
Data Rate	DR		14.025		Gbps
Transmission Distance	TD		100		m

 

5.3. Transmitter Specification

Table.3 TransmitterSpecification (Optical)

Parameter	Symbol	Min.	Typ.	Max.	Unit	Note
Average Output Power	Po	-7.8			dBm
Disable Power	Poff			-40	dBm
Extinction Ratio	ER	3.5			dB
Output Centre Wavelength	λc	840		860	nm
Spectral Width (RMS) @ 14.025Gb/s	Δλ			0.59	nm
Optical Modulation Amplitude @ 14.025 Gb/s	OMA	-4.8			dBm
Optical Return Loss	ORL			-12	dB
Transmitter Waveform and Dispersion Penalty	DP			4.3	dB
Optical Rise/Fall Time (20%~80%)@	tr/tf			0.09	ns
Optical Eye Mask	MM	Compliant to IEEE802.3ae				1
Relative Intensity Noise	Rin			-128(12dB reflection)	dB/Hz

Note: 1. Measured at 14.025Gbps, PRBS2^31-1, NRZ

Table.4 TransmitterSpecification (Electrical)

Parameter		Symbol	Min	Typical	Max	Unit
Data Input Swing Differential		VIN	90		800	mV
Input Differential Impedance		ZIN	90	100	110	Ω
Transmit Disable Input	High	VIH	2.0		Vcc+0.3	V
	Low	VIL	0		0.8	V
Transmit Enable Output	High	VOH	Vee		Vee+0.8	V
	Low	VOL	0		0.4	V

 

 

 

5.4. Receiver Specification

Table.5 ReceiverSpecification (Optical)

Parameter	Symbol	Min	Typical	Max	Unit	note
Centre Wavelength	λc	840	850	860	nm
Receiver Sensitivity	Sen			-10.5	dBm	2
Receiver Overload	Psat	0			dBm	2
LOS De-Assert	LOSD			-13	dBm
LOS Assert	LOSA	-30			dBm
LOS Hysteresis		0.5			dB
Receiver Reflectance	Rrx			-12	dB

Note :2. Measured at BER10-12, 14.025Gbps, PRBS2^31-1, NRZ

Table.6 ReceiverSpecification (Electrical)

Parameter		Symbol	Min	Typical	Max	Unit	note
Data Output Swing Differential		Vout	185		425	mV
Deterministic Jitter @ 14.025 Gb/s		RX DJ			0.22	UI
LOS Output	High	VOH	2		Vcc+0.3	V
	Low	VOL	Vee		Vee+0.8	V

 

 

5.5. Diagnostics Specification

 

Table.7Diagnostics Specification

Parameter	Range	Unit	Accuracy	Calibration
Temperature	0 to 70	℃	±3℃	Internal / External
Voltage	3.0 to 3.6	V	±3%	Internal / External
Bias Current	0 to 100	mA	±10%	Internal / External
TX Power	-7.8 to 0	dBm	±3dB	Internal / External
RX Power	-30 to 0	dBm	±3dB	Internal / External

 

 

 

5.6. Pin Definitions

Table.8Pin Definitions

PIN	Symbol	Description	Remarks
1	VEET	Transmitter ground (common with receiver ground)	Circuit ground is isolated from chassis ground
2	Tx_Fault	Transmitter Fault. Not supported
3	Tx_Disable	Transmitter Disable. Laser output disable on high or open	Disabled: TDIS>2V or open Enabled: TDIS<0.8V
4	SDA	2-wire Serial Interface Data Line	Should Be pulled up with 4.7k – 10k ohm on host board to a voltage between 2V and 3.6V
5	SCL	2-wire Serial Interface Clock Line
6	MOD_ABS	Module Absent. Grounded within the module.
7	RS0	No connection required
8	RX_LOS	Loss of Signal indication. Logic 0 indicates normal operation	LOS is open collector output
9	RS1	No connection required
10	VEER	Receiver ground (common with transmitter ground)	Circuit ground is isolated from chassis ground
11	VEER	Receiver ground (common with transmitter ground)
12	RD–	Receiver Inverted DATA out. AC coupled
13	RD+	Receiver Non-inverted DATA out. AC coupled
14	VEER	Receiver ground (common with transmitter ground)	Circuit ground is isolated from chassis ground
15	VCCR	Receiver power supply
16	VCCT	Transmitter power supply
17	VEET	Transmitter ground (common with receiver ground)	Circuit ground is isolated from chassis ground
18	TD+	Transmitter Non-Inverted DATA in. AC coupled
19	TD–	Transmitter Inverted DATA in. AC coupled
20	VEET	Transmitter ground (common with receiver ground)	Circuit ground is isolated from chassis ground

 

5.7. Timing Electrical Interface

 

Table.9 Timing ElectricalInterface

Parameter	Symbol	Min	Max	Units	Conditions
Tx_Disable Assert Time	t_off		100	us	Rising edge of Tx_Disable to fall of output signal below 10% of nominal
Tx_Disable Negate Time	t_on		2	ms	Tx_Disable negate time. Falling edge of Tx_Disable to rise of output signal above 90% of nominal. This only applies in normal operation, not during start up or fault recovery.
Time to initialize	t_start_up		300	ms	From power supplies or hot plug or Tx disable negated during power up, or Tx_Fault recovery, until non-cooled power level I is fully operational.
Tx_Fault Assert Time	Tx_Fault		1	ms	From occurrence of fault to assertion of Tx_Fault
Tx_Fault to Reset	t_reset	10		us	Time Tx_Disable must be held high to reset Tx_Fault
Rx_LOS Assert Time	t_los_on		100	us	From occurrence of loss of signal to assertion of Rx_LOS
Rx_LOS De-Assert Time	t_los_off		100	us	From occurrence of presence of signal to negation of Rx_LOS

 

 

 

 

 

 

 

 

 

 

5.8. Mechanical Dimensions

 

Diagram of Mechanical Dimensions

6.Aplication Cautions

6.1.ESD

Thistransceiver is specified as ESD threshold 1kV for high speed pins and 2kV forall other electrical input pins, tested per MIL-STD-883, Method 3015.4/JESD22-A114-A (HBM).  However, normalESD precautions are still required during the handling of this module. Thistransceiver is shipped in ESD protective packaging. It should be removed fromthe packaging and handled only in an ESD protected environment.

6.2. LASER SAFTY

This is aClass 1 Laser Product according to IEC 60825-1:1993:+A1:1997+A2:2001.  This product complies with 21 CFR 1040.10 and1040.11 except for deviations pursuant to Laser Notice No. 50, dated (July 26,2001)

 

 Contact :

Address	11/F,Taibang Technology Building,Gaoxin South 4th,Science and Technology Park South,Nanshan,Shenzhen,China
Zip	518040
Tel	+86(0)0755-3295 9919
Fax	+86(0)755 3295 9918
Website	www.sinovocorp.com